Advertisement

INSTRUCTION MANUAL
.
.
.
MODEL NUMBER: HE161192
VERSION 1
ISSUED 23/11/17

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the HE161192 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Cocoon HE161192

  • Page 1 INSTRUCTION MANUAL MODEL NUMBER: HE161192 VERSION 1 ISSUED 23/11/17...
  • Page 3 IMPORTANT Getting the most out of your 3D Printer Touch: Read the manual carefully It will help you set up with ease Visit www.cocoonproducts.com.au We have additional support videos and guides Call After Sales Support - 1300 663 907 Available Monday - Friday, 8:30am - 6:00pm AEST Email customercare@winplus.com.au We’re always happy to help WARRANTY NOTE...
  • Page 4: Warranty Details

    You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. AFTER SALES SUPPORT 1300 663 907 customercare@winplus.com.au YEAR WARRANTY MODEL: HE161192 PRODUCT CODE: 56826 01/2018...
  • Page 5: Safety Instructions

    CAUTION: The Cocoon Create 3D Printer Touch generates high temperatures and includes moving parts that can cause injury. Never reach inside of the Cocoon Create 3D Printer Touch while it is in operation, and allow time for the printer to cool down after operation.
  • Page 6: Table Of Contents

    CONTENTS Warranty Details Safety Instructions Parts List Technical Specifications Introduction 1.1 What is 3D Printing? 1.2 From 3D Design to Printed 3D Object 1.3 Good 3D Printing Practices Product Overview 2.1 Printer Front View 2.2 Printer Rear View 2.3 Print Bed 2.4 Control Panel 2.5 Touch Screen Control Panel Setup...
  • Page 7 Maintenance Disposal of Packaging Disposal of Product Troubleshooting 10.1 Troubleshooting 10.1.1 Printing Problems 10.1.2 Connectivity Problems 10.1.3 Other Problems 10.2 Useful Terms Appendix References Repair and Refurbished Goods or Parts Notice AFTER SALES SUPPORT 1300 663 907 CUSTOMERCARE@WINPLUS.COM.AU MODEL: HE161192...
  • Page 8: Parts List

    PARTS LIST 1 x Cocoon Create 3D Printer 1 x Scraper 1 x 0.4mm Drill Bit Touch (Extruder Tower, 1 x Replacement PTFE Tube 1 x Extruder Cleaner Heated Print Bed) 1 x Hex Key Set 6 x Rubber Feet...
  • Page 9: Technical Specifications

    Extruder Diameter: 0.4mm Print Speed: 10mm/s - 70mm/s Travel Speed: 10mm/s - 70mm/s Supported Print Materials: Cocoon Create Branded PLA, ABS, PVA, HIPS, PLA Wood, PLA Flex, Conductive Temperature Ambient Operating Temperature: 15°C – 30°C Operational Extruder Temperature: 170ºC – 255ºC Operational Print Bed Temperature: 15ºC –...
  • Page 10: Introduction

    INTRODUCTION 1.1 What is 3D Printing? 3D Printing is a process whereby a real object is created from a 3D Design. Fused Filament Fabrication (FFF) is one of the most common technologies used by 3D Printers to achieve this. FFF works on an ‘additive’...
  • Page 11 Once the printer has completed all the layers, you will have a 3D Printed Model. The Cocoon Create 3D Printer Touch is compatible with a broad range of filament types and is capable of printing 3D models ranging from small and simple to complex objects with moving parts.
  • Page 12: Good 3D Printing Practices

    INTRODUCTION 1.3 Good 3D Printing Practices Please refer to these steps during every print to ensure the best quality. Before Printing Ensure your GCODE file is correctly setup, filament diameter is set to 1.75mm and correct temperature settings for the material you are using (refer to table 3.3.1, page 24) Check all cables and connectors are connected Check that Heated Print Bed is level and approximately 0.1mm from the nozzle Check that Heated Print Bed is clean and dust free and nozzle does not have excess material...
  • Page 13: Product Overview

    8. Filament Spool Holder 2. X Belt Drive 6. Filament Cooling Fan Assembly 3. Extruder Spring Lever 7. Extruder Driving Motor 9. Tower Frame 4. Extruder Cooling Fan 10. Touch Screen AFTER SALES SUPPORT 1300 663 907 CUSTOMERCARE@WINPLUS.COM.AU MODEL: HE161192...
  • Page 14: Printer Rear View

