Tel : (886-2) 2231-6789 , Fax :(886-2) 2231-5678 TABLE OF CONTENTS S E R V I C E W A R N I N G A. I M P O R T A N T S A F E T Y I N S T R U C T I O N B.
Contact the local dealer or the nearest PROVIEW branch office if you need help. A. IMPORTANT SAFETY INSTRUCTION Prior to using this service manual,please ensure that you have carefully followed all the procedures outlined in the user's manual for this product.
Page 4
For Model 786NS,986NS Series WARNING : This product included critical components which are essential for X-Radiation safety. See service manual for proper replacement.Maximum 2nd anode voltage must not exceed 30KV at any operating conditions. To measure 2nd voltage use high impedance meter connect (-) chassis, use a high voltage lead from (+) to 2nd anode.
1. Screen 2. Visible Image Area 3. Active Display Area 4. Synchronization Range Horizontal Vertical 5. Power Source 6. Power Consumption 7. Input Signal Video Sync. 8. Connection Type 9. Resolution 10. Color Temperature 11. Dimension (W×H×D) 12. Monitor Weight 13.
Page 6
1. Screen 2. Visible Image Area 3. Active Display Area 4. Synchronization Range Horizontal Vertical 5. Power Source 6. Power Consumption 7. Input Signal Video Sync. 8. Connection Type 9. Resolution 10. Color Temperature 11. Dimension (W×H×D) 12. Monitor Weight 13.
Page 7
1. Screen 2. Visible Image Area 3. Active Display Area 4. Synchronization Range Horizontal Vertical 5. Power Source 6. Power Consumption 7. Input Signal Video Sync. 8. Connection Type 9. Resolution 10. Color Temperature 11. Dimension (W×H×D) 12. Monitor Weight 13.
D. CONTROL LOCATION Font control panel One key type a. Power Switch b. Power Indicator c.Encoder d. Enhance Key Four key type a. Power Switch b. Power Indicator c. Exit d. +Adjust e. -Adjust f. Menu...
F. ADJUSTMENT PROCEDURE ﹟ Test Meter ITEM ﹡ Test Point Program Menu. ﹫ Pattern ﹟ Digital Voltmeter Adjust ﹡ D510 Negative ﹫ Crosshatch Pattern (31.5KHz,640x480) High Voltage ﹟ Digital Voltmeter Adjust ﹟ High Voltage Probe ﹡ Anode Cap-GND ﹫ Crosshatch Pattern (31.5KHz,640x480) Preset ﹫...
Page 12
ABL on the OSD menu. 1. Set the FREQ. to 55 (562NS) (777NS,772NS,572NS) (786NS,787NS,986NS) 2. Set the OSD to PROVIEW 3. Set the BURN to Disable 4. Set the TIME to 15 5. Set the DEFO to TDA9113/9112 TDA9115...
Page 13
﹟ Test Meter ITEM ﹡ Test Point Program Menu. ﹫ Pattern Dynamic ﹟ Oscilloscope Focus ﹡ FBT Pin14 Adjust ﹫ Full White (31.5KHz,640x480) Purity ﹫ Magenta color Adjust (31.5KHz,640x480) Static ﹫ Magenta color Convergence (31.5KHz,640x480) Adjust Operation 1. Set the contrast to MAX.,and adjustment Brightness to the raster just appear.
H. TROUBLE SHOOTING HINTS BRIGHT HOR. LINE APPEAR ON THE SCREEN NO POWER T501 (7) F501,D514 , 160 V ? D515,D516, D517 IC501 (7) > 14 V ? IC501(6) 14Vp-p ? D510 (-) 15.5V ? CIRCUIT SHORT CHECK CHECK IC501,R539, D505,ZD551 CHECK IC501,Q504...
Page 23
IC301 (2) CHECK LINE 12 V ? IC301 (4) CHECK -12V LINE -12 V ? IC301 (1) CHECK IC601 0.7 V IC301 (5) CHECK IC301 48 V CHECK CRT DY...
Page 24
RASTER CRT G1 Q710 (E) -20V~ -80V ? -0.6V ? HEATER CHECK VOLT B+ VOLT 6.3 V ? 7.2 V ? CHECK Deflection Horizontal 26KV ? CRT G2 CHECK 600V ? T701 FBT VIDEO CKT KR,KG,KB FAILURE VOLTAGE CHECK CRT TUBE IC901(4) -1.5V~-1.8V CHECK...
Page 25
DEFLECTIVE HOR. CKT Q703 (C) 1.0 ~ 1.2 NO RASTER Q703 (B) DRIVE PULSE Q702 (G) DRIVE PULSE CHECK IC601 CHECK 15V LINE 986N:T701(3) Voltage for each mode T701(3) B+ 31.5KHz 37KHz 48KHz 54KHz 104V 56KHz 111V 64KHz 127V 68KHz 139V 75KHz 153V...
Page 26
OFF MODE NO ROTATION FAILURE IC901(40) CHECK (41) H/V SIGNAL IC901(20) CHECK PS 0 0 V ? Q505 (C) CHECK 7.0 V ? CHECK CHECK Q511 (B) 0 V ? CHECK Q511 VESA STANDARD DPMS ITEM MODE NORMAL STAND BY SUSPEND IC901 IC901 PIN40,PIN41 SIGNAL.
Page 27
P903 CHECK OK ? Rotation Coil Q902 (c) CHECK 15 V ? 15V LINE R979 CHECK 7 V ? 7V LINE Q902 (B) CHECK Q903 (B) Q902 1.5~13V ? Q903 Q904 (B) CHECK 0~2.5V ? IC901 CHECK Q904...
Page 28
NO CHARACTERS OSD DOES NOT MISSING ONE WORK Example:Missing Green COLOR CRT KG RASTER IC203 (3) 39 V IC203 12 V ? IC201 (10) 5 V ? IC201 (7) CHECK I/P 0.7V IC201 (19) 0.4 V ? CHECK IC201 CHECK IC203 CHECK CHECK...
Example : Missing Green Condition : OSD on IC201 (19) IC201(24) OSD G 7V ? IC202 (3) CHECK M703 BLK ? IC202(6) CHECK 4.2V CHECK D203 I. REPLACEMENT PARTS LIST CHECK IC201...
Need help?
Do you have a question about the P6NS Series and is the answer not in the manual?
Questions and answers