Gigabit 1000base-sx/lx pci 64-/32-bit fiber nics fully complies with all ieee 802.3z and 1000base-sx/lx standards to provide a reliable gigabit ethernet connection (18 pages)
Black box hpiiisi twinax card user manual (130 pages)
Summary of Contents for Black Box LCL931A
Page 1
Order toll-free in the U.S. 24 hours, 7 A.M. Monday to midnight Friday: 877-877-BBOX SUPPORT FREE technical support, 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746 INFORMATION Mail order: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018 Web site: http://www.blackbox.com · E-mail: info@blackbox.com...
Page 2
CITYLIGHT FIBRE CHANNEL CARD FEDERAL COMMUNICATIONS COMMISSION CANADIAN DEPARTMENT OF COMMUNICATIONS RADIO FREQUENCY INTERFERENCE STATEMENTS This equipment generates, uses, and can radiate radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer’s instructions, may cause interference to radio communication. It has been tested and found to comply with the limits for a Class A computing device in accordance with the specifications in Subpart J of Part 15 of FCC rules, which are designed to provide reasonable protection against such interference...
Page 3
CITYLIGHT FIBRE CHANNEL CARD NORMAS OFICIALES MEXICANAS (NOM) ELECTRICAL SAFETY STATEMENT INSTRUCCIONES DE SEGURIDAD 1. Todas las instrucciones de seguridad y operación deberán ser leídas antes de que el aparato eléctrico sea operado. 2. Las instrucciones de seguridad y operación deberán ser guardadas para referencia futura.
Page 4
CITYLIGHT FIBRE CHANNEL CARD 11. El aparato eléctrico deberá ser connectado a una fuente de poder sólo del tipo descrito en el instructivo de operación, o como se indique en el aparato. 12. Precaución debe ser tomada de tal manera que la tierra fisica y la polarización del equipo no sea eliminada.
Page 5
CITYLIGHT FIBRE CHANNEL CARD CERTIFICATION NOTICE FOR EQUIPMENT USED IN CANADA The Canadian Department of Communications label identifies certified equipment. This certification means that the equipment meets certain telecommunications-network protective, operation, and safety requirements. The Department does not guarantee the equipment will operate to the user’s satisfaction.
CITYLIGHT FIBRE CHANNEL CARD 1. SPECIFICATIONS Specifications for LCL931/934A Fibre Channel Card DATA RATE 1062 MBPS SINGLE-MODE FIBER LINK SHORT HAUL LONG HAUL TYPICAL POWER BUDGET 19dB 21dB MIN POWER BUDGET 18dB 20dB TYPICAL LAUNCH POWER -1dBm +1dBm MINIMUM LAUNCH POWER -2dBm 0dBm RECEIVE SENSITIVITY...
Page 8
CITYLIGHT FIBRE CHANNEL CARD RECEIVE SATURATION 0dBm -3dBm LINK LENGTH (TYPICAL) UP TO 5KM SINGLE-MODE 9/125µm 275M (MIN) 550M (REQUIRES OFFSET MULTIMODE 62.5/125µm LAUNCH FIBER) 500M (MIN) 550M (REQUIRES OFFSET MULTIMODE 50/125µm LAUNCH FIBER) CONNECTORS USER PORT SINGLE-MODE LINK SC/FC (ORDER TIME OPTIONS) ENVIRONMENTAL TEMPERATURE...
Page 9
CITYLIGHT FIBRE CHANNEL CARD CE 89/336/EEC FCC PT 15 LIMIT B CARD VARIANTS LCL931A FIBRE CHANNEL, MM SC TO SM SC, 15 KM LCL932A FIBRE CHANNEL, SM SC TO SM SC, 15 KM LCL933A FIBRE CHANNEL, MM SC TO SM SC, 40 KM...
CITYLIGHT FIBRE CHANNEL CARD 2. PRODUCT OVERVIEW The CityLIGHT Fibre Channel Card is part of the CityLIGHT system and is designed to provide a basic transport service for Fibre Channel attached devices. It converts multimode 850nm or single-mode 1300nm fiber signals for transmission on single-mode fiber between connected devices over distances up to 15km on single-mode fiber using short haul optics or 40km using long haul optics.
CITYLIGHT FIBRE CHANNEL CARD Note the short haul optics are limited in distance by the spectral width of the laser and not the power budget available on the link. See Specifications Section for more details of drive distance. 2.3 External Attenuator All high-power or long haul CityLIGHT cards have been designed for long distance transmission and provide a minimum optical budget ranging between 20dB and 25dB.
