Advertisement
Quick Links
RZR3 DIE CAT ALUMINUM EXIT SIGN / FIXTURE
INSTALLATION AND OPERATING
When using electrical equipment, basic safety precautions should always be followed including the
following:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
1. DO NOT use outdoors.
2. DO NOT mount near gas or electric heaters.
3. Equipment should be mounted in locations and at heights where it will not be
readily subject to tampering by unauthorized personnel.
4. The use of accessory equipment is not recommended by the manufacturer.
Use of such equipment may cause an unsafe condition.
5. DO NOT use this equipment for other than intended use.
6. Conduct periodic visibility tests in accordance with the applicable installation
code (such as NFPA 101).
7. Supply connections MUST be made inside the junction box.
8. Install using recommended junction box ONLY.
9. Servicing of this equipment should be performed by a qualified service personnel.
10. Install sign indoors only where not exposed to direct unfiltered sunlight, liquid
spray or temperatures outside of the range of 10 C to 40 C.
11. Before installing unit, disconnect power at breaker panel.
SAVE THESE INSTRUCTIONS
CONSERVER LA FICHE D'INSTRUCTION
Z410139 Rev E
RAZOR-3 SERIES
INSTRUCTIONS
IMPORTANT SAFEGUARDS
2575 Metropolitan Drive • Trevose • PA 19053 U•S•A
Telephone: (215) 244-4204 • Fax: (215) 244-4208
o
o
Page 1
Advertisement
Related Manuals for Evenlite RAZOR-3 SERIES
Summary of Contents for Evenlite RAZOR-3 SERIES
- Page 1 RAZOR-3 SERIES RZR3 DIE CAT ALUMINUM EXIT SIGN / FIXTURE INSTALLATION AND OPERATING INSTRUCTIONS IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be followed including the following: READ AND FOLLOW ALL SAFETY INSTRUCTIONS 1. DO NOT use outdoors.
- Page 2 INSTALLATION INSTRUCTIONS This Exit Sign is designed to be mounted to a junction box (supplied by others). It can be either back, top or side mounted. The single face unit back mounts to a standard 4” Square (4S) junction box. Dual circuit options will require a deep junction box. DEPTH: Standard J-box Depth = 1 ½”...
- Page 3 3. To remove directional indicators, remove light guide assembly and diffusers and set aside. Support front cover and knock out desired indicator(s). Knock out desired directional indicators (chevrons) supporting the front panel as shown. Figure 4: Removing the directional indicators (chevrons) Before installing unit, disconnect power at breaker panel 4.
- Page 4 SECTION 2: BACK MOUNT INSTALLATION (SINGLE FACE SIGN) 1. Secure spider plate to junction box. Route transformer’s secondary leads through center knockout of the rear panel. 2. Place the filler plates in rear panel as per Detail B. 3.Terminate transformer leads to light guide assembly, per Detail A below. 4.
- Page 5 SECTION 3: CANOPY MOUNT (SINGLE OR DOUBLE FACE SIGNS) 1. Secure spider plate to junction box. Guide transformer secondary leads through canopy and connect to sign. 2. Secure canopy to sign and then fasten to spider plate. If an optional security cover will be utilized, it must be assembled to sign prior to securing the canopy to the sign.
- Page 6 SECTION 4: MASTER - REMOTE SIGN The Master - Remote product (RZMR3) is supplied with 2 signs. The master sign (Figure 11) is provided with a system battery, spider plate assembly (for power) and an option connector used to connect the two signs. The remote sign (Figure 12) is assembled in the same manner as the master sign, without a spider plate assembly.
- Page 7 Route remote wire from master sign to remote sign via the knock out in the rear panel. The remote sign can be mounted to a junction box (as shown) or secured safely to the wall using anchors. The remote option printed circuit assembly should be installed into the sign as shown below. The text legend on the PCA should be visible when looking at the rear of the light guide assembly.
- Page 8 SECTION 7: OPTIONS FLASHER/ FIRE ALARM Battery Backup Emergency signs that are equipped with the FLASH in Fire Alarm EMERGENCY MODE OPTION will automatically flash in the emergency Remote Lamp mode but not flash on AC operation. AC Only exit signs that are equipped with the flash option will flash continuously while power is supplied.
- Page 9 SELF TESTING/ SELF DIAGNOSTIC OPERATING INSTRUCTIONS The unit meets the requirement of NFPA 101 for Periodic Testing of Emergency Lighting Equipment. It provides visual indication of unit malfunctions including: Battery Fault Charger Fault Transfer Fault Lamp Fault TABLE: STATUS INDICATIONS FUNCTION STATUS DISPLAY ACTION...
- Page 10 THIS PAGE INTENTIONALLY LEFT BLANK...
- Page 11 THIS PAGE INTENTIONALLY LEFT BLANK...
- Page 12 THIS PAGE INTENTIONALLY LEFT BLANK...
Need help?
Do you have a question about the RAZOR-3 SERIES and is the answer not in the manual?
Questions and answers