AMH UltraMig 175 Instruction Manual
  1. Manuals
  2. Brands
  3. AMH Manuals
  4. Welding System
  5. UltraMig 175
  6. Instruction manual

AMH UltraMig 175 Instruction Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

U
l
t
r
U
l
t
r
I
N
S
I
N
S
a
M
i
a
M
i
T
R
U
C
T
I
O
T
R
U
C
T
I
O
- 1 -
UltraMig 175
g
1
7
g
1
7
N
M
A
N
U
A
N
M
A
N
U
A
5
5
L
L

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the UltraMig 175 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for AMH UltraMig 175

Summary of Contents for AMH UltraMig 175

  • Page 1 UltraMig 175 - 1 -...

  • Page 2: Table Of Contents

    UltraMig 175 Table of contents AFETY NSTRUCTIONS ..........................4 1. Safety in the use of a power source for electric arc welding ..............4 2. Work station ............................... 4 3. Servicing ..............................4 4. Wire feed devices ............................4 5. Maintenance ............................... 4 6.
  • Page 3 UltraMig 175 AINTENANCE ............................... 14 1. Maintenance ............................. 14 2. Installation..............................14 3. Troubleshooting ............................14 175)......................16 XPLODED VIEWS LTRA MB14) ......................19 XPLODED VIEW ORCH ECHNICAL INFORMATIONS ........................21 ARRANTY ..............................22 - 3 -...

  • Page 4: Safety Instructions

    UltraMig 175 Safety Instructions 1. Safety in the use of a power source 3. Servicing for electric arc welding Before beginning any inspection or repair of the inside of the machine it is necessary to make certain that the The equipment which you have just acquired will give...

  • Page 5: Personal Protection

    UltraMig 175 6. Personal protection • The hair and face against spatter and sparks. The operator must be dressed and protected in a The welding mask, whether or not it forms part of the manner appropriate for the work being performed.

  • Page 6: Safety Against Smoke, Vapors, And Noxious, Toxic Gases

    UltraMig 175 8. Safety against smoke, vapors, and noxious, toxic gases Arc welding work must be carried out only in suitably ventilated areas. The fumes emitted during welding in workshops should be exhausted progressively as they are produced, as closely as possible to their point of emission, and as efficiently as possible.

  • Page 7: General Informations

    UltraMig 175 General informations 1. Description of installation 3. Installation equipment The UltraMig 175 is a SYNERGIC AND MANUAL MIG 3.1 Wire feed unit welding unit which uses a thyristor-based power source controlled by a microprocessor with remote The drive unit comes fitted with one set of rollers which opération.

  • Page 8: Operating Instructions

    UltraMig 175 3.4 Gas connections 4. Operating instructions A. Open the cylinder valve slightly to remove any A. Connect the unit to a 220 Volt 15 amp outlet. impurities and close it immediately. B. Turn the main switch on the control panel to the on B.

  • Page 9: Function And Setting

    UltraMig 175 Function and setting 1. Operating in synergic mode 3. Thermal safety During semi-automatic MIG welding, "operating in The YELLOW indicator on the front control panel will synergic mode" means that with a single control knob light up if the transformer overheats. Once it has...

  • Page 10: Wire Reel

    UltraMig 175 3. Finish the setup with the outer cone, then the lock 6. Wire reel washer, and the wingnut until the reel is lightly clamped. Installing the reel : 4. Run the machine with the wire feed speed set to The unit is shipped with a reel cone set to be mounted maximum (adjust on torch).

  • Page 11: Operating And Welding Instructions

    UltraMig 175 Operating and welding instructions 1. How to hold the welding torch C. THE TORCH SHOULD NOT BE MOVED AWAY When approaching the working piece with the welding FROM THE SURFACE ONCE WELDING HAS torch, it is important to use the following technique: BEGUN.

  • Page 12: Welding Steel

    UltraMig 175 2. Welding steel E. When welding on a slope (fig. 3), the penetration of A. Use a gas mixture of 25% CO2 and 75% ARGON the weld will decrease as the slope increases. The with a 10 to 16 l/min flow.

  • Page 13: Aluminium Welding

    UltraMig 175 G. When a spot nozzle is not available, use a standard 3. Aluminium welding conical welding nozzle and maintain a distance of 6mm to 12mm between the nozzle and the sheet A. Aluminum welding with a standard torch normally metal.

  • Page 14: Maintenance

    UltraMig 175 Maintenance Blow dry compressed air through the cable liner after each wire spool change. Carry out this procedure from the motor side of the torch cable. 1. Maintenance Contact tips are designed for prolonged use. They are nevertheless worn by the passage of the wire and the...
  • Page 15 UltraMig 175 Situation Action Wire does not feed Check the fuse. Check voltage. If voltage OK, replace the motor reducing gear set. No gas Check the condition of the cylinder. Check the condition of the pressure regulator and the hose.

  • Page 16: Exploded Views (Ultramig 175)

    UltraMig 175 Exploded views (UltraMig 175) - 16 -...
  • Page 17 UltraMig 175 - 17 -...
  • Page 18 UltraMig 175 No. AMH DESCRIPTION 51.600.02.53 OCKER SWITCH 09.125.01.15 ONTROL KNOB 27.800.01.35 IRCUIT BOARD 17.100.00.50 AIN SWITCH 07.123.00.21 TRANSFORMER 07.123.00.26 TRANSFORMER 17.800.01.30 LEEDER RESISTOR 17.800.02.10 AS VALVE 10.800.10.65 AS HOLE 01.138.01.11 CABLE 17.115.00.05 07.800.05.14 HOKE 31.162.00.30 APACITOR BRACKET 10.135.00.33 EAT SINK 10.135.00.34...

  • Page 19: Exploded View (Torch Mb14)

    UltraMig 175 Exploded view (Torch MB14) - 19 -...
  • Page 20 UltraMig 175 No. AMH DESCRIPTION 02.205.01.77 ONG BOLT 02.205.01.78 HORT BOLT 03.203.02.03 PPER PART HANDLE 02.205.01.10 PACER BUSHING 03.203.01.05 ORCH CABLE 03.203.01.06 ORCH CABLE 02.205.01.45 ABLE SUPPORT 02.205.01.75 OCK NUT 02.205.01.55 ORCH BODY SEAT 02.205.01.40 ORCH BODY 02.205.01.86 WAN NECK 02.205.01.20...

  • Page 21: Technical Informations

    UltraMig 175 Technical informations Primary Input voltage 200-240 V Frequency 60 Hz Secondary Voltage output (max.) (115V) 24 V 14.0 – 20.0 V Voltage range Current range 20 – 175 A Current 30% (Duty cycle) 130 A Functions Control Micro-processor...

  • Page 22: Warranty

    Fax : 1-418-722-6108 AMH Canada LTD. If a product warranty card has not been completed or proof of purchase is not available, the warranty will be deemed to become effective at the time the product leaves the factory or authorized AMH warehouse.

Table of Contents