Advertisement
Quick Links
Wingspan:
Length:
Flight Weight:
Model of known German fighter of World War II. It is one of the first version that appeared on the battlefields in the
beginning of the war and is known mainly from 'Battle of Britain "
Modular model aircraft is largely made of extruded polypropylene EPP. This material model provides considerable
resilience and durability. Model due to its characteristics allows a pleasant flying and demanding aerobatics or aerial
combat.
Model due to the material used, many will survive the crash without injury and, if damage is directly on the flight
patch area.
The model is largely prefinished and its completion will take little time. The model is not intended beginners,
because it is not in the instructions described in detail each operation. Construction and completion of the model
must adapt to the selected drive and practice builder.
List of construction work:
The hull of the EPP
Enclosure (transparent)
Half of the EPP wings
Helm of the EPP
Clutch elevator balsa
Plywood parts
The control lever
Ties kormidel
Plastic screw+ nut
Other necessary tools to build:
The second adhesive, activator of the second adhesives, polyurethane adhesive (Purex), epoxy, sharp knife
Suggested drive:
the series motor AXI 2808/24 or equivalent, controller 40A
Battery: 3S Li-pol 2200 mAh
Propeller: 9 / 5 - 10 / 5 "
Construction of the model:
Before the actual construction carefully study of the building instructions and prepare instruments for building.
Construction guidance is only a guide to building your own. The construction modifying presumption equipment and
mainly of own construction capabilities.
Bf-109E
Modular radio controlled aircraft model
1100 mm
960 mm
700-900 g
5 pcs
1 pc
2 pcs
2 +2 pc
4x 10 mm
5 pcs
3 pcs
1 + 2 pc
1 + 1 pc
Advertisement
Summary of Contents for LM model Bf-109E
- Page 1 Bf-109E Modular radio controlled aircraft model Wingspan: 1100 mm Length: 960 mm Flight Weight: 700-900 g Model of known German fighter of World War II. It is one of the first version that appeared on the battlefields in the beginning of the war and is known mainly from 'Battle of Britain ”...
- Page 2 brushless motor AXI 2814/16 controller elevator servo battery receiver rod elevator motor C.G. 66 mm bulkhead 1 servo wings 2 x pin Ø 4 mm Underside of the wings 60 mm carbon tape 80 mm Top of the wing 66 mm plywood Elevator...
- Page 3 Fixed part of elevator cut across On the floating part of the elevator and add carbon tape 8x 0,3 mm. stick reinforcements from balsa 8x4 seříznout The reinforcements of carbon Slice off the leading edge in the paste by second glue "V"...
- Page 4 Attach the Real part of the cab. Cut off the buttom of the mddle part of fuselage. Stick plywood front and rear portion for mounting wings. For sealing the front portion of plywood make slit in A sharp knife cut a groove to insert a the hull.
- Page 5 Instead of sticking to the cooler models 70 mm cut off this part of 60 mm carbon tape It cut across aileron Cut and hollow out a hole for the servo. Cablet servo Carbon tape seal sparse sekond glue. add to notch in the wing. Cut wings in the spot labeled.
- Page 6 Stick models coolers Cut down center of the wings and stick plate for mounting bolt. In the prepared hole paste and stick up plastic nut. Cut out notches for the hinges. Cut out notch for the kontrol lever and the lever stick up. Glue the rear of the fuselage.
- Page 7 Compile and stick together a motor wicket. Before stick a motor wicket cut groove for the engine cables. .On the front of hull stick on a motor wicket. Cut out a notch and stick up control lever of wings. Rod made of steel wire 0, 8 mm. .Set together rudder, stick elevator hinges.
- Page 8 On the front part of the fuselage stick models of In the pre-prepared hole install exhaust pipes and heatsinks. the rod elevator. On the front part of the fuselage stick Trim cab and stick surround. models of exhaust pipes and heatsinks Equipment of the model dislocated so that it After painted of model cab stick to the hull.
- Page 9 Model colorful by adulterate color acrylic paints. Color lay on by roller or brush. Paintbrush apply rougher bristles to get the color to the pores. Alternatively, you can lay on the color by spray gun. Before the first flight, check the position of center of gravity, which modify by accumulators. Scale kormidel set to start at about 20-30 °...