Table of Contents
Advertisement
Quick Links
®
INSTALLATION, OPERATION,
& MAINTENANCE MANUAL
MRL-6000
SCISSOR LIFT
FOLLOW THIS MANUAL CAREFULLY TO ENSURE THE MACHINE WILL
FUNCTION CORRECTLY AND PROVIDE MANY YEARS OF DEPENDABLE SERVICE.
FAILURE TO FOLLOW THESE INSTRUCTIONS AND SAFETY WARNINGS MAY
RESULT IN PERSONAL INJURY OR PROPERTY DAMAGE. KEEP THIS MANUAL IN
A SAFE DRY PLACE FOR FUTURE REFERENCE.
1
Advertisement
Table of Contents
Related Manuals for Titan Lifts MRL-6000
Summary of Contents for Titan Lifts MRL-6000
- Page 1 ® INSTALLATION, OPERATION, & MAINTENANCE MANUAL MRL-6000 SCISSOR LIFT FOLLOW THIS MANUAL CAREFULLY TO ENSURE THE MACHINE WILL FUNCTION CORRECTLY AND PROVIDE MANY YEARS OF DEPENDABLE SERVICE. FAILURE TO FOLLOW THESE INSTRUCTIONS AND SAFETY WARNINGS MAY RESULT IN PERSONAL INJURY OR PROPERTY DAMAGE. KEEP THIS MANUAL IN...
- Page 2 Claims must be filed to cover cost. If you have any questions or if we can be of any further assistance, please don’t hesitate to contact a Titan Lifts® representative at 1-888-908-4826. Thank you for the opportunity to continue to serve your lift equipment needs.
-
Page 3: Table Of Contents
CONTENTS 1.Safety ..................1 1.1 Introduction ..................1 1.2 Safety Instructions for Commissioning ..........1 1.3 Safety Instructions for Operation ............1 1.4 Safety Instructions for Maintenance ............ 3 1.5 Risks ....................3 2. Unpacking & Set-up ............. 4 2.1 Delivery & check of packages ............. 4 2.2 Lifting &... -
Page 4: Safety
INSTRUCTIONS 1.SAFETY 1.1 INTRODUCTION WARNING: READ ENTIRE MANUAL AND COMPLY WITH ALL SAFETY AND SERVICE PRECAUTIONS. DEATH, PERSONAL INJURY AND / OR PROPERTY DAMAGE MAY OCCUR IF INSTRUCTIONS ARE NOT FOLLOWED CAREFULLY. Personal injury and property damage incurred due to non-compliance with these safety instructions are not covered by the product liability regulations. - Page 5 • Use caution when removing or installing heavy vehicle components which may result in center-of-gravity displacement. • Use this lift only for the work it is intended and only use Titan Lifts® recommended attachments. Do not use this product for an application for which it was not designed.
-
Page 6: Safety Instructions For Maintenance
1.4 SAFETY INSTRUCTIONS FOR MAINTENANCE • Maintenance or repair work should be done by authorized service personnel only. • Work on the electrical equipment by certified licensed electricians only. • Ensure that ecologically harmful substances are disposed of only in accordance with the appropriate regulations. -
Page 7: Unpacking & Set-Up
2. UNPACKING, & SET-UP Only skilled personnel who are familiar with the lift and this manual shall be allowed to carry out, lifting, handling, transport and unpacking operations. 2.1 DELIVERY AND CHECK OF PACKAGES When the lift is delivered, carefully unpack the lift making sure all the parts have been included. -
Page 8: Specifications
3. SPECIFICATIONS IMPORTANT: The properties indicated apply to lifts running at operating temperature. SPECIFICATIONS MRL-6000 Load capacity 6000 lbs. (2700kg) Raising / Lowering time Approx. 40sec. Minimum height 4-3/4” (12.1mm) Maximum lifting height 48-1/2” (123.2mm) / 54” (137.2mm) Operating temperature 41-131°F (5-55°C) -
Page 9: Floor Requirement
4. FLOOR REQUIREMENT These notes are for your guidance prior to installation 4.1 SELECTING THE SITE AREA Make sure that adequate space and height is available. 4.2 FLOOR REQUIREMENTS Do not use the lift on any asphalt surface. Make sure the lift is used on a dry, oil/grease free, flat level CONCRETE surface capable of supporting the weight of the lift, the vehicle being lifted, and any additional tools and equipment. -
Page 10: Installation Instructions
5. INSTALLATION INSTRUCTIONS IMPORTANT: THE HYDRAULIC HOSES HAVE BEEN PRE-INSTALLED FOR YOUR CONVENIENCE. BE CAREFUL NOT TO CUT THE HYDRAULIC HOSES DURING THE INSTALLATION PROCESS. 5.1 MOUNTING THE HYDRAULIC POWER UNIT/CONNECT HOSE ASSEMBLY 1. Attach the tow handle(1) to the pedestal(6) using the four(4) supplied attached bolts, washers, and nuts. -
