Related Manuals for Systemline SN2030
Summary of Contents for Systemline SN2030
- Page 1 Instruction Manual Systemline 7 NetServer & Mini NetServer Systemline 7 NetServer & Systemline 7 Mini NetServer...
-
Page 2: Important Safety Instructions
Important safety instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. - Page 3 Instructions de sécurité importantes 1. Veuillez lire ces instructions. 2. Veuillez conserver ces instructions. 3. Veuillez prendre connaissance de tous les avertissements. 4. Veuillez suivre toutes les instructions. 5. N’utilisez pas cet appareil a proximite de l’eau. 6. Nettoyez uniquement avec un chiffon sec. 7.
-
Page 4: Table Of Contents
5.6 System Configuration 5.7 Backup 5.8 Configuration Player 5.9 Systemline Upgrade 6.0 Configuring the system 7.0 Backing up the music library 8.0 Removing or exchanging NetAmps 9.0 Systemline Upgrade Service 9.1 BLISS 9.2 Supersync 10.0 Copying existing digital music library... -
Page 5: Pack Contents
Mini Netserver (SN2010) 2.0 Introduction The Systemline 7 NetServer acts as the central portal for all S7 zones to receive stored music and internet based services via the USB connection to the S7 NetAmp. The 160GB Mini NetServer supports up to 4 zones, 320GB NetServer supports up to 8 zones, the 1TB and 2TB NetServer supports up to 24 zones. -
Page 6: Mini Netserver
Plug the Local Area Network connection into the network with an active DHCP server. Plug a USB A-B cable into each NetAmp zone. The diagram shows two zones on one NetAmp. If more than 3 zones are required, a separate USB hub can be used. Plug the power supply in and turn on. The server will boot up automatically. -
Page 7: Connections
Local Area Network (LAN) Ethernet RJ45 DC power input USB 2.0 HDMI monitor out – not used with Systemline 7 VGA monitor out – not used with Systemline 7 Microphone in – not used with Systemline 7 Audio out – not used with Systemline 7 RS232 Serial –... -
Page 8: Connecting To Netamps
4.3 Connecting to NetAmps The server requires a wired LAN connection to the network with a router and DHCP sever. Each S7 zone requires one USB connection from the server to the NetAmp. A USB hub is required if more than three zones are being used in the system as there are only three USB ports on the server itself. -
Page 9: The Netserver Web Page
This starts a new web page for the Logitech Media Server (LMS) web interface. As Systemline 7 uses an embedded LMS, this web interface becomes available and was designed as a web control for Squeezebox systems. S7 is different to standard Squeezebox systems as it uses the NetAmp for volume control and zone naming which does not appear in the LMS web page. -
Page 10: Cd Ripper
5.3 CD Ripper The CD ripper software is embedded in the server, you will need a USB optical drive plugged into a USB port of the server. It is recommended that you use a USB CD drive with a motorised drawer or eject function so that the server can eject a CD when it is finished ripping. -
Page 11: Systemline Upgrade
It is possible to delete or edit the allocated zone’s MAC address, see section 8.0. The server table of 4 active NetAmp USB connections. 5.9 Systemline Upgrade You can upload new software on the server here and also add additional software services. To upload new server software, simply press Start Upgrade. -
Page 12: Backing Up The Music Library
box. Enter the subnet mask – usually 255.255.255.0. Enter the gateway, this is the IP address of the router. The DNS settings can be left blank or you can select your own DNS servers, if you leave them blank the server will automatically find its own DNS. Once you are happy with your settings simply press submit, and the server will re-boot and after a few minutes you will need to log in with your new IP address. - Page 13 Disconnect the NetAmp to be removed from the server, browse to the server Configure Player page so that you can see all active zones, and press Refresh & submit You will see that the two connections associated with the NetAmp to be replaced have changed their state to inactive (0).
-
Page 14: Systemline Upgrade Service
You can enhance the power of the S7 NetServer by installing additional software services listed in the Systemline Upgrade page. 9.1 BLISS BLISS is a software package designed by Elsten Software Limited which will give the Systemline S7 server the following additional functions: •... -
Page 15: Supersync
PC or MAC. SuperSync can be added to the S7 NetServer by selecting it in the Systemline Upgrade page, but must also be installed on the PC or MAC hosting the iTunes library. The software gives the following useful features: •... - Page 16 Copy your digital music library into this folder. The example below has a folder structure of artist / album / file. Once complete, the Logitech Media Server will rescan this location if you have the Auto Rescan plugin enabled. See the separate document S7 Plugins available in the download section for Plugin instructions.
- Page 18 Stortford Hall Industrial Park Dunmow Road Bishops Stortford Hertfordshire CM23 5GZ United Kingdom www.armourhome.co.uk ©2015 Armour Home Electrioncs, All rights reserved. Our policy is one of continuous product improvement. We reserve the right to change the design and specifications without notice. All information is given in good faith.
Need help?
Do you have a question about the SN2030 and is the answer not in the manual?
Questions and answers