Related Manuals for Leader Electronics Corp. LAG-120A
Summary of Contents for Leader Electronics Corp. LAG-120A
- Page 1 L A G - 1 2 0 A MO DE L AUDIO GENERATOR INSTRUCTION MANUAL LEADER ELECTRONICS CORP.
-
Page 3: General Description
LAG-120A AUDIO GENERATOR GENERAL DES CRIPTION Uses The LAG-120A is a wideband audio generator with sine and square output waveforms. Sine wave signals are available with a distor of less than 0.4%. Square waves with fast rise time can be used for circuit performance Synchronizing the output frequency is accomplished checks. - Page 4 FREQ. R ANGE switches: For selection of the output frequency ranges: 100Hz 1000Hz (1kHz) x100 10kHz 100kHz x10k veforms. Sine x100k 1000kHz (lMHz) rise time c a n Frequency dial: Marked in Hz: to 10; actual output frequency depends on the setting of accomplished the FREQ.
-
Page 5: Preliminary Notes
� sh01 maximum req - red. ey e. he in Sin e Fig. Rear panel functions. Cs e In m OPERATION PO ,,£ Preliminary Notes The generator output impedance is 600n, and may be directly connected to loads of 600n higher impedances. - Page 6 �:\G-120A LBO-S13A LMV-181A ©D@ 0°0 � AMPLIFIER Fig. Equipment and connections for measurements. The specified load resistance. R. is connected across the output of the amplifier, or test circuit. It should be non-inductive and have a wattage rating at least twice the expected maximum power output.
- Page 7 Frequency Response The frequency response of amplifier is determined applying a constant voltage to the amplifier input. This voltage is chosen so that the amplifier is operated below the overload point. Set the reference frequency 1kHz or 400Hz, and set ATTENUATION and VARI- ABLE for suitable amplifier output.
- Page 8 Amplifier Response avesha pe Condition RECTANGULAR SATISFACTORY FLAT LOW PRIMARY INDUCTANCE INOUTPUT TRANSFORMER: INCORRECT VALUES OF THE DEFICIE. COUPLING ELEMENTS T LOW FREQUENCIES ROUNDING HIGH LEAKAGE INDUCTANCE � OUTPUT TRANSFORMER OR HIGH DISTRIBUTED CAPACITANCE IN CIRCUIT DEFICIE T HIGH FREQUENCIES GING MALADJUSTMENT IN THE EGATIVE FEEDBACK...
-
Page 9: Maintenance
signal of exactly 1000Hz is applied, the oscillator will automatically lock in at 1000Hz. Thus, high accuracy can be achie v ed with the use of a precision frequency standard. In another application, a distorted waveform can be "purified", or filtered, by passing it through the oscillator. - Page 11 Fig. 3 - 3 Square wave adjustmen t. Frequency Adjustment: Connect a frequency counter the OUTPUT terminals. 1. Set the FREQ. RANGE switch x1k, and the dial at "I" Set the waveform switch at sine. 2. The counter reading should be 1000Hz within ±3% (or between 9 7 0 and 1030Hz). If considerably off, then set the dial so that the counter reads 1000Hz.
- Page 12 § \.;.l :?:l V> ;:;:; .., I' ", UHII I I'� 111111" 11,,,"11111 11'1'. 101, I"U" 'I� �'",� " 11/1 �. ·0 ItOl 'WIll i , II I tHII " ! IICIII '1q"f I,f! Iflill 1/[1" IIII hI' I 11'111' (11 1 1'\.
- Page 13 LEADER ELECTRONICS CORP. 2-6-33 TSUNASHIMA-HIGASHI. KOHOKU-KU, YOKOHAMA, JAPAN. TELEX: J47780 JPLEADER PHONE: (045) 541 -2121 LEADER INSTRUMENTS CORP. 3800SER AVENUE, HAUPPAUGE, N.Y. 11788 U.S.A. PHONE: (516) 231 -6900 TELEX: 510-227-9669 LEADER HAUP Printed in Japan. 85061. 5K ®...
Need help?
Do you have a question about the LAG-120A and is the answer not in the manual?
Questions and answers