Table of Contents
Advertisement
MODEL BT26-H,
BT40-H & BT80-H
INSTALLATION,
OPERATION &
MAINTENANCE
MANUAL
Buffer Tanks
Hydronic Thermal Storage Tanks
Model BT Overview .....................................................................
Prepare the Unit .........................................................................
Location .......................................................................................
Handling/Hoisting ........................................................................
Qualified installer only -
This product must be installed only by a qualified service
technician. The installation must be done using recognized
industry practices, and in compliance with this manual and all
applicable codes. Failure to comply could result in death, serious
injury or substantial property damage.
IN UNITED STATES: 260 NORTH ELM ST. WESTFIELD, MA 01085 800-465-8558 / FAX (413) 564-5815
IN CANADA: 7555 TRANMERE DRIVE, MISSISSAUGA, ONTARIO, L5S 1L4 (905) 670-5888 / FAX (905) 670-5782
2
Overcurrent Protection & Wire Sizing .........................................
................
3
3
3
3
For information not included in this manual, see the following:
This manual includes only basic information for installation,
operation and maintenance of thermal storage tanks and
supplemental back-up heaters. For more advanced applications
and information not shown in this manual, contact Technical
Support for assistance and supplemental instructions. Call 413-
564-5530 in Westfield, MA or visit our website at www.mestek.
com to send an e-mail or review technical literature.
BT2-0218
45W30-WG0848
..................................
........................................... 5 & 6
.......................................
4
4
7
Advertisement
Table of Contents
Related Manuals for Mestek BT26-H
Summary of Contents for Mestek BT26-H
- Page 1 Support for assistance and supplemental instructions. Call 413- 564-5530 in Westfield, MA or visit our website at www.mestek. com to send an e-mail or review technical literature. IN UNITED STATES: 260 NORTH ELM ST. WESTFIELD, MA 01085 800-465-8558 / FAX (413) 564-5815...
- Page 2 Hydrogen gas is produced in a hot water system served by this heater that has not been used for a • The BT26-H and BT40-H contain a welded, 18-gauge (.047") long period of time (2 weeks or more). Hydrogen gas is extremely grade 304 stainless steel inner tank with ports for circulation, flammable.
- Page 3 Section 2: Specifications & Dimensions Figure 2 BT26-H, BT40-H and BT80-H (ALL DIMENSIONS IN INCHES) Standard Buffer Tank DIAMETER TEMPERATURE AQUASTAT PORT SENSOR 1/2 NPT WELL .250 ID DIM -A- VENT PORT 3/4 NPT DIM -B- DIM -C- 11-3/4 2-5/8 3/4 NPT DRAIN Specifications...
- Page 4 Section 4: Electrical Connection Overcurrent Protection Provide a separate power source and overcurrent protection for The figure below shows the electrical circuit for connecting the the immersion heater. Refer to the Figure 4 for detailed wiring. buffer tanks to Solstice LAHP or SCM Heat Pumps. Figure 4 Field Connections Section 5: Replacement Parts...
- Page 5 Section 6: Piping Diagrams...
- Page 6 Section 6: Piping Diagrams...
- Page 7 Section 7: Limited Warranty The “Manufacturer” warrants to the original owner at the original installation site that the Buffer Tank Product (the “Product”) will be free from defects in material or workmanship for a period not to exceed 10 years from startup. If upon examination by the Manufacturer the Product is shown to have a defect in material or workmanship during the warranty period, the Manufacturer will repair or replace, at its option, that part of the Product which is shown to be defective.
- Page 8 IN UNITED STATES: 260 NORTH ELM ST. WESTFIELD, MA 01085 800-465-8558 / FAX (413) 564-5815 IN CANADA: 7555 TRANMERE DRIVE, MISSISSAUGA, ONTARIO, L5S 1L4 (905) 670-5888 / FAX (905) 670-5782...
Need help?
Do you have a question about the BT26-H and is the answer not in the manual?
Questions and answers