Ericsson 5780 Technical Information
  1. Manuals
  2. Brands
  3. Ericsson Manuals
  4. Gateway
  5. 5780
  6. Technical information
Ericsson 5780 Technical Information

Ericsson 5780 Technical Information

Unlicensed lpwa gateway
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Unlicensed LPWA Gateway 5780
Technical information
USER GUIDE
1/1553-KRC 161 673 UEN Rev PB9

Advertisement

Table of Contents
loading

Related Manuals for Ericsson 5780

Summary of Contents for Ericsson 5780

  • Page 1 Unlicensed LPWA Gateway 5780 Technical information USER GUIDE 1/1553-KRC 161 673 UEN Rev PB9...

  • Page 2: Table Of Contents

    Required Tools ................6 Conditions ..................8 Unpack and Check Materials............8 Installation Alternatives Overview ........... 10 Accessories for Gateway 5780 ............ 10 Install Gateway ................17 Wall Installation ................17 Pole Installation for Wall plate and Support ......... 23 Install Support 6501 ..............
  • Page 3 Unlicensed LPWA Gateway 5780 Copyright © Ericsson AB 2017. All rights reserved. No part of this document may be reproduced in any form without the written permission of the copyright owner. Disclaimer The contents of this document are subject to revision without notice due to continued progress in methodology, design and manufacturing.

  • Page 4: Introduction

    Introduction This document describes how to install the Unlicensed LPWA Gateway 5780 on site. The Gateway 5780 can be installed on a wall or on a mast, using a Support 6501 with built-in AC power supply or a wall plate.

  • Page 5: Connectors

    Unlicensed LPWA Gateway 5780 Connectors Figure 4 Connectors Item Description Local Management Port (Local O&M), USB type B WWAN Diversity antenna port (Backhaul) WWAN Main antenna port (Backhaul) GNSS antenna port (GPS) LoRaWAN™ antenna port SIM card slot (WWAN backhaul option) RJ45 Socket for Ethernet (ETH backhaul) and optional PoE input.

  • Page 6: Safety Information

    Unlicensed LPWA Gateway 5780 Safety Information Make sure that the information in the below documents has been read and understood by the persons performing the procedures:  Personal Health and Safety Information [1]  System Safety Information [2] Preparing for Installation...
  • Page 7 Unlicensed LPWA Gateway 5780 Product Name Tool Electrostatic Discharge (ESD) wrist strap (static control wrist strap) Wire stripper 0.2–6.0 mm Side cutter Ear protection Eye protectors One of the following (Wall mounting): • Hammer drill 230 V AC • Cordless hammer drill, with 230 V AC charger...

  • Page 8: Conditions

    Unlicensed LPWA Gateway 5780 Conditions The conditions in this section must be fulfilled before work starts. 3.2.1 Before Going to the Site Before going to site, make sure below items are available:  Site access permission has been received. ...
  • Page 9 Unlicensed LPWA Gateway 5780 1. Examine the packaging for damage. If it is damaged, immediately register a complaint with the transport company. It is recommended that a photo of the damages be taken to improve the claim process. 2. Remove the straps from the corrugated box.

  • Page 10: Installation Alternatives Overview

    The GNSS active antenna and the RF cable must not be installed close to lightning conductors, which can carry currents from direct lightning strikes. The regulatory testing for Gateway 5780 was conducted with the stated antennas in Table 1 installed and present. To be in compliance with regulatory requirements Ericsson state that installers and users of this Gateway 5780 must only use antennas of a similar type and with the same or lower gain.
  • Page 11 OR WWAN backhaul. WWAN: see EM7355 above in table Note 1: The Gateway 5780 receiver is classified as a category 2 receiver as per definition in ETSI EN 300 220-1, ref. [4]. Note 2: Sierra Wireless module “model: 7355” has already been certified in USA and Canada, under FCC ID: N7NEM7355 and IC: 2417C-EM7355.
  • Page 12 Unlicensed LPWA Gateway 5780  Ericsson AB 2017 1/1553-KRC 161 673 UEN Rev PB9 2017-03-24 12 (45) Commercial in confidence...
  • Page 13 1. Integrated 115/230V AC power is possible with Support Frame 6501 (Ericsson product number KRY 901 345/1) and Gateway 5780 main unit. I.e. DC input on Gateway 5780 is fed from the Support frame 6501 (including a PSU). Note: This installation requires external fuse and circuit breaker. The recommended melting fuse type is gG-gL-gD in accordance with IEC 60269-1.
  • Page 14 Unlicensed LPWA Gateway 5780 5.1.2 Mechanical Gateway Installation 5.1.2.1 Wall mount installation Figure 7 Wall Mount 5.1.2.2 Pole mount installation Figure 8 Pole Mount  Ericsson AB 2017 1/1553-KRC 161 673 UEN Rev PB9 2017-03-24 14 (45) Commercial in confidence...
  • Page 15 Unlicensed LPWA Gateway 5780 5.1.3 Antenna Alternatives The examples below show some typical form factor antennas. Always follow the guidelines from Ericsson regarding the supported antenna solutions. 5.1.3.1 Small Form Factor Antennas, e.g. 2 dBi LoRa® antenna Figure 9 Dual 2 dBi antennas, LoRa®(A) and WWAN Backhaul 5.1.3.2...
  • Page 16 Unlicensed LPWA Gateway 5780 5.1.4 Power Alternatives 5.1.4.1 Support 6501 Figure 11 115/230 AC power alternative 5.1.4.2 Power over Ethernet Figure 12 Power over Ethernet alternative  Ericsson AB 2017 1/1553-KRC 161 673 UEN Rev PB9 2017-03-24 16 (45) Commercial in confidence...

