Operation - Stanley HV18 User Manual

Pre-opperation Procedures
Operating Instructions
Check oil in reservoir. The end of the dipstick is
the low level and the high level is at the line on
the dipstick. If necessary fill the reservoir with
ISO Grade 32 hydraulic oil.
Pre-opperation Procedures
PRE-OPERATION PROCEDURES
Check oil in reservoir. The end of the dipstick is
1. Check oil in the reservoir. The end of the dipstick
the low level and the high level is at the line on
is the low level and the high level is at the line on
the dipstick. If necessary fill the reservoir with
the dipstick. If necessary fill the reservoir with ISO
ISO Grade 32 hydraulic oil.
Grade 32 hydraulic oil.
DIPSTICK
Connect the pressure hose from the supply circuit
to the IN port on the manifold and the return hose
to the OUT port.
The recommended hose size for the supply hoses
DIPSTICK
is 3/4 in. I.D. with 3000 psi working pressure.
Figure 2. Check Oil Level
Connect the pressure hose from the supply circuit
2. Connect the pressure hose from the supply circuit
to the IN port on the manifold and the return hose
to the IN port on the manifold and the return hose to
to the OUT port.
the OUT port.
3. The recommended hose size for the supply hoses is
The recommended hose size for the supply hoses
3/4 in. ID with 3000 psi working pressure.
is 3/4 in. I.D. with 3000 psi working pressure.
SUPPLY CIRCUIT
SUPPLY CIRCUIT
8
8
10 ► HV18 User Manual

OPERATION

OK
OK
HIGH LEVEL LINE
HIGH LEVEL LINE
Model #
IN
S/N
OUT
Model #
IN
S/N
OUT
TOOL CIRCUIT
Figure 3. Tool Circuit
TOOL CIRCUIT
WARNING
Supply circuit relief setting must not exceed 3000 psi/207
bar. Higher pressures may cause personal injury and
damage to the equipment.
The rated working pressure of supply circuit hydraulic
hoses must be equal or higher than the relief setting on the
hydraulic system.
WARNING
Supply circuit relief setting must not exceed 3000 psi/207
Operation bar. Higher pressures may cause personal injury and
damage to the equipment.
Supply circuit relief setting must not exceed 3000
The rated working pressure of supply circuit hydraulic
Turn the tool circuit control valve off by pulling hoses must be equal or higher than the relief setting on the
psi/207 bar. Higher pressures may cause personal
hydraulic system.
injury and damage to the equipment.
the knob and turning until the detent pin is locked
into the shallow groove.
The rated working pressure of supply circuit hydraulic
hoses must be equal or higher than the relief setting
Operation
on the hydraulic system.
Connect tool hoses to the couplers in the
"PRESS" and "RETURN" ports. The
OPERATION
recommended hose length is 25 ft. / 8 m with a
Turn the tool circuit control valve off by pulling
1/2 in. / 12.7 mm inside diameter. The hoses must
the knob and turning until the detent pin is locked
1. Turn the tool circuit control valve off by pulling the
have a working pressure rating of at least
into the shallow groove.
knob and turning until the detent pin is locked into
2500 psi/175 bar. Also see "HYDRAULIC HOSE
the shallow groove.
REQUIREMENTS" earlier in this manual.
Connect tool hoses to the couplers in the
2. Connect tool hoses to the couplers in the PRESS
"PRESS" and "RETURN" ports. The
and RETURN ports. The recommended hose length
Turn supply circuit on then turn tool circuit
recommended hose length is 25 ft. / 8 m with a
is 25 ft./8 m with a 1/2 in./12.7 mm inside diameter.
control valve on to enable tool circuit.
The hoses must have a working pressure rating of
1/2 in. / 12.7 mm inside diameter. The hoses must
at least 2500 psi/175 bar. Also see HYDRAULIC
have a working pressure rating of at least
HOSE REQUIREMENTS earlier in this manual.
2500 psi/175 bar. Also see "HYDRAULIC HOSE
3. Turn supply circuit on then turn tool circuit control
REQUIREMENTS" earlier in this manual.
valve on to enable tool circuit.
Turn supply circuit on then turn tool circuit
control valve on to enable tool circuit.
RETURN
TOOL
ON/OFF
PRESS
RETURN
TOOL CIRCUIT
TOOL
CONTROL VALVE
ON/OFF
PRESS
TOOL CIRCUIT
CONTROL VALVE
RELIEF VALVE
RELIEF VALVE