Subscribe to Our Youtube Channel
Related Manuals for Bivocom TW810-B5
Summary of Contents for Bivocom TW810-B5
- Page 1 Industrial NB-IoT Cellular Modem TW810 Series User Guide Addr.: Unit 704, No. A3 Building, Tel: +86-592-6211770 Software Park, Xiamen, China 361000 Fax: +86-592-6211727 www.bivocom.com sales@bivocom.com...
-
Page 2: Copyright
Product specifications and information in this document are subject to change without any notice, and BIVOCOM reserves the right to improve and change this user guide at any time. Users should take full responsibility for their application of products, and Xiamen Bivocom Technologies Co., Ltd. -
Page 3: About This Guide
About This Guide Thank you for choosing BIVOCOM Industrial Cellular NB-IoT Modem TW810 Series. Please thoroughly read this user guide before you configure and install the device. This manual is compatible with below models Model Description TW810-B5 Industrial NB-IoT Modem(850MHz) -
Page 4: Table Of Contents
4.2.5 Communication Baud Rate............15 4.2.6 Databit, Parity and Stopbit ............15 4.2.7 Frame Interval (Unit: Millisecond) ..........15 4.2.8 Trigger Settings ................16 Addr.: Unit 704, No. A3 Building, Tel: +86-592-6211770 Software Park, Xiamen, China 361000 Fax: +86-592-6211727 www.bivocom.com sales@bivocom.com... - Page 5 4.3.13 TTL Heartbeat ................21 4.5 MODBUS Setting ................. 21 Firmware Upgrade ..................21 Appendix 1: AT Command ................24 Appendix 2: FAQ ....................26 Addr.: Unit 704, No. A3 Building, Tel: +86-592-6211770 Software Park, Xiamen, China 361000 Fax: +86-592-6211727 www.bivocom.com sales@bivocom.com...
-
Page 6: Definitions
A computer for receiving data sent from NB-IoT Modem through NB-IoT network, and sending data to NB-IoT Modem through NB-IoT network. 1.3 TW810 An industrial NB-IoT Modem series manufactured by Bivocom. 2. Introduction 2.1 Overview TW810 Series NB-IoT Modem is a type of industrial wireless NB-IoT Modem (Also called DTU, Data Transfer Unit, or IP modem), designed to fully meet the needs of industrial standards and industrial users. -
Page 7: Getting Started
Check the package before you configure and install the device. TW810 NB-IoT Modem Host Cellular antenna(SMA Male) Power Adapter(12VDC/0.5A) 3- Pin RS232 cable 12-Pin Terminal Block Addr.: Unit 704, No. A3 Building, Tel: +86-592-6211770 Software Park, Xiamen, China 361000 Fax: +86-592-6211727 www.bivocom.com sales@bivocom.com... -
Page 8: Dimensions
3.2 Dimensions There are 3 holes for installation at each side of TW810 (Unit: mm) 3.3 Installation Addr.: Unit 704, No. A3 Building, Tel: +86-592-6211770 Software Park, Xiamen, China 361000 Fax: +86-592-6211727 www.bivocom.com sales@bivocom.com... -
Page 9: Sim/Uim Card
3.3V switch signal TTL TX GPIO, able to check dry contact Reserved RS232 DCD signal and 3.3 V switch signal, output 3.3V switch signal Addr.: Unit 704, No. A3 Building, Tel: +86-592-6211770 Software Park, Xiamen, China 361000 Fax: +86-592-6211727 www.bivocom.com sales@bivocom.com... -
Page 10: Power Supply
TW810 adopts advanced power technology to improve the stability and adapt to complex external environment. You can use Bivocom standard power adapter(12VDC/500mA), or use DC power ranging at 5-35VDC, please make sure the power supply is stable enough(Ripple shall be less than 300mA, and Instantaneous voltage shall not larger than Addr.: Unit 704, No. -
Page 11: Led Indicators
System works System doesn’t works Blink 4. Serial Port Configuration Connect TW810 to your laptop or computer through RS232, then open Bivocom configuration tool (TW810.exe), Click on the left side, choose the right serial port as below, Addr.: Unit 704, No. A3 Building,... -
Page 12: Operations
Check the version info of TW810. 4.1.5 Signal Value Check the signal strength of TW810. 4.1.6 Factory Setting TW810 returns to factory setting. Addr.: Unit 704, No. A3 Building, Tel: +86-592-6211770 Software Park, Xiamen, China 361000 Fax: +86-592-6211727 www.bivocom.com sales@bivocom.com... -
Page 13: Restart
Save configuration of TW810 in file format, which you can use it recover the config. 4.1.9 Configure via Saved Config File Click , and choose the saved config file, then click to configure TW810. 4.2 Basic Setting Addr.: Unit 704, No. A3 Building, Tel: +86-592-6211770 Software Park, Xiamen, China 361000 Fax: +86-592-6211727 www.bivocom.com sales@bivocom.com... -
Page 14: Device Id
There are 3 levels to choose from the drop-down menu, as below 2: All logs output through RS232/RS485 1: Part of important logs output through RS232/RS485 0: No logs output Addr.: Unit 704, No. A3 Building, Tel: +86-592-6211770 Software Park, Xiamen, China 361000 Fax: +86-592-6211727 www.bivocom.com sales@bivocom.com... -