    PRODUCT OVERVIEW 2.2 Printer Rear View 1. X Cable Track 4. Extruder 7. Z Stop (Micro Switch) 2. X Axis Stepper Motor 5. Z Drive Screw 8. Z Axis Stepper Motor 3. Z Cable Track 6. Z Rod...
  • Page 15: Print Bed

    1. Y Stop (Micro Switch) 4. Levelling Thumb Screw 7. Y Belt Drive 2. Heated Print Bed 5. Print Bed Frame 8. Y Rail 3. Printing Mat 6. Y Axis Stepper Motor AFTER SALES SUPPORT 1300 663 907 CUSTOMERCARE@WINPLUS.COM.AU MODEL: HE161192...
  • Page 16: Control Panel

    PRODUCT OVERVIEW 2.4 Control Panel 1. Touch Screen 3. Mini USB Port 5. Power Switch 2. SD Port 4. Power Socket...
  • Page 17: Touch Screen Control Panel

    NOTE: If you are making changes in ‘Settings’ , ensure you select ‘Confirm’ to proceed to update the changes made for your current print file • Stop: Stops the current print job completely • Back: Return to Main Menu AFTER SALES SUPPORT 1300 663 907 CUSTOMERCARE@WINPLUS.COM.AU MODEL: HE161192...
  • Page 18 PRODUCT OVERVIEW Quick Menu • Preheat: Preheat Extruder and Heat Bed Temperature for PLA or ABS filament • Home XZY: Automatically resets Extruder location to Home position • Move: • -X Axis+: Move the Extruder along the X-Axis manually • -Z Axis+: Move the Extruder along the Z-Axis manually •...
  • Page 19 • • E-Axis: • Confirm: Select to update print settings • Back: Return to Advance Settings • Factory Reset: Resets 3D Printer to default Settings • Back: Return to Main Menu AFTER SALES SUPPORT 1300 663 907 CUSTOMERCARE@WINPLUS.COM.AU MODEL: HE161192...
  • Page 20: Setup

    SETUP 3.1 Unboxing and Assembly Your Cocoon Create 3D Printer Touch is packed tightly and carefully - take your time unpacking it. To view a step by step video of the Unboxing and Assembly, visit cocoonproducts.com.au Carefully remove the Extruder Tower and Heated Print Bed from the box and place them on a clean, level work space.
  • Page 21 3D Printer Base Wait for the printer to initialise, with the home screen shown on the Touch Screen. You have successfully setup your Cocoon 3D Printer Touch AFTER SALES SUPPORT 1300 663 907 CUSTOMERCARE@WINPLUS.COM.AU...
  • Page 22: Levelling The Bed

    SETUP 3.2 Levelling the Bed IMPORTANT NOTE: Levelling the bed is an extremely important step and if it is not done correctly every time, your prints will fail or be of poor quality Before you begin to level the Heated Print Bed: •...
  • Page 23 Move the Extruder to the centre of the Heated Print Bed and test the gap with the levelling card or a sheet of paper. Keep adjusting and testing until the gap is uniform on all points of the bed AFTER SALES SUPPORT 1300 663 907 CUSTOMERCARE@WINPLUS.COM.AU MODEL: HE161192...
  • Page 24: Filament

    SETUP 3.3 Filament The Cocoon Create 3D Printer Touch uses high quality PLA and ABS filaments. Only use quality Cocoon Create filaments as using generic filaments may damage your 3D Printer Touch, affect the print quality and may void your warranty. Extra filament including multiple colours and types are available from the online store at cocoonproducts.com.au.
  • Page 25: Inserting Filament

    PLA or ABS for an extended period of time, follow these tips. • Store in a sealed, air tight bag/container. We recommend a vacuum seal bag • Store with a silica gel (moisture absorber) pack. One is included with each filament spool AFTER SALES SUPPORT 1300 663 907 CUSTOMERCARE@WINPLUS.COM.AU MODEL: HE161192...
  • Page 26: Using The Sd Card

    SETUP 3.4 Using the SD Card 3.4.1 Loading files from your Computer Insert your SD Card into a card reader or memory card slot and connect to your computer (refer to your computer manual for further instructions if required) The SD Card will appear as a folder (refer to your computer manual for further instructions if required) Copy your converted GCODE files to the SD card, then safely remove 3.4.2 Printing from the SD Card...
  • Page 27: Removing 3D Objects From The Bed

