Advertisement
Quick Links
ENGLISH
1.- INTRODUCTION
SNMP06 is a powerful and versatile communication LAN card for XMART online UPS. This card
includes functions as:
- Communication for LAN Ethernet under protocols TCP/IP , UDP , SNMP , SMTP , SNTP , HTTP , HTTPS,
SSL, SSH, IPV4/IPV6, DHCP , etc.
- Connection to external XMART environmental sensor to acquire and send temperature/humidity data
to the network.
- 10M/100M autodetection speed
- Internal data logging up to 200.000 events/alarms
- Interface to monitor and control main parameters of the UPS
2.- DESCRIPTION
A:
LAN Ethernet (10/100MB)
B:
Sensor T/H
C:
Reset Jumper: To reestablish default values
1-2: Normal
2-3: Reset: Revise note 1
_______________________________________________________
SNMP-06 (161212)
SNMP06 LAN CARD
REFERENCE MANUAL
1
D:
LED green = ON: 100MB / OFF: 10MB
E:
LED yellow = ON: connection detected / OFF: connection not detected
NOTE 1: RESET: Reset function reinitializes card with factory values. It also eliminates user passwords
To apply a reset follow next procedure:
1) Remove card from UPS and set jumper between pins 2 & 3 (revise previous image)
2) Insert card into the UPS and wait during 5 minutes meanwhile reset is performed.
3) Remove card from UPS again and set jumper between pins 1 & 2.
4) Reinsert card into the UPS and wait during 5 minutes meanwhile card restarts with factory
setting.
Factory setting after reset:
IP: 192.168.102.230 (STATIC IP) ;
Subnet Mask: 255.255.255.0 ; Default gateway: 192.168.102.1
Password: 12345678
3.- INSTALATION
1: Remove cover from intelligent slot in the UPS
2: Check jumper "C" is between pins 1 & 2 in the card
3: Plug RJ45 cable in the Ethernet port of the card and connect other side to the network socket.
Check if yellow LED lights as expected.
If TH sensor is available, connect it to its related RJ11 port in the card according to next figure.
We strongly suggest to check TH sensor manual.
_______________________________________________________
SNMP-06 (161212)
SNMP06 LAN CARD
REFERENCE MANUAL
LAN
RJ45
RJ11
SENSOR TH
2
Advertisement
Summary of Contents for Xmart SNMP06
- Page 1 1.- INTRODUCTION NOTE 1: RESET: Reset function reinitializes card with factory values. It also eliminates user passwords SNMP06 is a powerful and versatile communication LAN card for XMART online UPS. This card To apply a reset follow next procedure: includes functions as: - Communication for LAN Ethernet under protocols TCP/IP , UDP , SNMP , SMTP , SNTP , HTTP , HTTPS, 1) Remove card from UPS and set jumper between pins 2 &...
- Page 2 SNMP06 card to open “Web Pro” interface in the navigator. This LAN card can storage data and events in its internal memory with any external software. SNMP06 card can also send messages and alarms by email if there is a router in the network with open access to internet.
- Page 3 SNMP06 LAN CARD SNMP06 LAN CARD REFERENCE MANUAL REFERENCE MANUAL DHCP NETWORKS STATIC IP NETWORKS To know what IP has been assigned to the card by DHCP network, user can run SNMP Manager If the network where UPS will be connected is static IP network, the network administrator must assign software to perform scan.
- Page 4 SNMP06 LAN CARD SNMP06 LAN CARD REFERENCE MANUAL REFERENCE MANUAL WEB-PRO INTERFACE UPS SETTING: Parameters Settings: In this section main UPS parameters can be revised and modified: Alarm Beep, Operation modes, etc. CONTROL: Real Time Control: Allows real time control: UPS can be turned-off and turned-on, alarm mute, battery tests, etc.
- Page 5 SNMP06 LAN CARD SNMP06 LAN CARD REFERENCE MANUAL REFERENCE MANUAL 5- EMAILS CONFIGURATION Once email section has been configured we suggest to do a TEST by selection TEST button. System will response with a message: “TEST SUCCESSFULL” when email has been sent without This card can send emails using accounts based on SNMP , SSL or TTL servers.
- Page 6 SNMP06 LAN CARD SNMP06 LAN CARD REFERENCE MANUAL REFERENCE MANUAL FIG 5: IPCONFIG -ALL To know DNS of your network, you can run from system command line of your PC, the command: ipconfig -all Your operating system will list several parameters related. Look for the line dedicated to DNS server. In the below example the value is: 192.168.1.1 (FIG.
- Page 7 SNMP06 LAN CARD SNMP06 LAN CARD REFERENCE MANUAL REFERENCE MANUAL 6- HTTPS SECURE COMMUNICATION & HTTP PORT (80) HTTP PORT (80) http https This card allows both communication protocol. 1- Select System Configuration / Web menu, FIG 7. https only Factory set is http.
- Page 8 SNMP06 LAN CARD REFERENCE MANUAL 4- Wait about 30s to save changes and try to update navigator with F5 key (in Windows). Navigator must response with a message indicating communication is lost. This is caused by port 80 is disable and HTTP communication is prohibited.