Subscribe to Our Youtube Channel
Related Manuals for AV-GAD Eye-Spy II
Summary of Contents for AV-GAD Eye-Spy II
-
Page 1: Installation Instructions
Installation Instructions Version IV (Built-In EOL mode removed) Eye-Spy II – Standard (w/o bracket) Eye-Spy II PRO – With bracket Eye-Spy II Quad Pet – With bracket Eye-Spy II Curtain – (w/o bracket) -
Page 2: Preliminary Considerations
Preliminary Considerations Choose the mounting location after careful consideration of the protected area. Locate the Eye-Spy II in a way that the intruder will cross the infrared beam pattern. Do not mount the unit in direct sunlight, windy place, near airflow, high voltage lines or close to heat sources. - Page 3 Mounting Procedure Mount the Eye-Spy II on a flat wall or corner. Usually corner installation provides optimal coverage. The Eye-Spy II special optics provides optimal covering and range when mounted at 1.60 – 3.30 meter (5 to 12 ft) height. PCB vertical adjustment not required.
- Page 4 Punch out the wires entry rectangular knockout in the Eye-Spy II base, as shown in figure 1. Insert the cable and attach the base to the wall or corner. To prevent false alarm caused by insects and air stream, seal the cable entry knockout and holes that are not in use.
- Page 5 Install the bracket to wall (after inserting the cable), first remove the Pan Screw from the bracket and tighten this screw from the detector base side. Attach the Eye-Spy II base to the swivel bracket with the two supplied locking screws (figure 1, 3).
- Page 6 Terminal Connections Wire the cable to the terminal block at the PIR board as shown in figure 4. Wire the Tamper switch to a separate zone, programmed at alarm panel as tamper or 24H type. 12V DC: Power supply inputs ALARM: N.C.
- Page 7 Printed Circuit Board Adjustments (PCB) Before closing the front cover make sure to tighten the PC Board holding screw. QUAD PET TYPE: Typical mounting height: 2.2 meter (7 ft). Select the required PET mode; 18 (40 lb) or 30 kg (66 lb), refer to figure 3. It’s recommended to install the PIR with the bracket in 5 degrees vertical slop.
- Page 8 Factory default is no pulse count. EOL MODE (Jumper Settings): Starting Sep. 2006 the EOL option removed. PET MODE (Eye-Spy II Quad PET only): Quad Pet is recommended for harsh indoor areas and sites with Pets. Pet jump towards the PIR may cause alarm.
- Page 9 3 setting (factory default is mid range). When adjustment is complete, tighten the PIR cover screw. For Eye-Spy II with swivel bracket, refer to figure 3; tighten the two adjustment screws. WARNING: Test this alarm product at least once a week.
- Page 10 not manufactured by Seller, Seller can not guarantee the performance of the security system which uses this product. Seller’s obligation and liability under this warranty is expressly limited to repairing or replacing, at Seller’s option, within a reasonable time after the date of delivery, any product not meeting the specifications.
- Page 11 No employee or representative of Seller is authorized to change this warranty in any way or grant any other warranty. WARNING: This product should be tested at least once a week. ====================================== Standards The EYS II Conforms to European Union (EU) Electro Magnetic Compatibility (EMC) Directive number 89/336/EEC (amended by 92/31/EEC &...
- Page 12 Operating Temperature: -10 to +50 o C (+14 to +122 Temperature Compensation: Automatically Storage Temp. : -20 to +60 o C (-4 to +140 Eye-Spy II is a registered trademark of Av-Gad Systems Ltd. Av-Gad systems Ltd., EYE-SPY II, VER 4, 11/2008 http//www.av-gad.com...
Need help?
Do you have a question about the Eye-Spy II and is the answer not in the manual?
Questions and answers