Download
Share
Print this page
AutoAnchor AA570 Owner's Manual
  1. Manuals
  2. Brands
  3. AutoAnchor Manuals
  4. Marine Equipment
  5. AA570
  6. Owner's manual

AutoAnchor AA570 Owner's Manual

Remote console and base station
Hide thumbs

Advertisement

Quick Links

Download this manual
AutoAnchor 570

Advertisement

loading
Need help?

Need help?

Do you have a question about the AA570 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for AutoAnchor AA570

Summary of Contents for AutoAnchor AA570

  • Page 1 AutoAnchor 570...

  • Page 3: Table Of Contents

    The documentation relating to the AutoAnchor products is created in the English language and may be translated from English to another language. In the event of any conflict between translated documents, the English language version will be the official version.

  • Page 4: Part 1 Important Information

    The AA570 can be fitted to most vertical windlasses. A horizontal windlass may require a sensor holder or a custom designed sensor which is not included in the standard pack. Check with your supplier or the AutoAnchor manufacturer. • The AA570 must be fitted to a windlass with a dual direction control box or solenoid pack. • Information for installation and operation of the AA570 is supplied, including pre-set windlass profile lists, wiring diagrams, the Owner’s Manual and the Quick User Guide. All documents must be left on board for the owner.
  • Page 5 DC windlasses require a dual direction solenoid Tips For Optimal Wireless Connectivty AA570 equipment (AA702 base station, AA710 remote and AA570 console) must be installed least 3ft (1m) away from any equipment transmitting or cables carrying radio signals eg VHF radios, modified sine wave inverters, cables and antennas or radar antennas; and at least 6ft (2m) away from any SSB equipment.
  • Page 6 Note: If shielded cable is not used for the sensor connections this will compromise the EMC and may invalidate the warranty. AA570 equipment (AA702 base station, AA710 remote and AA570 console) must be installed least 3ft (1m) away from any equipment transmitting or cables carrying radio signals eg VHF radios, modified sine wave inverters, cables and antennas or radar antennas;...

  • Page 7: Part 2 Installation

    (all-chain or rope and chain). Please follow the instructions for your windlass and rode. If it is not possible to comply with these instructions please check with the AutoAnchor manufacturer or your supplier for other options or if you are not sure how to proceed.
  • Page 8 Sensor Plug 2.1.4 PLUG ANd PLAy SENSOR CABLE The AutoAnchor plug and play sensor cable is 2 core tinned shielded cable. It must be used to connect the sensor to the console unit. Ensure the connectors are firmly screwed together.
  • Page 9 3mm and a maximum of 5mm. This sensor requires a field connector. The AutoAnchor will operate with a reed switch sensor for all-chain rode. If using combination rope and chain rode the reed switch sensor provides a reasonably accurate count of rode deployed but on retrieval the display may be incorrect because it cannot allow for the stretch in the rope.
  • Page 10 2.1.7 INSTALLATION ON A VERTICAL WINdLASS - CHAIN ONLy Refer to the Overview Notes on page 4 before starting installation. Chainwheel Note: If it is not possible to Magnet align the sensor and magnet exactly the AA grey sensor may Seal with minimum 1mm epoxy.
  • Page 11 Sensor Position: The AutoAnchor sensor may be fitted using a sensor holder fixed to the deck to sit under the chainwheel (See Fig 6). The AutoAnchor sensor holder (#9070) is not included in the standard kit. Check with your supplier if you need this. The AA black sensor and the reed switch sensor must be fitted directly in line with the magnet in the chainwheel.
  • Page 12 2.1.10 INSTALLATION ON A HORIZONTAL WINdLASS - ROPE & CHAIN Before starting check with the AutoAnchor manufacturer, or supplier, that it is possible to fit the sensor and magnet to your horizontal windlass. For an accurate rope count the rode must run between the sensor and magnet. On a horizontal windlass the magnet and sensor must be fitted by the windlass manufacturer.
  • Page 13 2.4 REMOTE CONSOLE ANd BASE STATION INSTALLATION AA570 kit has one master base station and one remote console. Each base station has 6 outputs. Up to 2 slave stations can be attached to the master station to provide extra outputs.
  • Page 14 2.4.2 CONSOLE INSTALLATION The console is supplied with mounting kit and a cover. One remote console can operate multiple base stations. The unit should be mounted on a flat surface at least 3ft (1m) away from any equipment transmitting or cables carrying radio signals eg VHF radios, cables and antennas or radar antenna and at least 6ft (2m) away from any SSB equipment.

