Receiving, Store And Moving The Units; Installation Accessories - Eden CS/4S 21 Installation, Operation And Maintenance Manual

water cassettes
WARNING!
- Disconnect the mains power supply switch before servicing the system
or handling any internal parts of the unit.
- The manufacturer declines any liability for damage resulting from modi-
fi cations or errors in the electrical or water connections.
- Failure to observe the installation instructions, or use the unit under
conditions other than those indicated in table "Operating limits" of this
manual, will immediately invalidate the unit warranty.
- Failure to observe electric safety codes may cause a fi re hazard in the
event of short circuits.
- Do not install or use damaged units.
- In case of malfunction turn the unit off, disconnect the mains power sup-
ply and contact a qualifi ed service engineer.
- Maintenance must only be carried out by qualifi ed personnel.
- All of the manufacturing and packaging materials used for this appliance
are biodegradable and recyclable.
- Dispose of the packaging material in accordance with local require-
ments.

RECEIVING, STORE AND MOVING THE UNITS

At the moment of the delivery of the unit, make sure that it corresponds to the
one indicated on the transport document. Check the integrity of the packing
and the unit. Should there be any differences with the original order or any
damages, anomalies, or incomplete supply, please point it out on the delivery
note and inform the fi rm straight away. Never install or use damaged appara-
tuses. The unit can be stored in room protected from bad weather with tempe-
rature between the -20°C and the +55°C. Transport the packed unit near as
possible to the installation place. To avoid any damage to the unit, the plastic
part (frontal panel and grille) are furnished separately. The handling and the
installation could be facilitated cy use of an elevator (Pic. 05).
ATTENTION!
Catch up the cassette on the four corners.
Don't lift or move the unit through the ex-
changer pipelines or the exhaust pipe con-
dense.

INSTALLATION ACCESSORIES

Vengono inclusi nella fornitura i seguenti materiali per l'installazione:
- n. 1 Cardboard mounting template;
- n. 1 Secondary basin for the condensation to be collected in correspondence
with the valves.
SELECTION OF CASSETTE INSTALLATION LOCATION
RECCOMENDATION!
- The unit must be installed in a solid and vibration-free ceiling.
- There should be no obstruction of the air fl ow into and out of the unit and the
air should be evenly distributed throughout the whole room.
- Do not install the unit near sources of heat, steam or infl ammable gases.
- Install the unit near an electric socket or connect it directly to the power
supply.
- Do not install the unit in a place, which is exposed to direct sunlight.
- The selected place should allow easy drainage of the condensed water.
- Periodically check appliance operation and leave suffi cient space for mainte-
nance around the appliance, as shown in the picture 06.
- Install the unit so that the fi lter is easily accessible.
INSTALLATION
FIXING THE CASSETTE
Select a place of installation where there can be a clearance of a least 100 cm
(see pic. 06) around the appliance. Make sure that the installation does not
interfere with existing electric wiring or plumbing.
Vers. 2009-3
Establish the position and size of the hole in the ceiling using the external dia-
meter of the cardboard mounting template (pic. 07).
To fi x the unit to the ceiling, use the threaded bar and suitable screw anchors as
shown in pic. 08 (material not included in the supply).
A
C
Use a spirit level (pic. 9) to make sure that the unit is level and check that it is
securely fi xed to the ceiling. In high humidity environments, metal supports must
be insulated using adhesive insulating material.
Pic. 05
FIXING THE PANEL
After installation of the unit, mount the grille using the 4 screws provided
(pic. 10).
ATTENTION: It is very important to fi x the grille in the right position for
correct connection of the receiver panel to the unit.
- to fi x the panel only use the four supplied screws.
Do not use other kinds of screws or you could damage the condensate
drain pan.
- Do not bend or narrow the unit piping.
- Do not remove the cap from the unit piping until immediately before connecting
the pipes.
- To prevent deformation of the air intake grille, do not overtighten the screws.
7
INSTALLATION, OPERATION
AND MAINTENANCE MANUAL
>100
Pic. 06
Pic. 07
B
D
Pic. 08
Pic. 09
Pic. 10