CITYLIGHT FIBRE CHANNEL CARD 2.5 Ergonomics The CityLIGHT Fibre Channel Card is able to be installed in any of the CityLIGHT chassis types. 2.6 Power Supply The CityLIGHT Fibre Channel Card receives all its power requirements from the PSUs mounted in the CityLIGHT chassis. Consult your chassis manual for details.
Page 14
CITYLIGHT FIBRE CHANNEL CARD Fiber Port Link Status This gives an indication of the state of the fiber connections to the CityLIGHT Fibre Channel Card. The single-mode fiber port states can be: Inserted (both ends are inserted and can carry data - single- mode receive port is correctly connected).
CITYLIGHT FIBRE CHANNEL CARD Rail Voltage The voltage actually present at the card. In non-redundant PSU chassis this can be used to monitor the state of the power supply and should always be greater than 4.9V. This field gives an indication of the operating state of the PSUs in the CityLIGHT chassis associated with the transceiver displayed, i.e.
CITYLIGHT FIBRE CHANNEL CARD 3. INSTALLATION NOTE: The CityLIGHT Gigabit Ethernet Card is hot-swappable; the power to the CityLIGHT 1U or 3U Chassis and the CityLIGHT 2-Card Chassis does not need to be turned off during installation. 3.1 Tools Required To install the CityLIGHT Fibre Channel Card, the following tools are required: Flat-Bladed Screwdriver Rack/Suitable Bench Space...
Page 17
CITYLIGHT FIBRE CHANNEL CARD Push the CityLIGHT Fibre Channel Card along the card guides into the slot until it engages with the connector inside the CityLIGHT chassis. Tighten the two captive screws on the front panel of both CityLIGHT Fibre Channel Cards to secure them in position. Make sure the Rx Alarm LED and Link LED on the front panel of both CityLIGHT Fibre Channel Cards illuminate.
Page 18
CITYLIGHT FIBRE CHANNEL CARD If any of the LEDs is not correctly illuminated/extinguished see Appendix A - Troubleshooting for possible causes. NOTE: During commissioning most faults are associated with bad/wrong cabling, dirty connectors, incorrect patching, loss of power, or excessive power budget. The hardware installation is now complete.
CITYLIGHT FIBRE CHANNEL CARD 4. DIAGNOSTIC LEDS COLOR CONDITION DATA GREEN USER DATA PRESENT ON THE LOCAL PORT. REM F THE SINGLE-MODE FIBER LINK TO THE FAR END FIBRE CHANNEL TRANSCEIVER HAS A FAULT. THE FAULT LIES IN THE PATH FROM THE TRANSMITTER OF THIS CARD TO THE FAR END CARD RECEIVER.
CITYLIGHT FIBRE CHANNEL CARD 5. SWITCH POSITIONS User Interface Backplane Connector Optical/Link Interface R = Remote L = Local Factory Test Must be set as shown Figure 4 - Switch Positions...
Page 21
CITYLIGHT FIBRE CHANNEL CARD SWITCH POSITION FUNCTION LOCAL (OFF) THERE IS NO SNMP CARD PRESENT AT EITHER END OF THE LINK. ONE CARD ON THE LINK MUST BE SET TO ‘L’ (LOCAL) AND THE OTHER SET TO ‘R’ (REMOTE). REMOTE (ON) IF AN SNMP CARD IS PRESENT AT EITHER END OF THE LINK SET BOTH CARDS TO REMOTE.
CITYLIGHT FIBRE CHANNEL CARD APPENDIX A - TROUBLESHOOTING PROBLEM POSSIBLE CAUSE THE LINK LED IS NOT LIT THE CITYLIGHT FIBRE CHANNEL CARD IS NOT RECEIVING POWER. CHECK THAT THE CARD IS CORRECTLY INSERTED INTO THE CHASSIS AND THAT POWER IS CORRECTLY SUPPLIED TO THAT CHASSIS.
Page 23
SHORT HAUL UNIT AND 0DBM FOR THE HIGH POWER UNIT. If, after going through the troubleshooting section, you fail to resolve your problem and require more help, please contact Black Box Technical Support at 724-746- 5500 with the following information: Unit type.
CITYLIGHT FIBRE CHANNEL CARD APPENDIX B - GLOSSARY OF TERMS GIGABIT DATA TRANSFER AT 1062 MEGABITS PER SECOND. LOCAL AREA NETWORK. LIGHT EMITTING DIODE. MANAGEMENT INFORMATION BASE. THIS IS A TEXT DESCRIPTION OF A MANAGED DEVICE WRITTEN IN ABSTRACT SYNTAX NOTATION 1 (ASN1) THAT IS USED WITH SNMP MANAGEMENT SYSTEMS.