Operation Manual LA810E 18.1"Ultra High Resolution Digital Interface LCD Monitor LA810E.p65 2000/8/14, PM 03:02...
Page 2
Netzstecker nicht in Ihre Steckdose passen sollte, wenden Sie sich an einen Elektriker, damit dieser die veraltete Steckdose auswechselt. 10. Stellen Sie keine Gegenstände auf das Netzkabel, und verlegen Sie es so, daß niemand hierüber stolpern kann. LA810E.p65 2000/8/14, PM 03:01...
Page 3
Bedienungsanleitung besprochen werden, da eine Fehleinstellung anderer Regler das Gerät beschädigen kann und aufwendige Reparaturarbeiten die Folge wären. Falls das Produkt heruntergefallen ist, oder das Gehäuse beschädigt wurde. Wenn das Gerät einen außergewöhnlichen Betriebszustand aufweist, der reparaturbedürftig ist. LA810E.p65 2000/8/14, PM 03:01...
It is essential that only the supplied power cord be used. Use only shielded cables to connect ATI devices to this equipment. You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. LA810E.p65 2000/8/14, PM 03:01...
Also, make sure that the total of all products plugged into the wall outlet does not exceed 15 amperes. LA810E.p65 2000/8/14, PM 03:01...
Page 6
16. Apparaten skall anslutas till jordat uttage när skyddsklenspenning- Sutgången till ett nät som passerar såväl ojordat som jordat miljö. (For Nordic Only) 17. This LCD monitor should use AC adaptor, model PA1250,PC1255, PP1250 or PS1250. LA810E.p65 2000/8/14, PM 03:01...
Page 8
Universal auto-switching power adapter • TCO’99 Compliant (Optional) • VESA DPMS compliant • USB with one up stream port and four down stream ports • VESA DVI Digital Interface Standard • Build in Speakers (0.5W x 2) LA810E.p65 2000/8/14, PM 03:02...
Page 9
LCD monitor • ATI Rage Fury Pro (or Hercules 3D PROPHLT DDR-DVI) Video Adapter • AC-DC power adapter • This manual • Power Cord • Audio cable (option) • ATI (or Hercules) Installation Software CD-ROM or diskettes LA810E.p65 2000/8/14, PM 03:02...
Page 10
ATI Rage Fury Pro digital LCD video card is available on the ATI Installation Software CD-ROM. If you do not feel comfortable performing this installation, consult a qualified computer technician for assistance. LA810E.p65 2000/8/14, PM 03:02...
Plug the power cable into the wall outlet. Plug the other end of the power adapter into the DC-IN jack of the monitor. Signal Cable Connection Plug the PanelVision digital signal cable into the digital signal connector on the video display card. LA810E.p65 2000/8/14, PM 03:02...
Page 12
You are now ready to use your PanelVision monitor. Switch on the power to both the monitor and to your computer. If you need to make any adjustments to the displayed image, refer to the Operation Chapter. If the image does not display or displays improperly, refer to Troubleshooting. LA810E.p65 2000/8/14, PM 03:02...
To adjust screen brightness press the + key to increase brightness or the - key to decrease brightness. Volume Control To adjust audio volume press the + key to increase volume or the - key to decrease volume. LA810E.p65 2000/8/14, PM 03:02...
To implement DDC, turn on your computer first and then your monitor. Windows will create a table of your monitor and video adapter’ s maximum refresh rates at different possible resolutions. LA810E.p65 2000/8/14, PM 03:02...
Do not use abrasive pads or solvents such as alcohol based cleaners or benzene to clean your monitor • Always handle your PanelVision monitor with care when moving it. LA810E.p65 2000/8/14, PM 03:02...
• Check that the computer power switch is On • Check that the monitor is not in Suspend mode. Color is Abnormal Is the signal cable properly attached? • Check the video signal cable. LA810E.p65 2000/8/14, PM 03:02...