Advertisement

Shock hazard.
Disconnect power before servicing or removing any pro-
tective covers.
Do not operate this device near water or while you are
wet.
Some medications may increase your sensitivity to ultraviolet light. It
is recommended that you consult a physician before using this sun-
bed if taking any medication or if you suspect that your skin might be
especially sensitive to sunlight.
WARNING
Wear protective eyewear.
Failure to may result in severe burns or longterm injury to the eyes.
CAUTION
Air from the room is used to cool the sunbed. Maximum ambient
room temperature should be 80°F. Place your sunbed no closer than
6" from any wall. Make sure nothing obstructs the airflow into the
sunbed's endcaps or out of the fan openings. A poorly ventilated
room may cause the unit to become hot and cause discomfort to
the user.
DANGER
DANGER
12R

Electrical Requirements

Your sunbed operates from a 120V AC source. You should have a
NEMA 5-15R electrical outlet (below) capable of providing 15 Amp
service, installed in the room in which you will use the unit. We rec-
ommend installation by a professional electrician. The outlet must be
earth grounded.

Unpacking and Inspection

Open the box and pull back the plastic sheet and, with a helper, grasp
the canopy and pull it from the carton bottom, leaving the plastic wrap
and the carton packaging. Do not try to lift the unit with the plastic still
on as it may slip.
The box should contain the canopy unit, 2 stand legs and a bag of
hardware. Inspect all items and make sure they are free from any vis-
ible damage. Report the extent of any damage to the transportation
company.

Hardware Inventory

(plus eyewear)
Caster with Brake
Quantity 4
15 AMP NEMA #5-15R
RECEPTACLE
You Will Need:
9/16" Wrench
10285B

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 12R and is the answer not in the manual?

Questions and answers

Mikey
May 4, 2025

Sunfire bed is not opening up to maximum height

1 comments:
Mr. Anderson
May 17, 2025

The Sunfire bed model 12R may not be opening up to its maximum height if the pull ring used for adjusting the height is not properly located or used. Check if the pull ring is engaged correctly to allow full canopy movement.

This answer is automatically generated

Summary of Contents for Sunfire 12R

  • Page 1 Electrical Requirements DANGER Your sunbed operates from a 120V AC source. You should have a Shock hazard. NEMA 5-15R electrical outlet (below) capable of providing 15 Amp Disconnect power before servicing or removing any pro- service, installed in the room in which you will use the unit. We rec- tective covers.
  • Page 2 Utilisé sans lunettes protectrices, ce produit peut causer des brûlures ou lé- Sunfire® Model SF71-T12-100W/P Bi-Pin sions oculaires graves. Si vous souffrez d’un malaise, arrêtez l’utilisation et consultez un Sunfire® Power Window® Model SFPW71-T12-100W/P Bi-Pin médecin. Disconnect power cord before attempting to clean, relamp, SEULES LES LAMPES SUIVANTES ONT ÉTÉ...
  • Page 3 Assembly Procedures Screw the four casters into the stand legs. Use a wrench to tighten them. Plug the three-prong 120V AC power cord into a dedicated outlet (see Electrical Requirements). Lift the canopy to use it. The unit raises and tilts to position the lamps where needed for the optimum tanning position.
  • Page 4 Operation Using Your Sunbed Before using your sunbed, please note the following: 1 Press the timer button (B). The lamps will • Your skin should be free of cosmetics, tanning oils, or other body turn on and the timer display (A) will lotions prior to tanning except for those specifically made for use show the remaining time.
  • Page 5 Allow to remain wet for 30 seconds The following lamps have been certified for use in this equipment: and then wipe the surface dry. Then disinfect as described above. SunFire® POWER WINDOW® Model SFPW71-T12-100W/P Bi-Pin SunFire® Model SF71-T12-100W/P Bi-Pin Thorough Periodic Cleaning The cooling fans draw air through the canopy and will cause a dust buildup on the lamps and reflectors.
  • Page 6 THIS PAGE INTENTIONALLY LEFT BLANK...
  • Page 7 Troubleshooting Problem Solution Canopy not tanning 1. Clean canopy, see Thorough Periodic Cleaning. 2. Replace lamps if lamp hours are greater than 800hrs. Lamps fail to light 1. Check source of AC power. Reset circuit breaker or replace fuse if necessary. 2.
  • Page 8 SUNFIRE INDUSTRIES will advise the Purchaser of the nature of the problem and the cost to yond the range of normal usage, or by accident, fire or other hazard. Repair or replacement of a the Purchaser based on the proration of the defective system or component.

Table of Contents

Save PDF