  • Page 15: Power Supply

    Power supply to the AA702 base station must be from the windlass control circuit, along with all other windlass controls eg. toggle switch, remote switches, deck switches, other AutoAnchor devices. Power supply must not be from the motor positive near the windlass.
  • Page 16 5 and 6 can be used for other options. 2.7.2 MULTIPLE AUTOANCHOR INSTALLATIONS It is important when wiring multiple AutoAnchor products that potential differences do not occur along the ground connection. This can cause incorrect counting. Ensure AA560 and AA150 consoles and AA702 base stations are star grounded, and that there are no other high current paths between consoles.
  • Page 17 (See the photograph below). Tighten the cable gland. Replace the lid. 2.7.6 WIRING dIAGRAMS FOR AA702 BASE STATION Wiring diagrams are included in the kit. Please refer to them for wiring detail. These diagrams and installation help are also available on www.autoanchor.co.nz...

  • Page 18: Part 3 Set Up

    3.2 WIRELESS INTERFACE SET UP 3.2.1 SySTEM OVERVIEW The AA570 kit is supplied with 1 x AA570 remote console and 1 x AA702 master base station. Each console and base station has a unique ID and the units must be registered to each other to operate the system.
  • Page 19 Power button to turn on the remote console. The screen will tell you to “Press the register switch on the master base station”. NB. On first use AA570 will be on already. 5. Press and release the registration button. The green LED will stay on.
  • Page 20 0D Slave Station 2 ID ______________ Note: The AA570 console will automatically update and register the additional slave station when it is next turned on. 3.2.8 dEREGISTERING A BASE STATION f a base station is removed or replaced it must be deregistered from the system. To do this: Turn the power off to the affected base station and disconnect it.
  • Page 21 3.2.9 REGISTERING A PREVIOUSLy USEd BASE STATION OR CONSOLE ALL SETTINGS MUST BE CLEAREd Previously Used Base Station Turn off all existing base stations and consoles. Turn on the power to the used base station only. Hold down the registration button for 15 seconds until all three LED’s flash. This indicates the base station has performed a complete factory reset and all settings have reverted to the defaults.
  • Page 22 3.3 SET UP MENU OvERvIEw The AutoAnchor must be turned off to access the Set up menu. Hold together to display the Set up menu. to scroll through the menu. GENERAL WIRELESS CHANNEL WINdLASS GENERAL WINdLASS RESET REGISTRATION Language docking distance...
  • Page 23 3.4 MOdES SET UP The AA702 base station must be powered up to access AA570 Set up Menu. AA570 system can be set up to operate your choice of equipment on the boat. The standard kit has one master base station and one console. Each base station has 6 outputs.
  • Page 24 3.3 GENERAL SET UP To Access General Set Up Turn the AutoAnchor Off. Hold together to display the Set Up menu. Select General. To Exit General Set Up Exit to the Set up menu or hold for 2 seconds to exit to the start screen.
  • Page 25 3.5 wINdLASS SET UP For accurate counting you must set up the AutoAnchor with information for your windlass. Record the settings for future reference. 3.5.1 To Access windlass Set up Turn the AutoAnchor Off. Turn the AutoAnchor Off. Hold together to access the Set up menu.
  • Page 26 0.875 3.7 ROPE ANd CHAIN ROdE SET UP Some rope and chain windlasses have the settings already entered in the AutoAnchor. Refer to the Preset Windlass Profile List in Appendix 1. If your windlass is on the list select “Use preset” to enter the Windlass profile.
  • Page 27 3.7.1 Selecting Use Preset Setting: Refer to the Preset Windlass Profile List list in Appendix 1. Select Use Preset. Select Preset. Scroll to the correct Windlass profile for your windlass. Save and return to Windlass Set up. There are no further settings.
  • Page 28 Some operators prefer to use the buttons so that = Out and = In Access the swap controls feature via the Windlass Set up Menu. Turn the AutoAnchor Off. Hold together to access the Set up menu. Scroll to Windlass. Select Windlass Select Windlass.
  • Page 29 Total Rode Length. Inside Diameter. Outside Diameter with rode retrieved. 3.10.1 To Access windlass Set up Turn the AutoAnchor Off. Turn the AutoAnchor Off. Hold together to access the Set up menu. Scroll to Windlass. Select Windlass. Select Windlass.

