Related Manuals for Efitment E006
Summary of Contents for Efitment E006
- Page 1 E006 MAGNETIC ELLIPTICAL BIKE USER MANUAL IMPORTANT! Read all instructions carefully before using this product. Save this user manual for future reference. For customer service, contact: service@efitment.com...
-
Page 2: Important Safety Notice
IMPORTANT SAFETY NOTICE Note the following precautions before assembling and using the machine. 1. Assemble the machine exactly as described in the instruction manual. 2. Check all the bolts, nuts and other connections before using the machine for the first time to ensure the machine is in the safe condition. -
Page 3: Exploded Diagram
EXPLODED DIAGRAM... -
Page 4: Parts List
PARTS LIST Q’TY Q’TY DESCRIPTION DESCRIPTION Main frame Hex screw M8x55 Handlebar post Flat washer D8x1.5 Front Stabilizer Nylon nut M8 Rear Stabilizer Hex bolt M10x45 5L/R Pedal support 1pr. Flat washer D10x1.5 6 L/R Swing tube 1pr. Nylon nut M10 7 L/R Handlebar 1pr. -
Page 5: Hardware Package
It is strongly recommended this machine to be assembled by two or more people to avoid possible injury. HARDWARE PACKAGE... -
Page 6: Assembly Instruction
ASSEMBLY INSTRUCTION STEP 1 Attach the Front Stabilizer (3) and Rear Stabilizer (4) to the Main Frame (1) with the Carriage Bolts (12), Spring Washers (52), Arc Washers (13) and Acorn Nuts (14) as shown. - Page 7 STEP 2 A: Connect the Extension Wire (18) with the Sensor Wire (20) together. Check the Tension Controller (17) is at Level 8 to ensure the cable is the longest. Put the cable of Tension Controller (17) into the spring hook of Tension Wire (19) as picture A shows.
- Page 8 STEP 3 Attach the Left Swing Tube (6L) to the shaft on Handlebar Post (2) with Hex Screw (24), Spring Washer (52), Flat Washer (25), Wave Washer (54) and Long Axle (27). Don’t tighten them yet. B: Attach the Left Pedal Support (5L) to the Crank (22) with Left Pedal Bolt (38L), Wave Washer (45).
- Page 9 STEP 4 A: Feed the Pulse Wire (50) out of the Handlebar Post (2) through the top of the computer bracket. B: Attach the Handrail (8) to the Handlebar Post (2) with Allen Pan Bolt (51)，Spring Washer (52). Then, cover with the Chuck Cover (53). C: Attach the Handlebar (7L/R) to the Swing Tube (6L/R) with Allen Screw (16), Spring Washer (52) and Arc Washer (44).
- Page 10 STEP 5 A: Remove Cross Pan Screws (55) from the back of the Computer (9). Connect the Extension Sensor Wire (18) and Pulse Wire (50) with wires of Computer (9) and then fix the Computer (9) to the bracket of Handlebar Post (2) with Cross Pan Screw (55).
- Page 11 Moving the Bike To move the elliptical, hold by the handles of the Handrail (8). Tilt the elliptical until the wheels of the Front Stabilizer (3) touch the floor. Then you can wheel the elliptical to the desired location.
-
Page 12: Key Functions
EXERCISE COMPUTER INSTRUCTIONS SPECIFICATIONS: TIME……………………………………………………….00:00-99:59 SPEED(SPD)..………………………………………… 0.0-99.9ML/H DISTANCE(DIST)………………………………………0.00-999.9ML CALORIE(CAL)…………………………………………0.00-9999KCAL ODOMETER(ODO)…………………………..………0.0-9999ML PULSE (PUL) ……...........0，40~240BPM KEY FUNCTIONS: MODE: Press to select a function SET: Press to preset value for “TIME”, “DISTANCE”, “CALORIES”, or “PULSE”. CLEAR(RESET): Press to clear the value OPERATION PROCEDURES: 1.
Need help?
Do you have a question about the E006 and is the answer not in the manual?
Questions and answers