  • Page 17: Install Gateway

    Unlicensed LPWA Gateway 5780 Install Gateway Wall Installation 6.1.1 Using Support 6501 The drilling overview for wall installation is shown below Figure 13 Drilling Overview for wall installation Steps To install the gateway using a wall installation, do the following 1.
  • Page 18 Unlicensed LPWA Gateway 5780 2. Insert a plug or an expander bolt into the hole. Plugs or expander bolts are not delivered with the unit. They must be specified by the site installation plan. 3. Insert a screw in the hole, leaving 10 mm of the screw pointing out from the wall.
  • Page 19 Unlicensed LPWA Gateway 5780 8. Insert a plug or an expander bolt into the hole. Plugs or expander bolts are not delivered with the unit. They must be specified by the site installation plan. 9. Hook the Support onto the screw.
  • Page 20 Unlicensed LPWA Gateway 5780 6.1.2 Using Wall plate The drilling overview for wall installation is shown below Figure 14 Drilling Overview Steps To install the gateway using a wall installation, do the following 1. Mark a hole in the wall for the upper hole position on the gateway, and drill a hole.
  • Page 21 Unlicensed LPWA Gateway 5780 5. Mark the holes using the two bottom holes in the Wall plate. Use a spirit level to make sure the Support is in horizontal level. 6. Unhook the Wall plate from the wall. 7. Drill holes in the wall at the markings 8.
  • Page 22 Unlicensed LPWA Gateway 5780 10. Insert screws with flat washers in the holes. 11. Tighten the screws per the recommendations given by the site installation plan. 12. Hook the gateway onto the wall plate. 13. Fold down the gateway. 14. Tighten the screws to secure the gateway to the wall plate.

  • Page 23: Pole Installation For Wall Plate And Support

    Unlicensed LPWA Gateway 5780 Pole Installation for Wall plate and Support Steps To install the gateway using a pole installation, do the following: 1. Fit the pole clamps to the Support or wall plate. 2. Mount the pole clamps around the pole in the desired position.

  • Page 24: Install Support 6501

    Unlicensed LPWA Gateway 5780 Install Support 6501 “For permanently connected equipment, a readily accessible disconnect device shall be incorporated external to the equipment”. “The equipment shall be supplied from an external power supply source in compliance with the clause 2.5 of the standard IEC 60950-1”.
  • Page 25 Unlicensed LPWA Gateway 5780 5. Close the installation hatch, and tighten the screws. 6. Hook the gateway onto the support. 7. Fold down the gateway. 8. Tighten the screws to secure the gateway to the support.  Ericsson AB 2017...

  • Page 26: Connecting The Cables

    Unlicensed LPWA Gateway 5780 Connecting the Cables This section describes how to connect the power cable, antenna cables, and PoE cables to the gateway. The cable connecting order is as follows: 1. Grounding Cable 2. Power Cable 3. Antenna Cables 4.
  • Page 27 Unlicensed LPWA Gateway 5780 6.4.2 Connecting the Cables 1. Remove the front cover: Loosen the two screws holding the front cover in place. Torque of 200 +/- 15 Ncm shall be applied for the screws when lid is replaced. Lift the near end of the front cover ...
  • Page 28 Unlicensed LPWA Gateway 5780 Remove the cover by pulling it towards you Lift the cover out of the way and let it hang on the rubber strap  Ericsson AB 2017 1/1553-KRC 161 673 UEN Rev PB9 2017-03-24 28 (45)
  • Page 29 Unlicensed LPWA Gateway 5780 6.4.3 Connecting Backhaul Ethernet connection or 3G/LTE to be used as backhaul. For WWAN backhaul WWAN antenna and SIM card must be used. See 6.4.4 for SIM card and 6.4.5 Ethernet LAN. 6.4.4 3GPP SIM card SIM card to be installed according to picture below.
  • Page 30 Unlicensed LPWA Gateway 5780 6.4.6 Connect the power cable: a) On the right-hand strain relief, undo the right-hand screw  Ericsson AB 2017 1/1553-KRC 161 673 UEN Rev PB9 2017-03-24 30 (45) Commercial in confidence...
  • Page 31 Unlicensed LPWA Gateway 5780 b) Loosen the left-hand screw. c) Turn the strain relief clockwise.  Ericsson AB 2017 1/1553-KRC 161 673 UEN Rev PB9 2017-03-24 31 (45) Commercial in confidence...
  • Page 32 Unlicensed LPWA Gateway 5780 d) Insert the power cable connector into the port. e) Press down the cable into the opening in the gasket.  Ericsson AB 2017 1/1553-KRC 161 673 UEN Rev PB9 2017-03-24 32 (45) Commercial in confidence...
  • Page 33 Unlicensed LPWA Gateway 5780 f) Turn the strain relief counter clockwise g) Fasten the right-hand screw, making sure that the strain relief holds the cable in place and then fasten the left-hand screw.  Ericsson AB 2017 1/1553-KRC 161 673 UEN Rev PB9...

