Advertisement
Quick Links
EMPRESS ROUND BABY BASSINET
Assembly Instructions. Adult Assembly Required.
Read all instructions before use.
This manual is part of the product and
must be kept for future reference.
MODEL NUMBER*:
83951 - White/Ecru
with Belt
VERSION CODE*:
1.0/0115/TG
* These numbers are needed if
replacement parts are requested
If you need product parts,
see below or Page 2!
FOR REPLACEMENT PARTS:
Go to our web site: http://www.badgerbasket.com/parts
Or scan QR code at right with your smartphone
1.0/0115/TG
Advertisement
Related Manuals for Badger Basket 83951
Summary of Contents for Badger Basket 83951
- Page 1 Assembly Instructions. Adult Assembly Required. Read all instructions before use. This manual is part of the product and must be kept for future reference. MODEL NUMBER*: 83951 - White/Ecru with Belt VERSION CODE*: 1.0/0115/TG * These numbers are needed if...
-
Page 2: Before You Begin Assembly
Iron on lowest setting for polyester/cotton. Secure all snaps/straps/tabs before washing. White Fitted Sheets (2/pack) - Model #83998 Badger Basket Company, PO Box 227, Edgar, WI 54426-0227 USA • Web: www.badgerbasket.com Toll-Free (Mon-Thurs 7:30 AM-3:30 PM CST): 1-800-236-1310 Phone: 1-715-352-2311 • Fax: 1-715-352-3163... - Page 3 ALWAYS use a or waterproof pad should be used under the baby. • Use ONLY the bedding designed for this bassinet from Badger Basket Company. Secure the bedding as instructed in this manual and check regularly to ensure it remains properly attached.
-
Page 4: Tool Required
Ax2 - Right Leg Bx2 - Left Leg Cx2 - Leg Brace Ex1 - Bed Bottom Dx2 - Shelf Rail Fx1 - Bed Body Gx4 - Wheel Hx1 - Vinyl/Foam Pad Ix1 - Fitted Fabric Sheet Lx8 - Short Bolt with Regular Nut Jx1 - Fabric Liner/Skirt Kx1 - Mesh Shelf... - Page 5 - Carefully note the angle and positions of the RIGHT and LEFT LEGS (PARTS A and B). If assembled incorrectly, you will not be able to do STEP 4. - Use WRENCH and SCREWDRIVER to tighten all bolts and nuts firmly, but do not overtighten - Repeat this step to assemble the second set of legs ×2...
- Page 6 3.1 - Remove and discard the 3.2 - Unfold the BED BODY (PART F) plastic caps used for shipping PUSH IT 3.3 and 3.4 - Connect the frame ends to form a circle. The two locking silver buttons MUST snap through the holes to secure the frame! You may find it easiest to hold the frame perpendicular to the floor and apply downward pressure to help the parts snap into place.
- Page 7 - FOR STEPS 5 AND 6: get all of the BOLTS (PART L) started, then you may need to push on the legs and adjust the body to align all the tabs to secure them. - Use WRENCH and SCREWDRIVER to tighten all bolts and nuts firmly, but do not overtighten - Secure ALL FOUR bolts (PART L) in this step.
- Page 8 - Turn the bassinet upside down on a carpeted surface or on top of the product carton so as not to soil or damage it in this step. - After firmly inserting the wheels, turn the bassinet right side up again to continue assembly...
- Page 9 - Dress the FABRIC LINER/SKIRT (PART J) onto the BED BODY (PART F). - Insert the VINYL/FOAM PAD (PART H) into the FABRIC FITTED SHEET(PART I) and then place them into the bassinet. - Thread the FABRIC BELT (PART N) through the belt loops on the FABRIC LINER/SKIRT (PART J) and tie in a bow as shown.