Advertisement
Quick Links
Fixed Camera Quick Start Guide
Document Number 1012610 Version D
Important Safety Instructions
1.
Read these instructions.
2.
Keep these instructions.
3.
Heed all warnings.
4.
Follow all instructions.
5.
Install in accordance with the manufacturer's instructions.
6.
Do not defeat the purpose of the polarized or grounding-type plug.
A polarized plug has two blades with one wider than the other. A
grounding type plug has two blades and a third grounding prong.
The wide blade or the third prong is provided for your safety. If the
provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
7.
Use only with the tripod or bracket specified by the manufacturer, or
sold with the apparatus.
8.
Installation of the equipment must comply with local and national
electrical codes.
9.
This product must be connected to a Power Over Ethernet IEEE
802.af compliant power source or a UL Listed "Class 2" power supply
rated 12-24 V DC or 24 V AC minimum 13 W or 0.54 A.
10. Operating the camera at voltage levels outside the specified range
may result in permanent damage to the unit and void the product
warranty.
11. Clean the camera lens only with Kodak lens cleaning paper.
12. Failure to follow the proper procedure may cause permanent
damage to the camera and void the product warranty.
©Copyright 2013, CBC AMERICA, Corp. - All rights reserved. The contents of this document may not be reproduced in whole or in part without the written
DEVICE SENSITIVE TO ELECTROSTATIC DISCHARGE
The camera electronics and electronic interfaces are sensitive to
electrostatic discharge. Please follow appropriate ESD procedures when
handling the camera and during installation. For PoE installations, Ganz
strongly recommends the use of STP cabling and an earth grounded end
point to ensure proper ESD immunity. For AC or DC powered installations,
a properly earth grounded power source is strongly recommended.
To ensure a proper earth ground (between the Ganz Thermal camera and a
PoE switch) Ganz strongly recommends the use of Shielded Twisted Pair
(STP) cabling. Installations of Ganz Thermal cameras using a STP cabling
and a properly earth grounded PoE switch are tested to comply with industry
immunity standards for Electro Static Discharge.
method may leave the camera at risk and void the warranty.
consent of the copyright owner.
November 2014
WARNING
CAUTION
Any other installation
Advertisement
Related Manuals for Ganz Thermal ZNT6-H
Summary of Contents for Ganz Thermal ZNT6-H
- Page 1 802.af compliant power source or a UL Listed “Class 2” power supply rated 12-24 V DC or 24 V AC minimum 13 W or 0.54 A. To ensure a proper earth ground (between the Ganz Thermal camera and a PoE switch) Ganz strongly recommends the use of Shielded Twisted Pair 10.
-
Page 2: What's In The Box
Ensure that you have the following package contents ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS Ganz Thermal Fixed Mount Camera with the Back Cover attached MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT and a brown Desiccant pack inside the cover for shipping WARRANTY OF ANY KIND. - Page 3 Suggested Tools for Analog Video (Fixed Mount): Coax Cable Coax Cable Cutter/Stripper BNC Connector Comparison between Old Base Mounts and New Hybrid Base BNC Crimping Tool Mount Recommended Tools Cable Glands and Power Blocks for the Ganz Thermal Fixed Mount 320x240 & 640x480 models www.ganzsecurity.com...
- Page 4 Fixed Camera Quick Start Guide November 2014 Securing for IP66 (PoE only) Slide the Ethernet cable through the threaded end of the cable sealing gland, with Orange O-Ring installed Measure approximately 4.5 inches of cable slack from the end of the cable to the rubber grommet of the sealing gland.
- Page 5 Fixed Camera Quick Start Guide November 2014 IP66 (Ethernet and AC/DC Power) Securing for IP66 (Analog & AC/DC Power – Fixed Mount 320x240 Push the gland housing over the cables & 640x480 Only) Slide the Coax cable through the threaded end of the cable sealing gland, with Orange O-Ring installed Slide the 2, 20 AWG power wires (and any RS-485 wires) through the back side of the cable sealing gland...
- Page 6 Fixed Camera Quick Start Guide November 2014 For all Configurations: Pull the cable(s) taut back through the IP Camera, exposing the thread of the cable sealing gland out of the base of the IP Camera Assemble the Electrical Nut back onto the gland and tighten the Nut securely until it is finger tight.
- Page 7 Fixed Camera Quick Start Guide November 2014 Fixed Mount Pin-Out RS-485: Connect wires to power block according to the Fixed Mount 320x240 & 640x480 Pin-Out Pins 1-3: Power (GND, 24V AC, 12-24 DC/24V AC) pin-out sown on the left (Fixed Mount 320x240 & Pins 3-4: RS-485 (POS, NEG) 640x480 only) 12.
- Page 8 Fixed Camera Quick Start Guide November 2014 The three possible configurations of the Fixed Mount Series Back Cover and White Desiccant Back Cover screws and Sealing Washer Camera with Base mount and Standard 4-Hole mount www.ganzsecurity.com...
- Page 9 Fixed Camera Quick Start Guide November 2014 Solar Shroud and Stem Bumpers Fixed Camera can be mounted on standard bracket (WB-1W) WARNING DEVICE SENSITIVE TO ELECTROSTATIC DISCHARGE Fully assembled Camera The camera electronics and electronic interfaces are sensitive to electrostatic discharge. Please follow appropriate ESD procedures when handling the camera and during installation.
- Page 10 Fixed Camera Quick Start Guide November 2014 CAUTION To ensure a proper earth ground (between the Ganz Thermal camera and a PoE switch) Ganz strongly recommends the use of Shielded Twisted Pair (STP) cabling. Installations of Ganz Thermal cameras using a STP cabling and a properly earth grounded PoE switch are tested to comply with industry immunity standards for Electro Static Discharge.
- Page 11 Fixed Camera Quick Start Guide November 2014 For More Information Category Online Location Ganz Thermal Fixed Camera www.ganzsecurity.com/manuals Documentation Ganz Thermal Fixed Camera www.ganzsecurity.com/support Support http://www.videolan.org/vlc/ VLC Media Player Congratulations!! Ganz Thermal Fixed Mount Series Camera Installation and Configuration is now complete. www.ganzsecurity.com...