Advertisement
Quick Links
WORK SAFELY! For maximum safety, perform this installation on a clean, level surface and with the
engine turned off. Place blocks or wedges in front of and behind both rear wheels to prevent
movement in either direction.
CAUTION: To avoid any possibility of bodily injury or damage to vehicle, do not attempt installation
until you are confident that the vehicle is safely secured and will not move.
NOTE: FOR PHOTOGRAPHIC PURPOSES, A 2010 MUSTANG IS SHOWN THROUGHOUT
THESE INSTRUCTIONS. 2005-2009 GT KITS INSTALL WITH IDENTICAL STEPS.
Knob
Stick Mounting
Screws (2)
Technical Support (707) 544‐4761
Installation Instructions
HURST COMPETITION AND BILLET/PLUS SHIFTER
2005-2010 Mustang w/5-speed Manual Transmission (GT only)
Knob Nut
Stick Mounting
Washers (2)
Catalog# 3910201
PARTS
Hurst Stick
Neoprene
Isolators (2)
1
Shifter (3915201 shown)
Boot Support and Zip Tie
www.HURST‐SHIFTERS.com
Advertisement
Related Manuals for HURST 3910201
Summary of Contents for HURST 3910201
- Page 1 Installation Instructions HURST COMPETITION AND BILLET/PLUS SHIFTER 2005-2010 Mustang w/5-speed Manual Transmission (GT only) Catalog# 3910201 WORK SAFELY! For maximum safety, perform this installation on a clean, level surface and with the engine turned off. Place blocks or wedges in front of and behind both rear wheels to prevent movement in either direction.
- Page 2 Slide boot up and over the shift stick and place the boot aside. Skip to STEP 5. TOOL: Plastic Trim Tool 2010: See STEP 3. Technical Support (707) 544‐4761 2 www.HURST‐SHIFTERS.com ...
- Page 3 Set boot aside. STEP 6. Carefully raise vehicle for under car access. TOOL: Floor Jack and Jack Stands Technical Support (707) 544‐4761 3 www.HURST‐SHIFTERS.com ...
- Page 4 STEP 10. Remove the two (2) hex nuts that secure the rear mount of the shifter assembly to the floor and set aside. TOOL: 10mm Deep Socket, Ratchet, Extension Technical Support (707) 544‐4761 4 www.HURST‐SHIFTERS.com...
- Page 5 (2) metal flanged sleeves from the front rubber bushings on the shifter assembly arm. TOOL: Flat Head Screwdriver Technical Support (707) 544‐4761 5 www.HURST‐SHIFTERS.com...
- Page 6 These bushings should be removed by hand to not damage them. STEP 15. Place the HURST shifter on a workbench and insert the two (2) metal flanged sleeves into the bushings in the HURST shifter assembly arm.
- Page 7 STEP 20. Tighten the hex bolt from STEP 18 that secures the shifter arm to the transmission. Insert the transmission linkage rod into the bushings at the bottom of the HURST shifter. Replace the hex nut removed in STEP 7 and tighten securely. TOOL: 10mm Wrench, 13mm Wrench NOTE: Offset (long side) of connector located on stick bottom must face towards the driver’s side.
- Page 8 STEP 21. Carefully lower vehicle. From inside the vehicle, attach the HURST upper stick to the lower stick with two (2) stick mounting washers and two (2) stick mounting screws and tighten. TOOL: 7/32 Hex Wrench (Allen Key) STEP 22. OPTIONAL: ISOLATOR INSTALLATION...
- Page 9 STEP 25. Replace the shifter boot that was removed in STEP 2. 2005-2009: Slide the boot over the HURST chrome stick. Position the boot correctly and carefully press down around the outer edges until the retainer clips snap firmly into place. Work the boot into the groove of the rubber boot support.
- Page 10 Arrange the upper center console in a way that will give you some working room between both consoles. Slide the boot over the HURST chrome stick. STEP 28. 2010 MUSTANGS ONLY: Work the boot over the rubber boot support.
- Page 11 STEP 31. Attach the Knob Nut onto the HURST stick and thread down as far as possible without forcing it. STEP 32. Screw on the HURST knob all the way down until it contacts the knob nut, then back it off until the orientation of the shift pattern/logo is correct.
- Page 12 IMPORTANT: RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE Technical Service A highly trained technical service department is maintained by Hurst Performance to answer your technical questions, provide additional product information and offer various recommendations. Technical service calls, correspondence, and warranty questions should be directed to:...
Need help?
Do you have a question about the 3910201 and is the answer not in the manual?
Questions and answers