Related Manuals for Riptide Nautilus SuperPro
Summary of Contents for Riptide Nautilus SuperPro
- Page 1 Owner’s Manual Riptide Nautilus SuperPro / Manta SuperPro 2012 Euro 240v 50 Htz Swim Spas & Exercise Pools...
-
Page 2: Table Of Contents
Checklist before filling your swim spa Maintaining swim spa water Water chemistry troubleshooting Control panel operatIons Control system features Riptide Total Alkalinity (TA) adjustment chart Main control panel operating instructions Changing your swim spa water Icon Legend Cleaning your filters... -
Page 3: Important Safety Information
3. warnInG - risk of children drowning. Although use the Riptide swim spa unless they are supervised at all your Riptide swim spa cover is not rated as a safety cover, it times. is wise to always keep the swim spa cover securely fastened 5. -
Page 4: Installation And Setup
150cm [5 feet] from all spa may not function properly. electrical outlets, switches, and other permanently Position your Riptide swim spa at least (1.5m) from all installed electrical devices. electrical outlets or devices. Indoor considerations: There are several considerations eleCtrICIan’s InstruCtIons... -
Page 5: Checklist Before Filling Your Swim Spa
250 and 500 parts per million. drain valve is fully closed. 6. Check for leaks: After the Riptide swim spa is 3. tighten equipment fittings: In the equipment full, but before turning the power on, check all the... -
Page 6: Control Panel Operations
The speed of the Variable Speed Drive jet is fully The fully programmable computer based control adjustable via the simple to operate auxiliary control system on Riptide swim spas allows total control of panel. the water temperature and jet power at the touch of a button. -
Page 7: Icon Legend
The mode button is used to switch between Standard, When your Riptide pool is first connected it will go into Economy and Sleep modes. Priming mode (after displaying some configuration Press mode to enter mode programming. Press information). -
Page 8: Variable Speed Drive
COnTrOl Panel OPeraTIOns varIaBle speed drIve lIGHt Press the light button to turn on the LED Press the variable speed drive button once lighting. Press the button once again to turn off the to turn it on or off. When turned on you can adjust lighting. -
Page 9: Auxiliary Control Panel
COnTrOl Panel OPeraTIOns auxIlIary Control panel The auxiliary control panel operates the Variable Speed Drive (VSP): ON/OFF function and jet speed. The Variable Speed Drive must first be turned on at the Main Control Panel and then turned on at the Auxiliary Control Panel. -
Page 10: Troubleshooting Guide
TrOuBlesHOOTInG GuIDe dIaGnostIC messaGes Control Panel Message Definition Action required No message on display Power has been disconnected The control panel will be disabled from the spa until power returns. The clock time may have to be reset after reconnection. All other spa settings will be preserved. - Page 11 TrOuBlesHOOTInG GuIDe dIaGnostIC messaGes Control Panel Message Definition Action required Insufficient water detected flowing Check water level in spa. Add through the heater. water if necessary. If the water is at the correct level make sure the pumps have been primed. Press any button to reset.
-
Page 12: Periodic Reminder Messages
TrOuBlesHOOTInG GuIDe dIaGnostIC messaGes Control Panel Message Definition Action required Configuration error. Spa cannot Contact your dealer. start up. A pump appears to be stuck on DISCONNECT THE SPA causing the water temperature to IMMEDIATELY. DO NOT ENTER rise, possibly to a hazardous level. THE WATER. -
Page 13: Diagnostics - Operation
TrOuBlesHOOTInG GuIDe dIaGnostICs - operatIon Once commissioned, your Riptide swim spa should operate normally when properly set up. If, however, you encounter operating problems please use this general guide. If this guide does not help you solve the problem please contact your dealer. Please also refer to dIaGnostIC messaGes on pages 10-12. -
Page 14: Water Chemistry
To correct or manage high CH, contact Note: Trichlor chlorine tablets and/or non-dichlor your authorised Riptide dealer. granular chlorines must not be used in your swim spa , they may damage the swim spa , voiding your 6. -
Page 15: Starting Your Swim Spa With New Water
3. If possible, have your authorised Riptide dealer test problem with the water and it needs to be treated the Calcium Hardness (CH) of your water and adjust or drained. -
Page 17: Changing Your Swim Spa Water
At the end of the procedure re-close the ball valve swIm spa sHell Care by reversing the instructions. Your Riptide swim spa surface is durable and easy to e). For swim spas with two volumes of water, to clean:... -
Page 18: Cover Care
Note: If your swim spa water is not emptied during See your authorised Riptide dealer for this product. periods of No-Use, you should test and chemically treat the water approximately once per week. Not... -
Page 19: Service
If you are not able to use an authorised Riptide technician, we encourage you to request and use genuine Riptide replacement parts. -
Page 20: Riptide Limited Warranty
Cabinet warranty Riptide warrants the galvanised steel sub frame not to Riptide warrants the UV Resistant Synthetic Wood crack or fracture for a period of five years from delivery cabinet material not to peel, crack, wrinkle, blister date. -
Page 21: Acts Invalidating Warranty
Riptide shall not be liable for loss of use of the Riptide swim spa, which shows the date of purchase. Notice swim spa or other incidental, consequential, special,... -
Page 22: Warranty Registration Form
Form To validate your manufacturer’s warranty please complete the form below and send to Riptide Pools Limited, 41 Robjohns Road, Chelmsford, Essex, CM1 3AG United Kingdom If possible please enclose a photocopy of the original purchase contract/receipt to negate the need for inspection on service calls.
Need help?
Do you have a question about the Nautilus SuperPro and is the answer not in the manual?
Questions and answers