Advertisement
.............
AX-3000
Users Manual
.............
!
THE SOCKET-OUTLET SHALL BE INSTALLED NEAR THE EQUIPMENT AND
SHALL BE EASILY ACCESSIBLE.
LA PRISE DOIT ETRE PRES DE L'APPAREIL ET FACILE D'ACCES.
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
[AX3000] USR-005
series
2012-09-28
Advertisement
Table of Contents
Related Manuals for Uniwell AX-3000 series
Summary of Contents for Uniwell AX-3000 series
- Page 1 [AX3000] USR-005 2012-09-28 ……..….. AX-3000 series Users Manual ……..….. THE SOCKET-OUTLET SHALL BE INSTALLED NEAR THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE. LA PRISE DOIT ETRE PRES DE L'APPAREIL ET FACILE D'ACCES. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
-
Page 2: Table Of Contents
In case if POS is locked down..................9 Notes: 1. The contents of this manual are subject to change without notice. 2. Uniwell cannot be held responsible, if other products which are not approved by Uniwell, are used for options or expendable supplies. -
Page 3: Attention
SERIAL No: (Please see the label on the machine.) DATE OF PURCHASE: YOUR DEALER: (where purchased) Manufacturer Uniwell Corporation 4-32, 1-chome, Doshin, Kita-ku, Osaka, 530-0035, JAPAN http://www.uniwell.com/ Contact within DDS – Daon Data Systems GmbH EU community 1-K, 63110 Rodgau, Germany... -
Page 4: Introduction
I. Introduction This model is New generation of Touch Screen POS terminals for Restaurants, Bars / Pubs and Fast-food stores having a lot of functions. Main Features New Generation of POS terminal with high-speed CPU and Real Time OS Solid-state technology (No moving parts, No Hard Disk, No fan) offers reliability and stability of Embedded system. -
Page 5: Parts Names
Parts Names Touch Screen (angle adjustable from 0 to 70 degree) Interface (side) Card Reader (option) The swiping direction of card reader is up to down. Power ON Switch Clerk iButton (option) Interface (bottom) and Main Power Switch for Emergency COM 2 COM 1 DC12V... -
Page 6: Hardware Specifications
Hardware Specifications Processor (CPU) 32 bit ARM9 RISC Processor, 177 MHz SDRAM 64 M Byte Memory Flash Memory 8 M Byte SRAM 8 M Byte 15 inch 4 wire resistive type Touch Panel Light load type, antifouling film 15 inch TFT XGA color 1024 (H) x RGB x 768 (V) Operator Display Adjustable angle: 0 ~ 70°... -
Page 7: Installation And Remarks
II. Installation and Remarks Precautions to use this POS safely Should not be installed in extremely hot or cold environments, places exposed to direct sunlight, or excessive dust or liquid. --- It will cause overheating, malfunction or fire. Use the specified power supply according to POS models. --- It will cause overheating or fire. -
Page 8: Remarks
Remarks Check the following before using POS 1) The required peripheral(s) has (have) been connected to the correct interface connector(s); 2) The power plug is connected to AC outlet. Attention for the handling of Touch Panel The surface of touch panel is made from PET sheet with hard coat treatment. In order not to damage the touch panel, please kindly note the following points: 1) Always press touch panel by a finger. - Page 9 Interface Cover Before you connect / disconnect the cable to the peripheral(s), make sure that the power is "OFF". 1) Pull the cover by pushing two hooks to remove the interface cover. 2) Insert 3 projections into the opening of the cabinet and two hooks likewise. Close the cover by pushing the positions (not hooks) on the cover indicated by triangles in the image below.
- Page 10 Cable Management (how to clamp the cables) 1) The clamper for cables is placed in the base. Pull up the LCD case by both hands to see the clamper in the base. Clamper Close Clamper Open 2) In order to open the clamper, slide the clamper downward. 3) Run the cables through the clamper and close the clamper by pushing.
-
Page 11: How To Clean The Cabinet And Touch Screen
How to Clean the Cabinet and Touch Screen When the cabinet and touch screen become dirty, please wipe them with a soft piece of cloth. As for the touch screen, do not wipe it hard with a soft piece of cloth even if the protect sheet is attached on it. - Page 12 The crossed-out wheeled bin symbol is used to show that this product must not be treated as general household waste. Please contact the supplier of this product to ensure that it is disposed of correctly. You will be helping to prevent potentially negative consequences for the environment and human health, which could otherwise be caused by incorrect waste handling of the...