    SETUP 3.5. Removing 3D Objects from the Bed When the Cocoon Create 3D Printer Touch has completed printing your 3D printed object, it’s time to remove the object from the bed. Once the print is completed, the nozzle and Heated Print Bed will automatically commence cooling down.
  • Page 28: Preparing To Print A File

    PREPARING TO PRINT A FILE 4.1 Creating a GCODE File The Cocoon Create 3D Printer Touch prints 3D files in GCODE format. GCODE files provide essential movement and printer settings required to print your object. To prepare and convert your 3D file to GCODE format, you must use a ‘Slicer’...
  • Page 29: Servicing

    SERVICING 5.1 Servicing your 3D Printer Touch 5.1.1 Replacing the Print Mat The Cocoon Create 3D Printer Touch includes 2 Extra Print Mats. Additional Print Mats are available for purchase from cocoonproducts.com.au Remove the current Print Mat by slowly peeling from one corner...
  • Page 30: Extruder Cleaning

    SERVICING 5.1.3 Extruder Cleaning If your Extruder becomes blocked, follow these steps to unclog the Extruder. Remove the existing filament using steps from section 3.3.3 ‘Removing Filament’ Gently press down on the Extruder lever, and carefully insert the Extruder Cleaner into the filament hole.
  • Page 31: Finishing

    Using the long-nose pliers, carefully grasp some of the remaining material, then twist to remove. Repeat until no more material can be removed. Using the wire cutters, cut away any excess filament. AFTER SALES SUPPORT 1300 663 907 CUSTOMERCARE@WINPLUS.COM.AU MODEL: HE161192...
  • Page 32: Sanding

    FINISHING 6.1.3 Sanding Though Fused Filament Fabrication (FFF) is capable of producing high quality objects straight out of the machine, the layer lines will be visible. Sanding will reduce these ‘step’ marks in the model. Ensure that safety goggles and a mask are worn for protection Starting with 100 grit sandpaper, carefully sand your 3D object using small, circular motions NOTE: PLA is less resistant to high temperatures caused by sanding.
  • Page 33: Maintenance

    Observe any local regulations regarding the disposal of electrical consumer goods and dispose of it appropriately for recycling. Contact your local authorities for advice on recycling facilities in your area. AFTER SALES SUPPORT 1300 663 907 CUSTOMERCARE@WINPLUS.COM.AU MODEL: HE161192...
  • Page 34: Troubleshooting

    TROUBLESHOOTING 10.1 Troubleshooting If having any troubles when using the 3D Printer Touch, please refer to the troubleshooting guide below, or call customer support on 1300 663 907. You can also visit cocoonproducts.com.au for support videos and advanced tutorials. 10.1.1 Printing Problems Clicking sound from one of the stepper motors One of your stepper motors may not be connected properly.
  • Page 35: Connectivity Problems

    Check that you have correctly inserted the power cable into the rear of the Control Box, the power cord is plugged into the mains outlet and that the Control Box power switch is on. AFTER SALES SUPPORT 1300 663 907 CUSTOMERCARE@WINPLUS.COM.AU MODEL: HE161192...
  • Page 36: Other Problems

    What types of filament can my 3D Printer Touch Print? The Cocoon Create 3D Printer Touch accepts various types of filaments including PLA, ABS, PVA, HIPS and specialty filaments such as wood, flexible, luminous and conductive. For our full range of filaments visit cocoonproducts.com.au...
  • Page 37 DC motors that move in discrete steps. This allows for precise positioning and/or speed control .stl A common file format for 3D Designs/Models USB Cable This cable allows communication between the Cocoon Create 3D Printer Touch and a computer, using the USB port of the computer AFTER SALES SUPPORT 1300 663 907 CUSTOMERCARE@WINPLUS.COM.AU...
  • Page 38: Appendix

    APPENDIX References Some of the 3D Models used in this manual and other included materials were sourced from the below:...
  • Page 39: Repair And Refurbished Goods Or Parts Notice

    Please telephone us on 1300 663 907 or write to us at: Winplus Australasia PO Box 537 Bayswater Business Centre, Victoria, Australia 1300 663 907 - Hours: Mon-Fri 8:30am - 6:00pm AEST customercare@winplus.com.au AFTER SALES SUPPORT 1300 663 907 customercare@winplus.com.au YEAR WARRANTY MODEL: HE161192 PRODUCT CODE: 56826 01/2018...

Table of Contents

Save PDF