Related Manuals for MachineryHouse BS-461AS
Summary of Contents for MachineryHouse BS-461AS
-
Page 1: Instruction Manual
Page 1 Instruction Manual for BS-461AS (B035A) 03/12/2014 INSTRUCTION MANUAL BS-461AS Dual Mitre, Swivel Head Metal Cutting Band Saw (415V) 600 x 440mm (W x H) Rectangle B035A... - Page 2 Page 2 Instruction Manual for BS-461AS (B035A) 03/12/2014...
-
Page 3: Table Of Contents
Page 3 Instruction Manual for BS-461AS (B035A) 03/12/2014 TABLE OF CONTENTS ACCIDENT PREVENTION AND SAFETY REGULATION ..............1 1.1 Advice for the operator ......................... 1 1.2 The electrical equipment according to European Standard" CENELEC EN 60204-1" ......1 1.3 Warning labels ............................. 1 1.4 Emergencies according to European Standard “CENELEC EN 60204-1”... -
Page 4: Accident Prevention And Safety Regulation
Page 4 Instruction Manual for BS-461AS (B035A) 03/12/2014 - In the event of a power cut, the specific start-up ACCIDENT PREVENTION AND button must be reset. SAFETY REGULATION - The machine has been tested in conformity with This machine has been designed to comply with... -
Page 5: Machine Transportation And Installation
Page 5 Instruction Manual for BS-461AS (B035A) 03/12/2014 MACHINE TRANSPORTATION AND Minimum requirements for housing the machine INSTALLATION - Main voltage and frequency must comply with the machine’s motor requirements. - Environment temperature should fall within Machine dimensions (-10ºC to + 50 ºC). -
Page 6: Install The Outlet Tray, Length Stop Device And Mobile Coolant Trays
Page 6 Instruction Manual for BS-461AS (B035A) 03/12/2014 Remove mobile cover by lift handle up and pull it Install the outlet tray, length stop device out from the base as showing direction. and mobile coolant trays. Install the outlet tray and stop bar on to the... -
Page 7: Deactivation Of Machine
Page 7 Instruction Manual for BS-461AS (B035A) 03/12/2014 C. Emergency Stop Button – Press to stop all Deactivation of machine If the machine is to be out of use for a long period, machine functions. it is advisable to proceed as follows: D. -
Page 8: Chip Tray
Page 8 Instruction Manual for BS-461AS (B035A) 03/12/2014 Chip tray Open Blade Cover Safety Device Removable chip tray for capture of chips and debris. When blade cover is open, close the blade cover as instructed below: 1. Use one hand on the cover handle to hold Blade broken micro switch the blade cover. -
Page 9: 3.11 Attached Coolant Device
Page 9 Instruction Manual for BS-461AS (B035A) 03/12/2014 1. Disconnect machine from the power source. 3.11 Attached coolant device 2. Loosen two hex socket cap screws (X) 3. Move guide seat (Y) up or down until a clearance of .003" to .005" between back of blade and thrust roller is obtained. -
Page 10: Blade Tracking Adjustment (Hydraulic Blade Tension Type) (Optional)
Page 10 Instruction Manual for BS-461AS (B035A) 03/12/2014 - Connect machine to the power source. Blade tracking has been set at the factory and has Placing the saw blade onto the drive no adjustment required. If a tracking problem wheel and flywheel... -
Page 11: Operation Preparations
Page 11 Instruction Manual for BS-461AS (B035A) 03/12/2014 OPERATION PREPARATIONS Angle cutting The machine can cut angles up to 60 in both directions Setting the saw blade height Lock lever Angle scale Start the hydraulic power and Arise saw bow to the properly height. -
Page 12: Changing The Transmission Belt
