Related Manuals for Ratoc Systems MR18
Summary of Contents for Ratoc Systems MR18
- Page 1 Professional Media Card Reader/Writer Unit with USB3.0 MR18 MR18EX User’s Manual Dec. 2016 Rev1.1 MR18EX SD Card SD UHS- II SATA Compact Flash MR18...
- Page 2 ３．RATOC Systems, Inc. doesn’t take responsibility for any damage arising from the use of this product. ４．This publication may not be reproduced or used in whole or in part without permission of RATOC Systems,Inc. ５．Design and specifications are subject to change without notice.
-
Page 3: Table Of Contents
Contents Introduction １ 1-1.Package Contents －－－－－－－－－－－－ 4 1-2.System Requirement －－－－－－－－－－－－ 5 1-3.Supported media －－－－－－－－－－－－ 5 1-4.Description of each part －－－－－－－－－－－－ 6 Setup 2-1.Procedure to install this product －－－－－－－－ 8 2-2.Connection of a USB －－－－－－－－－－－－ 8 2-3.Installation of HotPlug tool and how to use it －－－ 9 2-4.Direction of each media insertion－－－－－－－－－... -
Page 4: １ Introduction
1-1-1.MR18 USB cable SD Car d 2 SD Car d 1 Standard-A - Micro-B SAT A Compact F la sh Sx S 2.95ft(90cm) MR18 body CD-ROM Warranty Card 1-1-2.MR18EX USB 3.0 cable Standard-A - Standard-B 2.95ft(90cm) Power cable MR18EX body... -
Page 5: 1-2.System Requirement
-2.System Requirement １ ●Supported OS ：Windows10 / 8.1 / 7 ※Compatible with both 64bit and 32bit OS Mac OS X 10.10 or later ●Supported PC ：WindowsPC with USB3.0/2.0 ports(It is recommended to connect USB3.0 ports) Mac with USB3.0/2.0 -3.Supported media １... -
Page 6: 1-4.Description Of Each Part
-4.Description of each part １ 1-4-1.MR18 ●Front panel UHS-II compatible SD card slot, SD card slot, access LED access LED CF card slot, access LED SSD slot, access LED SxS slot, access LED ※If you use a UHS-II compatible SD card, be sure to use the SD card slot at the right side. - Page 7 1-4-2.MR18EX ●Front panel Each part of memory card is the same as MR18, as described in the previous page. PowerLED Power switch ※If you use a UHS-II compatible SD card, be sure to use the SD card slot at the right side. If you use the SD card slot at the left side, access speed will be down.
-
Page 8: Setup
-2.Connection of a USB cable 2-2-1.Connection of MR18 ●It is required to install MR18 into a 5 inch bay of a PC. For further information, please refer to the User’s Manual which accompanies a PC, PC case. ●Attach the bundled USB cable into the Micro-B connector of MR18. -
Page 9: 2-3.Installation Of Hotplug Tool And How To Use It
If you use MR08 or MR08EX with the PC currently, be sure to uninstall its HotPlug tool before installing the HotPlug tool for MR18/MR18EX. ●Before installation of Hot-Plug tool, confirm MR18/MR18EX is connected to the PC. And then, start [ REX-MRHotPlugTool-Setup.exe] at the bundled CD-ROM and follow the on-screen instructions to finish installation. - Page 10 2-3-2.Confirmation of the installatioon of the HotPlug tool ●If the below screen appears, MR18/MR18EX isn’t recognized correctly. In this case, finish the installation first. And then, connect MR18/MR18EX. After confirming MR18/MR18EX is recognized correctly, start [ REX-MRHotPlugTool-Setup.exe] at the bundled CD-ROM and follow the on-screen instructions one more time.
- Page 11 Black：Media slot with media 2-3-3.How to use HotPlug tool ●Click the icon at bottom right. ●Black letters mean media which are inserted into the slot now. Gray letters mean media which aren’t inserted into the slot now. ●If you click a media you want to remove, it will be ready for removal.
-
Page 12: 2-4.Direction Of Each Media Insertion
-4. Direction of each media insertion ●Be careful of direction of media insertion when each media is inserted. Caution ●If media is inserted in the wrong direction, media or MR18/MR18EX may have damaged. ●SD Card (For both SD UHS-II slot and SD Card slot) ＋Insert SD card with the SD label facing up. -
Page 13: Drive Letters
Drive letters ●A drive letter in each media slot will be assigned automatically by Windows after installation of MR18/MR18EX. If drive letters aren’t used, a user can assign any drive letter by following the next steps. ●Once the setting is made, Windows will keep the setting, and when Windows starts next time, the assigned drive letter can be used. -
Page 14: 3-3.Windows7
-3.Windows7 ●Right-click at [Computer] and click [Manage]. ●Click [Disk Management] at the [Computer Management] window. ●Right-click at a drive you want to change, and click the [Change Drive Letter and Paths...]. ●Select the drive letter and click [Change]. ●Allocable drive letter will be shown. Select a drive letter and click [OK]. Page.14... - Page 15 ●The warning window will appear. Click [Yes]. ●Drive letter changed to the one you selected. Page.15...
-
Page 16: Installation And Confirmation Inmac Os
MacOS X(10.10 or later) will load driver software automatically once MR18EX is connected to Mac. Select [System information] – [USB]. The screen shown below will appear. This screen shows MR18EX. [MR18(SATA-HDD)] appears only when SSD is recognized. Page.16...