1. Manuals
  2. Brands
  3. Hitachi Manuals
  4. Chainsaw
  5. CS 3630DA
  6. Handling instructions manual

Hitachi CS 3630DA Handling Instructions Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
CS 3630DA
Handling instructions

Advertisement

Table of Contents
loading

Related Manuals for Hitachi CS 3630DA

Summary of Contents for Hitachi CS 3630DA

  • Page 1 CS 3630DA Handling instructions...
  • Page 2 & ¶ ∞ §...
  • Page 3 ¶...
  • Page 4 ¡ ™ ¢ £...

  • Page 6: General Power Tool Safety Warnings

    S: Chain case: Case for covering the guide bar and saw SYMBOLS chain when the unit is not being used. T: Bolt: Bolt for fi xing the side cover in place. WARNING U: Hexagonal bar wrench: Tool for loosening and The following show symbols used for the machine.

  • Page 7: Chain Saw Safety Warnings

    f) If operating a power tool in a damp location f) Keep cutting tools sharp and clean. is unavoidable, use a residual current device Properly maintained cutting tools with sharp cutting (RCD) protected supply. edges are less likely to bind and are easier to Use of an RCD reduces the risk of electric shock.

  • Page 8: Additional Safety Warnings

    If the unit does not working properly, immediately stop 10. Follow instructions for lubricating, chain tensioning using and request repair from your Hitachi Authorized and changing accessories. Improperly tensioned or Service Center.

  • Page 9: Caution On Lithium-Ion Battery

    In such a case, charge it up immediately. ○ Always refer to your Hitachi Authorized Service Center 2. If the tool is overloaded, the motor may stop. In this for all repairs. case, release the switch of tool and eliminate causes of Attempting to repair the unit yourself may result in an overloading.

  • Page 10: Regarding Lithium-Ion Battery Transportation

    5. Do not connect directly to an electrical outlets or car cigarette lighter sockets. Power Output 6. Do not use the battery for a purpose other than those specifi ed. 7. If the battery charging fails to complete even when a specifi...

  • Page 11: Specifications

    DESCRIPTION OF NUMBERED ITEMS (Fig. 3-Fig. 47) ^ Sprocket a Switch n Brake band chamber 1 Battery Battery level indicator & Blade direction m Chain oil spout 2 Latch switch Battery level indicator * Bolt , Groove 3 Ventilation holes lamp ( Bolt hole f Hook...

  • Page 12: Optional Accessories

    OPTIONAL ACCESSORIES (sold CHARGING separately) (Page 21) Before using the power tool, charge the battery as follows. 1. Connect the charger’s power cord to the Optional accessories are subject to change without notice. receptacle. When connecting the plug of the charger to a APPLICATIONS receptacle, the charge indicator lamp will blink in red (At 1- second intervals).

  • Page 13: Installing (Replacing) Saw Chain

    (2) Regarding the temperatures and charging time of the rechargeable battery The temperatures and charging time will become as shown in Table 2. Table 2 Charger UC18YSL3 Type of battery Li-ion Temperatures at which the battery can be -10°C – 50°C recharged Charging voltage 14.4...
  • Page 14 WARNING (Check this in step 6.) After adjusting the saw chain tension, ensure the knob ○ If the chain oil supplied runs out, use Hitachi chain oil is fully tightened. sold separately or equivalent chain oil on the market. If it is loose, injury may occur.

  • Page 15: Remaining Battery Indicator

    CAUTION As the remaining battery indicator shows somewhat Be careful of the repulsive force when the brake is diff erently depending on ambient temperature and battery engaged. characteristics, read it as a reference. If you drop the unit, injury may occur. NOTE 8.

  • Page 16: Sharpening Of The Chain Blade

    (5) When cutting into wood from the bottom, touch the Precaution for cutting work upper part of the guide bar to the wood lightly. (Fig. 27) (6) As well as carefully studying the handling instructions, For large-scale operation or non-stop work ensure practical instruction in the operation of the chain To protect the motor and electronics contained in this saw prior to use, or at least practice working with the chain...

  • Page 17: About Usb Device

    When replacing the carbon brush with a new one, gage visible at the groove, and use a fl at fi le to bevel the be sure to use the Hitachi Carbon Brush Code No. portion out of the depth gage jointer. (Fig. 38) (Depth 999068.

  • Page 18: Troubleshooting

    The accessories of this machine are listed on page 21. If the battery usage time is extremely short despite repeated charging and use, consider the batteries Important notice on the batteries for the Hitachi dead and purchase new batteries. cordless power tools Please always use one of our designated genuine batteries.
  • Page 19 The charger’s vents are blocked, causing Avoid blocking the vents. its internal components to overheat. The cooling fan is not running. Contact a Hitachi Authorized Service Center for repairs. The USB power lamp The battery’s capacity has become low. Replace the battery with one that has has switched off...
  • Page 20 CS3630DA CS3630DA (NN) – – –...
  • Page 21 UC18YSL3 BSL36A18 (14.4V– 18V) 6699116 957681 944458 6698688 329897 999068 6697724...
  • Page 24 Shinagawa Intercity Tower A, 15-1, Konan 2-chome, Minato-ku, Tokyo, Japan Code No. C99724211 G Printed in China...

Table of Contents