Page 12 Instruction Manual for BS-461AS (B035A) 03/12/2014 speed, it needs to measure with blade speed - Release blade tension by turning the blade meter. tensioning handle counter-clockwise until blade is free. - Remove the old blade from both wheels and out of each blade guide. -
Page 13: Laser Guide Device (Optional)
Page 13 Instruction Manual for BS-461AS (B035A) 03/12/2014 - Turn the power off and recheck the blade tension and chip brush. If further adjustment is necessary disconnect the saw from the power source, make adjustments, and re-connect the power. Wing nut... -
Page 14: Operation Cycle
Page 14 Instruction Manual for BS-461AS (B035A) 03/12/2014 - Open the vise more than 250mm. - Secure the material, use the vise close button - Attach and Tighten posts bolts’ (A) on to vises. (I). Then attach the vertical press to the top of the - Base on the diameter of the material;... -
Page 15: Monthly Maintenance
Page 15 Instruction Manual for BS-461AS (B035A) 03/12/2014 - Use compressed air to clean the blade guides - To change the gear box oil (guide bearings and drain hole of the lubricating - Lower the saw bow to horizontal position. -
Page 16: Noise Tests
Page 16 Instruction Manual for BS-461AS (B035A) 03/12/2014 NOISE TESTS The test was held under environmental noise levels of 65db. Noise measurements with the machine operating unload was 71db. Noise level during the cutting of mild carbon steel was 73db. - Page 17 Page 17 Instruction Manual for BS-461AS (B035A) 03/12/2014...
- Page 18 Page 18 Instruction Manual for BS-461AS (B035A) 03/12/2014 SECTION A – PARTS LIST...
- Page 19 Page 19 Instruction Manual for BS-461AS (B035A) 03/12/2014 SECTION A – PARTS LIST...
- Page 20 Page 20 Instruction Manual for BS-461AS (B035A) 03/12/2014...
- Page 21 Page 21 Instruction Manual for BS-461AS (B035A) 03/12/2014 SECTION B – PARTS LIST...
- Page 22 Page 22 Instruction Manual for BS-461AS (B035A) 03/12/2014 SECTION B – PARTS LIST...
- Page 23 Page 23 Instruction Manual for BS-461AS (B035A) 03/12/2014...
- Page 24 Page 24 Instruction Manual for BS-461AS (B035A) 03/12/2014 SECTION C – PARTS LIST...
- Page 25 Page 25 Instruction Manual for BS-461AS (B035A) 03/12/2014 SECTION C – PARTS LIST...
- Page 26 Page 26 Instruction Manual for BS-461AS (B035A) 03/12/2014...
- Page 27 Page 27 Instruction Manual for BS-461AS (B035A) 03/12/2014 SECTION D – PARTS LIST...
- Page 28 Page 28 Instruction Manual for BS-461AS (B035A) 03/12/2014...
- Page 29 Page 29 Instruction Manual for BS-461AS (B035A) 03/12/2014 SECTION E – PARTS LIST...
- Page 30 Page 30 Instruction Manual for BS-461AS (B035A) 03/12/2014...
- Page 31 Page 31 Instruction Manual for BS-461AS (B035A) 03/12/2014 SECTION F – PARTS LIST...
- Page 32 Page 32 Instruction Manual for BS-461AS (B035A) 03/12/2014...
- Page 33 Page 33 Instruction Manual for BS-461AS (B035A) 03/12/2014 General Machinery Safety Instructions Machinery House requires you to read this entire Manual before using this machine. 1. Read the entire Manual before starting 14. Use correct amperage extension cords. machinery. Machinery may cause serious injury if Undersized extension cords overheat and lose not correctly used.
- Page 34 Page 34 Instruction Manual for BS-461AS (B035A) 03/12/2014 Metal Cutting Bandsaw Safety Instructions Machinery House requires you to read this entire Manual before using this machine. 1. Maintenance. 8. Understand the machines controls. Make sure the bandsaw is turned Make sure you off and disconnect from the main power supply understand the use and operation of all controls.
- Page 35 Page 35 Instruction Manual for BS-461AS (B035A) 03/12/2014...