Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for UniFlow microMIND V2
Summary of Contents for UniFlow microMIND V2
- Page 1 V2 Installation Guide...
- Page 2 Therefore of Therefore™ UNIX® of The Open Group uniFLOW OM®, uniFLOW™, uniFLOW Serverless Secure Printing®, MIND®, microMIND®, and MiCard® are registered trademarks of NT-ware Systemprogrammierung GmbH All other trademarks, trade names, product names, service marks are property of their respective owners and are hereby acknowledged.
-
Page 3: Symbols Used In This Manual
V2 Installation & Configuration Publisher NT-ware Systemprogrammierung GmbH Symbols used in this manual: Technical Editors Marja Pals Note Printer Wizard Lydia Abghay Publisher Elk e Witt NT-ware Systemprogrammierung GmbH Thomas Lemmer Important Settings Note Team Coordinator Technical Authors Claudia Kleinek emper... -
Page 4: Table Of Contents
Table of Contents Foreword Document Versioning Information microMIND V2 Introduction Scope of supply Technical Specifications FCC and IC Compliance Note Installation LED Status Configuration Configurable param eters ................................. 10 2.7.1 Code Conversion ..............................11 2.7.1.1 microMIND V2 Website Firmware update 2.10... -
Page 5: Document Versioning Information
Document Versioning Information... - Page 6 Version: Revision date: Reviewer: Final Review: Technologies concerned: microMIND V2 File name: microMIND_V2_installation_manual_EN.pdf Short Summary: This manual describes the features, the installation, and the configuration of the microMIND V2 in detail. microMIND V2 is a registered trademark of NT-ware Systemprogrammierung GmbH.
-
Page 7: Micromind V2
V2... -
Page 8: Introduction
V2. This can be required for network printers. Note that the microMIND V2 does not have to be attached to the printer. It only transfers the ID data, reads from the users ID card, to the uniFLOW Server and thus tells the uniFLOW Server to release the print jobs for this user. - Page 9 V2 (only secure printing - without copy accounting) microMIND connected to a uniFLOW printer for secure printing only microMIND V2 (secure printing and copy accounting / device locking) microMIND connected with a copy accounting cable to lock the MFD...
-
Page 10: Scope Of Supply
The microMIND V2 is available in two different versions. One Power Supply: with PoE (Power over Ethernet) and one without. If you have a microMIND V2 which does not support PoE or if your network switch does not support PoE, you have to use the respective power supply. -
Page 11: Fcc And Ic Compliance Note
Status LEDs: Note that the MiCard (V1) and MiCard V2 readers are the only readers supported by the microMIND V2. Do not attach different readers or USB devices to the microMIND V2. Changes and/or modifications of the microMIND V2 not approved by NT-ware Systemprogrammierung GmbH will invalidate the user’s authority to operate... -
Page 12: Installation
6. Attach the microMIND V2 reader to the network. 7. Plug-in the power supply of the microMIND V2 if required. This is necessary if you have no PoE microMIND V2 or if you have a PoE microMIND V2 but your network doesn't support PoE. -
Page 13: Led Status
V2 - Installation Guide LED Status The microMIND V2 is equipped with two status LEDs. The tables below show the status information given by the respective LED. Power LED: Status/Color Status description No power supplied or boot loader phase (see also chapter... -
Page 14: Configuration
Connections / Agents/Terminals / MIND & microMIND and select the List view page. In this screen you can see the status information of the attached MINDs / microMINDs / microMIND V2. The column Type shows you if it is a MIND (MindNet Device) or a microMIND V2. -
Page 15: Code Conversion
The microMIND V2 IP configuration can be found by selecting a microMIND V2 via mouse click on the IP address. You’ll find the serial number of the respective microMIND V2 on a sticker on the back of the microMIND V2. A browser screen will open to configure the microMIND V2 IP address. -
Page 16: Micromind V2 Website
The microMIND V2 site gives information about the following: Serial Number This is the serial number of the microMIND V2 itself. It is used to select a microMIND V2 during a printer configuration. You will also find this number on a sticker on the back of each microMIND V2. - Page 17 Shows the last ID of a read out authentication card without code conversion (raw data). Name You can change the default name microMIND V2 for an easier identification of the device itself, for example the name of the associated printer.
- Page 18 MiCard V2 HID: use extended data Tick this parameter if you are using the MiCard V2 HID with SSP (Serverless Secure Printing). Leave it disabled in a normal uniFLOW environment. Upload USB HID configuration file Here you can upload specific USB Human Interface Device Reader configuration files (Key Files).
- Page 19 V2 - Installation Guide...
-
Page 20: Firmware Update
Format your USB stick according to the requirements listed above. Copy the MMAPP file onto the USB stick. Detach your microMIND V2 from the power supply. If PoE is used, detach the network connection. Attach the USB stick to the microMIND V2. - Page 21 ©2012 microMIND V2 is a registered trademark of NT-ware Sy stemprogrammierung GmbH...
Need help?
Do you have a question about the microMIND V2 and is the answer not in the manual?
Questions and answers