  • Page 30: Part 4 Operation

    Hold the Mode button for 2 seconds to unlock. The lock automatically resets 5 minutes after the AutoAnchor was last operated or when the AutoAnchor is turned off. You can also reset the lock by holding down the button until the key is displayed in the top right corner.
  • Page 31 4.3 USER PRECAUTIONS It is the owner’s sole responsibility to ensure the AutoAnchor is installed, used and maintained in a manner that will not cause accidents, personal injury or property damage. When using the AutoAnchor the operator must follow safe boating practices for all equipment use.
  • Page 32 4.4 SET UP ANd TESTING Before use the AutoAnchor must be correctly set up for the equipment it is to control and then tested in a safe environment. For example, the AutoAnchor will not count correctly if the windlass selection is wrong or the windlass is not standard (eg it is installed with a different chainwheel or motor).
  • Page 33 4.4.2 AUTOMATIC OPERATION wARNING: There is an inherent risk when using any automatic function on a boat. If you choose to use the AutoAnchor automatic functions, you must still control and supervise all windlass and anchoring operation. Use the Automatic Function to: •...
  • Page 34 Safety Override Press any button on the AutoAnchor to stop the windlass during automatic release or retrieval. In an emergency shut off the power to the windlass using the isolating/ breaker switch. Enable Automatic Operation A “rode to be released” value must be entered to use automatic operation.
  • Page 35 Logs are cleared using the Factory Default Settings. Resetting the Factory defaults clears all logs and calibrations. 4.3.4 To Adjust Backlight The AutoAnchor must be turned on. It is best to change this setting in low light. Press to access the Menu. Select Backlight.

  • Page 36: Part 5 Maintenance

    PART 5 MAINTENANCE The AutoAnchor does not contain any user servicable parts. User maintenance is limited to: • Checking all cables and connections for signs of wear or damage and replacing them as necessary. • Checking the sensor head is not worn and has not moved out of alignment with the magnet and replacing the sensor if necessary. Afte any sensor repairs or changes to sensor installation reset the sensor. See page 28. • Checking the magnet is not worn or corroded and replacing the magnet if necessary. Note: Do not use chemical or abrasive materials to clean the console unit. If it is dirty wipe it with a clean damp cloth. Avoid wiping the display screen with a dry cloth as this could...

  • Page 37: Part 6 Troubleshooting

    PART 6 TROUBLESHOOTING Messages are displayed on the AA570 console screen to assist with operation and troubleshooting. These messages are designed to assist the user. They may be information messages, for example that the console is locked, or the sensor is tuning.
  • Page 38 2. Check the correct windlass set up and sensor has been selected. 3. Check the magnet and sensor installation. Note: The AA570 will 4. Check the magnet and sensor are not damaged (eg rusted continue to operate the magnet).
  • Page 39 WIRELESS NETWORK POSSIBLE CAUSE/ACTION TROUBLESHOOTING 1. Screen Message: Cannot 1. Turn all consoles and base stations off and then back on. Try register console and base registration again. If the problem persists: stations. 2. Clear registration for all consoles and base stations Try registration again.
  • Page 40 All wires must be connected (including the drain) and shielded cable must be used. 3. AutoAnchor counts but does not operate the Total length of rode has been set to off. windlass AutoAnchor then operates as a counter only.
  • Page 41 AutoAnchor. INTERNAL VOLTMETER/TEST TOOL: This tool displays the voltages and status of sensor, battery and load wires. The information is required by the AutoAnchor support team for effective technical assistance. Contact AutoAnchor support on: www.autoanchor.co.nz/autoanchor-installation-help Fill in the information form.
  • Page 42 Sensor Installation diagnostic Messages These messages appear when the AA570 is turned on. Go to the extended diagnostics for more information. After fixing the sensor installation retune the sensor. See page 28. Red sensor wire The Red sensor wire is overloaded below 2.5 volts...
  • Page 44 The AutoAnchor is designed and manufactured by: Kiwi Yachting Consultants Ltd PO Box 90114, Auckland Mail Centre, Auckland, New Zealand Ph: +64 9 360 0300 Email: support@autoanchor.co.nz AutoAnchor is a trademark of Kiwi Yachting Consultants Limited Copyright © 2013, Kiwi Yachting Consultants Limited, New Zealand AA570OWN...

This manual is also suitable for:

Aa702