Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Gemtek Technology WLTMS-110
Summary of Contents for Gemtek Technology WLTMS-110
- Page 1 LTE CPE Quick installation Guide...
- Page 2 WLTMS-110 Connection Guide...
- Page 3 Gemtek Technology Co. Ltd. Notice Gemtek reserves the right to change specifications without prior notice.
- Page 4 Connectors 1. One RJ-45 connector for connecting to the PoE adaptor. 2. LED indicator inside and SIM card slot for inserting SIM card. 3. A grounding screw on the rear panel.
- Page 5 LED Indicators _ODU LED name Location Color LED Behavior Status Indication LED List ●●● ●●● MAIN power Blue Power On ●○○ ○○○ Power Off ○●○ Ethernet Yellow Ethernet Connected Steady ON status ○○○ Data Transmission Blinking No Ethernet action ○○● SIM status Green SIM Detected...
- Page 6 Installing LTE outdoor CPE ● Selecting a Location: LTE Outdoor CPE should be pole-mounted outdoors and aligned so its antenna faces the nearest LTE eNB. When selecting a suitable location for the unit, consider these guidelines: • Place LTE Outdoor CPE as high as possible to achieve the best possible link quality.
- Page 7 Connecting the Cables ● Outdoor Connection: Connect a grounding cable between the Ground terminal of the LTE outdoor CPE and a good ground connection. ● Preparing and connecting the cable: Use only UTP-FTP 4x2x24AWG CAT. 5E outdoor cable from an approved manufacturer.
- Page 8 2. Connect the cable • Remove the sealing cable gland plug from the gland nut. • Open the sealing gland nut and remove it. Don not disassembles the gland base from the bracket. • Insert the cable into the sealing gland base and connect it to the RJ-45 connector at the bottom of the CPE.
- Page 9 air bubbles. • Slide the cold shrink sleeve on top of the connector. Make sure that the sleeve covers both cable connector and unit connector. • Pull the cord slowly to shrink the sleeve. ● Indoor Connection 1. It is assumed that the RJ-45 is already connected to the LTE outdoor CPE.
-
Page 10: Web Interface
Web Interface Please follow the steps below to configure your device through the web interface: Open the Web browser (Internet Explorer) and enter the Step1: default IP address of the ODU CPE, which is : http://192.168.15.1 Web browser Enter ODU administrator login username/password to access Step2: the web management interface. - Page 11 Web management interface The page shown here gets displayed in your browser after Step3: login; you can now configure the device settings. GUI Interface Mode: Operator: APN Name (More bar means better Signal: signal) (Disconnect, no signal)
- Page 12 Europe – EU Declaration of Conformity This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following test methods have been applied in order to prove presumption of conformity with the essential requirements of the R&TTE Directive 1999/5/EC: EN 301 908-1 V7.1.1 EN 301 908-13 V6.2.1 EN 62311:2008...
- Page 13 [German] Übereinstimmung mit den grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet. Eesti [Estonian] Käesolevaga kinnitab [tootja nimi = name of manufacturer] seadme [seadme tüüp = type of equipment] vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele. English Hereby, [name of manufacturer], declares that this [type of equipment] is in compliance with the essential requirements and other relevant provisions of...
- Page 14 1999/5/EC. Magyar Alulírott, [gyártó neve] nyilatkozom, hogy a [... típus] megfelel a vonatkozó alapvetõ [Hungarian] követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak. Niniejszym [nazwa producenta] oś iad za, że [nazwa wyrobu] jest zgodny z Polski [Polish] zasad i zy i y oga i oraz pozostały i stoso y i posta o ie ia i Dyrekty y 1999/5/EC.
- Page 15 Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Need help?
Do you have a question about the WLTMS-110 and is the answer not in the manual?
Questions and answers