Related Manuals for Axis 25734
Summary of Contents for Axis 25734
- Page 1 Product Instructions 25734 C O M M U N I C A T I O N S 81-IN6215 Before attempting to connect or operate this product, 06/01/07 please read these instructions completely.
- Page 2 IMPORTANT SAFEGUARDS 1. Read Instructions - All the safety and operating instructions should be read before the unit is operated. 2. Retain Instructions - The safety and operating instructions should be retained for future reference. 3. Heed Warnings - All warnings on the unit and in the operating instructions should be adhered to.
-
Page 3: General Instructions
ELECTRICAL SPECIFICATIONS (OUTDOOR ONLY): Power 24VAC, Class 2 Only 52 watts at 24 VAC (accessories) Heater: 50 watts Blower: 2 watts NOTE: This unit is designed for operation in an upright position. Installing the unit upside down may cause damage to the internal equipment, and will void the warranty. - Page 4 Installing the Axis 213 Camera 1. Install the camera onto the quick release bracket using (2) 10-32 x 3/8” screws and star washers provided in the packet. Attach cameras using these (2) holes 2. In the kit there are (8) aluminum spacers - (4) 1" and (4) ½".
-
Page 5: Camera Power
Installing Axis 213 Camera 4. Mount the camera assembly in the housing, sliding the (3) open screw slots over the (3) screws in the housing. Slide the bracket forward then tighten the captive screw on the bracket. (cont.) CAMERA POWER Connect the power plug and the ethernet cable to the back of the camera. - Page 6 Installing Axis 214 Camera Attach cameras using these (3) holes 1. Install the AXIS 214 camera to the 2685 mounting plate using the (3) 3mm x 12mm bolt and lock washers provided. 2. The AXIS 214 camera requires 1” of spacing for optimal position within the housing.
- Page 7 Installing Axis 231D/232D Camera 1. Install the camera onto the quick release bracket. Loosen one of the screws on the bottom of the camera, see diagram below. 2. Place quick release bracket onto the bottom of the camera, making sure that the (3) locking buttons line up with the keyhole slots in the Q/R bracket.
-
Page 8: Wiring Connections
Installing Axis 231D/232D Camera 7. Then start (3) 8-32x3/8” phillips head screws onto the (3) ½" spacers inside the housing. Be sure to place the screws so that they line up with the (3) open slots on the quick release bracket, the screws on the bottom of the camera, see diagram below. - Page 9 Installing Axis 231D/232D Camera (cont.) 11. To manage the input cable running from the connector block to the camera use the (2) cable tie mounts and cable ties that are located in the housing packet. Cable Tie Mounts Cable Ties 12.
- Page 10 Installing Axis 233 Camera 1. Note the position of the mounting holes on the camera bracket (see diagram below). Camera Bracket Mounting holes Mounting holes for housing 2. Since the 233 camera operates on 24vac, the power board that is located inside the housing is not needed. The remove the power board, start by loosening the screws on the terminal block and disconnect the orange and red wires.
- Page 11 Installing Axis 233 Camera 6. Mount the Axis 233 camera bracket and Q/R plate (Quick Release plate) as shown. Quick Release (Q/R) plate Keyhole Slots (cont.) 7. Place the Quick Release plate onto the bottom of the camera, Make sure that the locking screws on the AXIS 233 Keyhole Slots camera line up with...
-
Page 12: Installing The Housing Assembly
INSTALLING THE HOUSING ASSEMBLY: Be sure the bracket is properly and securely mounted to a supporting structure capable of rigidly holding the weight of the entire unit. NOTE: This unit is designed for operation in an upright position. Installing the product upside down may cause damage to the internal equipment, and will void the warranty. -
Page 13: Power Wiring
POWER WIRING Two plug-in wall transformers are included with the housing. Use one to provide power for the heater and blower in the housing, and the other for the camera. Determine where the transformers will be located, then run two sets of power wires into the wall mount bracket (Four total power wires). - Page 14 Replacement Parts List Part Number RPFD7015 FD7T FD7C RPFD703 RPFD072 RPFD080 RPFD060 RPRH707 RPFD040 RPFD709 RPFD711 Description Lower Trim Ring Tinted Replacement Capsule Clear Replacement Capsule Dome Clamping Bracket 24 Vac Heater (12 Vdc) Blower (Used In 24v Housings) Camera Bracket Connection Pcb Housing Hardware Housing Top...