Page 15: Communication Baud Rate
When NB-IoT Modem receives packet slicing, increase the value, while for packet merging, lower the value, 20ms for 115200 baud rate, 50ms for 9600 baud rate and 200ms for 1200 baud rate. Addr.: Unit 704, No. A3 Building, Tel: +86-592-6211770 Software Park, Xiamen, China 361000 Fax: +86-592-6211727 www.bivocom.com sales@bivocom.com... -
Page 16: Trigger Settings
DATA:Sending specific data to trigger TW810 online or offline. Note: SMSD, CTRL, MIXED are not applicable to TW810, only available on TD210 Cellular modem. http://www.bivocom.com/index.php?m=content&c=index&a=show&catid=12&id=22 2) Data Trigger On Password You can set up trigger data in the blank, once the trigger mode is DATA and MIXD, and TW810 receives the trigger data through RS232/RS485 serial port, it will get online. -
Page 17: Networking Setting
TW810 will act as a UDP client when choose NUDP. Note: To save the power consumption, NB-IoT Modem TW810 only supports UDP. Addr.: Unit 704, No. A3 Building, Tel: +86-592-6211770 Software Park, Xiamen, China 361000 Fax: +86-592-6211727 www.bivocom.com sales@bivocom.com... -
Page 18: Data Center Number
It can be configured as DNS or IP address. 3) Center DNS Server When you use DNS for center, a DNS server is required to analytic the corresponding IP address. Addr.: Unit 704, No. A3 Building, Tel: +86-592-6211770 Software Park, Xiamen, China 361000 Fax: +86-592-6211727 www.bivocom.com sales@bivocom.com... -
Page 19: Dialing Settings
‘Y’, TW810 will check whether main center is recovery or not, if yes, it will switch to main center, and disconnect with backup center. While if choose ‘N’, TW810 will not check whether main center is recovery or not. Addr.: Unit 704, No. A3 Building, Tel: +86-592-6211770 Software Park, Xiamen, China 361000 Fax: +86-592-6211727 www.bivocom.com sales@bivocom.com... -
Page 20: Custom Register String
We suggest you keep it as default settings, as it is not supported by TW810. 4.3.10 Multi Center Reconnect Interval Only available when data center number is 2-5. Addr.: Unit 704, No. A3 Building, Tel: +86-592-6211770 Software Park, Xiamen, China 361000 Fax: +86-592-6211727 www.bivocom.com sales@bivocom.com... -
Page 21: Reconnect
It’s a reserved feature, we suggest you keep it as default settings, as it is not supported by TW810 now. 4.5 MODBUS Setting Modbus is a reserved feature, and not supported by TW810 now. 5. Firmware Upgrade 5.1 Please open the Bivocom Config Tool, as below, 1) Configure Serial Port parameters Baud Rate: 115200 ... - Page 22 5.2 Power on the TW810, then device will start to upgrade the firmware, as below 5.3 After firmware upgrading successfully, it shows ‘download success ok’, as below Addr.: Unit 704, No. A3 Building, Tel: +86-592-6211770 Software Park, Xiamen, China 361000 Fax: +86-592-6211727 www.bivocom.com sales@bivocom.com...
- Page 23 5.4 Then use the Config Tool to enter into the configuration status, set up the device to factory setting, and restart to configure the parameters. Addr.: Unit 704, No. A3 Building, Tel: +86-592-6211770 Software Park, Xiamen, China 361000 Fax: +86-592-6211727 www.bivocom.com sales@bivocom.com...
-
Page 24: Appendix 1: At Command
Center Port AT+PORT1=XX XX: 2 Center Port Center Addr. AT+IPAD2=XX XX: 3 center IP address or Center Port AT+PORT2=XX XX: 3 Center Port Addr.: Unit 704, No. A3 Building, Tel: +86-592-6211770 Software Park, Xiamen, China 361000 Fax: +86-592-6211727 www.bivocom.com sales@bivocom.com... - Page 25 SMS Send Phone No. AT+PHONE2=XX XX: Use comma for multi phone number SMS Send Phone No. AT+PHONE3=XX XX: Use comma for multi Addr.: Unit 704, No. A3 Building, Tel: +86-592-6211770 Software Park, Xiamen, China 361000 Fax: +86-592-6211727 www.bivocom.com sales@bivocom.com...
-
Page 26: Appendix 2: Faq
4) Check if the SIM is out of service (charges owed) and function of data is on. 3. The device couldn’t enter into configuration mode. Check the connection of RS232/RS485 is correct. Addr.: Unit 704, No. A3 Building, Tel: +86-592-6211770 Software Park, Xiamen, China 361000 Fax: +86-592-6211727 www.bivocom.com sales@bivocom.com... - Page 27 Is the RS232/RS485 connected to your computer or laptop and serial port of computer or laptop is working. Check whether the baud rate of computer or laptop is the same as NB-IoT Modem. Addr.: Unit 704, No. A3 Building, Tel: +86-592-6211770 Software Park, Xiamen, China 361000 Fax: +86-592-6211727 www.bivocom.com sales@bivocom.com...
Need help?
Do you have a question about the TW810-B5 and is the answer not in the manual?
Questions and answers