Carrier 070-08/024070 Installation, Start-Up, Operating And Service And Maintenance Instructions page 37

TERMINALS WITH
THERMOSTAT REMOVED
(ANITICIPATOR, CLOCK, ETC.,
MUST BE OUT OF CIRCUIT.)
FROM UNIT 24-V
CONTROL TERMINALS
EXAMPLE: 5.0 AMPS ON AMMETER = 0.5 AMPS FOR THERMOSTAT
10 TURNS AROUND JAWS ANTICIPATOR SETTING
A96316
Fig. 54--Amp Draw Check With Ammeter
c. Unblock return air to permit normal circulation.
d. Burners will re-light when lurnace cools down.
2. Check draft salk:guard switch.
The purpose of this control is to cause the sale shutdown of the
l?lrnace during certain blocked vent conditions.
a. Verify vent pipe is cool to the touch.
b. Disconnect power to furnace and remove vent connector
l?'om lilrnace vent elbow.
c. Restore power to lurnace and set room thermostat above
room temperature.
d. After normal start-up, allow furnace to operate liar 2
minutes, then block vent elbow in furnace 80 percent of
vent area with a piece of fiat sheet metah
e. Furnace should cycle olT within 2 minutes. If gas does not
shut off within 2 minutes, determine reason draft salcgnard
switch did not function properly and correct condition.
f. Remove blockage 15"orelurnace vent elbow.
g. Switch will auto-reset when it cools.
h. Re-install vent connector.
NOTE: Should switch remain open longer than 3 minutes,
furnace control board will lockout the furnace liar 3 hours. To reset
furnace control board, turn thermostat below room temperature or
from HEAT to OFF and turn 115v power OFF, then back ON.
3. Check Pressure Switch
This control proves operation of the draft inducer blower.
a. Turn o11 l lS-v power to lurnace.
b. Disconnect inducer motor lead wires from wire harness.
c. Turn on 115-v power to li_rnace.
d. Set thermostat to "call Ik_rheal" and wait 1 minute. When
pressure switch is functioning properly, hot surface igniter
should NOT glow and control diagnostic light flashes a
status code 32. If hot surface igniter glows when inducer
motor is disconnected, shut down l_lrnace immediately.
e. Determine reason pressure switch did not lunction properly
and correct condition.
f. Turn off 115-v power to furnace.
g. Reconnect inducer motor wires, replace outer door, and
turn on 115-v power.
37
Table 10-GAS RATE (CU FT/HR)
SECONDS SIZE OF TEST DiAL SECONDS SIZE OF TEST DiAL
FOR 1 1 2 5 FOR 1 1 2 5
REVOLUTION Cu Ft Cu Ft Cu Ft REVOLUTION iCu Ft Cu Ft Cu Ft
10 360 720 1800 50 72 144 360
11 327 655 1638 51 71 141 355
12 300 600 1500 52 68 138 348
18 277 555 1385 53 68 136 340
14 257 514 1286 54 67 133 333
15 240 480 1200 55 65 131 327
16 225 450 1125 56 64 129 321
17 212 424 1059 57 63 126 316
18 200 400 1000 58 82 124 310
19 189 379 947 59 81 122 305
20 180 360 900 60 80 120 300
21 171 343 857 62 58 118 290
22 184 327 818 64 56 112 281
23 157 313 783 68 54 109 273
24 150 300 750 68 53 108 265
25 144 288 720 70 51 103 257
26 138 277 892 72 50 100 250
27 133 267 867 74 48 97 243
28 129 257 843 78 47 95 237
29 124 248 821 78 46 92 231
30 120 240 8OO 80 45 90 225
31 116 232 581 82 44 88 220
32 113 225 563 84 43 88 214
33 109 218 545 88 42 84 209
34 106 212 529 88 41 82 205
35 103 208 514 90 40 80 200
38 100 200 500 92 39 78 196
37 97 195 488 94 38 78 192
38 95 189 474 98 38 75 188
39 92 185 462 98 37 74 184
40 90 180 450 100 36 72 180
41 88 178 439 102 35 71 178
42 86 172 429 104 35 89 173
48 84 167 419 106 34 88 170
44 82 164 409 108 33 87 187
45 80 160 400 110 33 85 184
46 78 157 391 112 32 84 181
47 76 153 383 116 31 82 155
48 75 150 375 120 30 80 150
49 73 147 367
h. Blower will run lot 90 sec belol'C beginning the call R_r
heat again.
i. Furnace should ignite normally.
Step 5--Checklist
1. Put away tools and instruments. Clean up debris.
2. Verify that blower OFF-DELAY time is selected as desired.
3. Verify that blower and burner access doors are properly
installed.
4. Cycle test lurnace with room thermostat.
5. Check operation of accessories per manufacturer's instruc-
tions.
6. Review User's Guide with owner.
7. Attach literature packet to l_lrnace.