  • Page 34: Connecting Antennas

    Unlicensed LPWA Gateway 5780 Connecting Antennas Antenna connections for the gateway as picture below indicates Figure 18 Antenna connection for jumper cable Connector Description WWAN Diversity antenna port (Backhaul) WWAN Main antenna port (Backhaul) GNSS antenna port (GPS) LoRaWAN™ antenna port ...

  • Page 35: Management

    NW controller address setting – what NW server to connect to  Set FW update credentials – FW version to be fetched update of Gateway 5780 Notifications from the Gateway 5780 are sent using SNMP v2 and SNMP v3 traps. SNMP can be accessed both locally and remotely: ...
  • Page 36 Operation and Maintenance configuration. The Users of Gateway 5780 are the physical sensors that connect to it and as such they will never have any access to be able to change any configuration of Gateway 5780 so that it can operate outside of the radio parameters under which the Gateway has been certified and approved for correct use.

  • Page 37: Mobile Network Subscription (Wwan Backhaul Option)

    USA and Canada of conducted output power maximum 27.5dBm and EIRP maximum 36dBm. The actual maximum EIRP values of Gateway 5780 are therefore defined by the maximum conducted output value + the compensation value (antenna gain + feeder cable path loss,) which is input during installation.
  • Page 38 Unlicensed LPWA Gateway 5780 7.4.1 Remote fault handling Via SNMP O&M the Gateway 5780 unit can be accessed for fault analysis and trouble shooting. Examples of supported trouble shooting functionality:  Operational state  Alarm state  Local logs 7.4.2 LED handling Three LEDs indicating current operational state of the Gateway 5780.

  • Page 39: Performance Management

    Measurements for LoRaWAN™ network performance. The Performance data sent upstream to network performance monitoring system. Hardware management The Gateway 5780 is a single hardware unit and is also the replaceable part.  Ericsson AB 2017 1/1553-KRC 161 673 UEN Rev PB9...

  • Page 40: Software Management

    If the upgrade fails an alarm will be sent and automatically roll back will be triggered. Security Management The Gateway 5780 is tamper protected for a secure and trustworthy deployment in a network. The Gateway 5780 network data service and the operation and maintenance is highly secure to protect from unauthorized access.

  • Page 41: References

    Unlicensed LPWA Gateway 5780 References Personal Health and Safety Information 124 46-2885 Uen System Safety Information 124 46-2886 Uen Grounding Guidelines for RBS Sites, 23/1551-LZA 701 6009 ETSI EN 300 220-1, Short Range Devices (SRD) operating in the frequency range 25 MHz to 1 000 MHz; Part 1: Technical...

  • Page 42: Appendix A. Fcc/Ised Regulatory Notices

    Appendix A. FCC ISED Regulatory notices Modification statement Ericsson has not approved any changes or modifications to this device by the user. Any changes or modifications could void the user’s authority to operate the equipment. Ericsson n’approuve aucune modification apportée à l’appareil par l’utilisateur, quelle qu’en soit la nature.
  • Page 43 Unlicensed LPWA Gateway 5780 FCC Class B digital device notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

  • Page 44: Appendix B. European Union, Eu Declaration Of Conformity

    1999/5/CE. Icelandic Hér með lýsir Ericsson AB yfir því að Gateway 5780 er í samræmi við grunnkröfur og aðrar kröfur, sem gerðar eru í tilskipun 1999/5/EC  Ericsson AB 2017...
  • Page 45 Slovak požiadavky a všetky príslušné ustanovenia Smernice 1999/5/ES. Slovenian Ericsson AB izjavlja, da je ta Gateway 5780 v skladu z bistvenimi zahtevami in ostalimi relevantnimi določili direktive 1999/5/ES. Spanish Por medio de la presente Ericsson AB declara que el Gateway 5780 cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.

Table of Contents