Page 11: Electrical Connections
5.4 ELECTRICAL CONNECTIONS WARNING: ALL WIRING CHANGES MUST BE PERFORMED BY A CERTIFIED LICENSED ELECTRICIAN. THE STANDARD ELECTRIC MOTOR USED ON YOUR LIFT REQUIRES A 110-120 VOLT, 60HZ, SINGLE PHASE HOOK-UP. WARNING: DO NOT PERFORM ANY MAINTENANCE OR INSTALLATION OF ANY COMPONENTS WITHOUT FIRST ENSURING THAT ELECTRICAL POWER HAS BEEN DISCONNECTED AT THE SOURCE OR PANEL AND CANNOT BE RE- ENERGIZED UNTIL ALL MAINTENANCE AND/OR INSTALLATION PROCEDURES ARE COMPLETED. -
Page 12: Safety Lock Control
6.2.2 SAFETY LOCK CONTROL Press and hold the lowering handle (Fig.3) until the safety lock (30) is engaged the safety lock bar (33). Fig. 3 6.2.3 LOWERING CONTROL Press the Up button enough to make the safety lock disengage the safety lock bar, squeeze the lock-release handle (Fig. - Page 13 6. Once the rubber saddles have been positioned under the vehicle lifting points, operate the power switch to make contact and lift the vehicle slightly. Test to make sure the vehicle is well balanced and the contact between the rubber saddles and vehicle lifting points are secure by performing the “BUMPER TEST.”...
-
Page 14: Maintenance
7. MAINTENANCE WARNING: DISCONNECT THE POWER BEFORE SERVICING THE LIFT. IMPORTANT: THE MAINTENANCE INTERVALS INDICATED BELOW APPLY TO AVERAGE WORKSHOP USE. THE LIFT SHOULD BE INSPECTED MORE FREQUENTLY FOR SEVERE USE APPLICATIONS. 7.1 MAINTENANCE SCHEDULE It is important to keep the lift clean, dry, and well maintained by establishing a periodic preventive maintenance program to ensure trouble-free operation and long service life. -
Page 15: Every Other Year
7.1.5 EVERY OTHER YEAR Hydraulic oil should be replaced. IMPORTANT: AFTER CLEANING WORKSHOP FLOOR OR LIFT, TO MAINTAIN LIFT EFFICIENCY WE ADVISE TO LUBRICATE ROLLER BEARINGS AND SAFETY LOCK TOGGLE SHAFTS, AS PER MONTHLY MAINTENANCE INSTRUCTIONS POINT 4 (IN 7.1.2). 7.2 MAINTENANCE BY OPERATOR 1. -
Page 16: Greasing Points
7.2.2 GREASING POINTS Slide Tracks: The slide tracks should be greased every six months (or more frequently in case of noise generation). Lightly grease the slide tracks over their entire length using a brush. 7.2.3 OPERATION AND WEAR CHECKS. 1. Examine lift for structural cracks, bends, or other signs of damage prior to each use. Do not use this product if worn or damaged. -
Page 17: Troubleshooting
8. TROUBLESHOOTING PROBLEM CAUSES REMEDY The motor direction of Interchange the two phases on the main switch rotation is not correct. The oil in the hydraulic unit is Add some hydraulic oil not sufficient. The UP button is Check UP button and connection for proper operation. Replace, if needed faulty. -
Page 18: Explosive Drawing
55/56 50/51 2/3/4/5 30/30.1 24/10 2/3/4/5 47/48 11/12 7/7.1 14/15/16/17 DESCRIPTION Tow handle Hex bolt Flat washer Spring washer Hex nut Power unit pedestal Lifting Pad Flat washer Cotter Pin Hydraulic unit Locking Release handle Heavy-duty iron PU wheel Spindle 3 Spindle retainer ring Hydraulic fitting Washer... - Page 19 DESCRIPTION 90°elbow fitting Hydraulic supply hose Locking release cable Hydraulic hose Valve Straight connector Tee oil-plate Inner hex-head screw Inner hex-head screw Hex nut Safety wheel Safety lock 30.1 Tension spring Spring column pin Safety tube Safety lock bar Cylinder Spindle retainer ring Spindle 9 Spindle 5...
- Page 20 WARNING The warnings, precautions and instructions in this manual cannot cover all possible conditions and situations that may occur. The operator must understand that the operator must supply common sense and examine caution factors when using this product to determine safety in all circumstances being used. ®...
Need help?
Do you have a question about the MRL-6000 and is the answer not in the manual?
Questions and answers