Sealey VS862 Instructions Manual
  1. Manuals
  2. Brands
  3. Sealey Manuals
  4. Medical Equipment
  5. VS862
  6. Instructions manual
Sealey VS862 Instructions Manual

Sealey VS862 Instructions Manual

Vag code reader and reset tool
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
SOFTWARE VERSIONS > V2.6 (V1.9 SERIAL)
1. Safety Precautions and Warnings........................................2
2. Product Information .............................................................2
2.1
Tool Description ..........................................................3
2.2
Specifications ...............................................................4
2.3
Accessories Included...................................................4
2.4
Navigation Characters................................................4
2.5
Keyboard .....................................................................5
2.6
Power............................................................................5
2.7
Product Setup ..............................................................5
2.8
Vehicle Coverage.......................................................10
3. Operating Instructions........................................................10
3.1
VW/AUDI Diagnostics..............................................10
3.2
OBDII/EOBD Diagnostics........................................16
3.3
Oil Service..................................................................20
4. Warranty and Service .........................................................34
4.1
Limited One Year Warranty ...................................34
4.2
Service Procedures....................................................34
< V2.6 USB-V1.9 SERIAL SOFTWARE
< V2.6 USB-V1.9 SERIAL SOFTWARE
Model No: VS862
Table of Contents
Instructions For:
VAG Code Reader
and Reset Tool
1
1
V

Advertisement

Table of Contents
loading

Related Manuals for Sealey VS862

Summary of Contents for Sealey VS862

  • Page 1 Instructions For: VAG Code Reader and Reset Tool Model No: VS862 SOFTWARE VERSIONS > V2.6 (V1.9 SERIAL) Table of Contents 1. Safety Precautions and Warnings........2 2. Product Information .............2 Tool Description ............3 Specifications ...............4 Accessories Included...........4 Navigation Characters..........4 Keyboard ..............5 Power................5...

  • Page 2: Safety Precautions And Warnings

    NEUTRAL (for manual transmission) and make sure the parking brake is engaged. • Wear approved eye protection. A full range of personal safety equipment is available from your Sealey dealer. • 3Wear suitable clothing to avoid snagging. Do not wear jewellery and tie back long hair.

  • Page 3: Product Information

    2. Product Information 2.1 Tool Description ① LCD DISPLAY -- Indicates test results. Backlit, 128 x 64 pixel display with contrast adjustment. ② Y BUTTON -- Confirms a selection (or action) from a menu. When a DTC’s definition covers more than one screen, it is used to move down to the next screen for additional data.

  • Page 4: Specifications

    UP SCROLL BUTTON -- Moves up through menu and ④ submenu items in menu mode. When more than one DTC is retrieved, moves up through the current screen to the previous screens for additional DTCs and definitions. DOWN SCROLL BUTTON -- Moves down through menu ⑤...

  • Page 5: Keyboard

    4) “pd” -- Identifies a pending DTC when viewing DTCs. 2.5 Keyboard No solvents such as alcohol are allowed to clean the keypad or display. Use a mild nonabrasive detergent and a soft cotton cloth. Do not soak the keypad as the keypad is not waterproof. 2.6 Power The external power of the scan tool is provided via the vehicle Data Link Connector (DLC).

  • Page 6: Contrast Adjustment

    System Setup ►1) Contrast 2) Display Test 3) Keyboard Test 2) From the Main Menu: Use the UP/DOWN Scroll Buttons to select System Setup and then press the Y button. Follow the instructions to make adjustments and settings as described in the following setup options.
  • Page 7 From the Contrast menu, use the UP/DOWN scroll buttons to increase or decrease the contrast. Contrast Contrast （45%） to change 2) Press the Y button to save your selection and return to previous menu. 3) Press the N button to return to previous menus. Display Test The Display Test is used to check the LCD display.
  • Page 8 Display Test Press [Y] to test. Look for missing spots in characters. Press <N> to return. 3) When completed, press the N button to return. Keyboard Test The Keyboard Test is used to verify that the keys are functioning properly. 1) Use the UP/DOWN scroll buttons to select Keyboard Test from System Setup menu, and then press Y button.
  • Page 9 Keyboard Test Press any key to Start test to display name. Key: Double [N] to Return 3) Double press N to return to the previous menu. Unit of Measure The Unit of Measure function is used to change between metric and English unit of measurement.

  • Page 10: Vehicle Coverage

    2.8 Vehicle Coverage The V862 VW/AUDI Code Scanner is specially designed to work with most Volkswagen and Audis sold worldwide of 1990 or newer models. If a VW/AUDI has a 16-pin "OBD-II style" Data Link Connector (DTC), the code reader will certainly work. If it has an old- style 2x2 Data Link Connector (DTC), then it depends on whether there are 4 or 3 wires connecting to the pins.
  • Page 11 Main Menu ►1) VW/AUDI 2) OBDII/EOBD 3) Oil Service 4) System Setup Use the UP/DOWN scroll buttons to select the system from the Select System menu and press the Y button. Select System ►01) Engine 02) Auto Trans 15) Airbags 03) ABS Brakes 08) Auto HVAC 09) Cent.
  • Page 12 Select Read Codes from the Select Function menu and press the Y button. Select Function ►1) Read Codes 2) Erase Codes 3) ECU Information 4) Readiness Test If there are no Diagnostic Trouble Codes present, the display will indicate “NO CODES ARE STORED IN THE MODULE!”...
  • Page 13 16627 --100 01/10 CAN BUS ↓ Solenoid Valve (A) For Boost Pressure Control (N75): Malfunction: P0243 Erasing Codes CAUTION: Erasing the Diagnostic Trouble Codes may allow the scan tool to delete not only the codes from the vehicle’s on-board computer, but also “Freeze Frame” data and manufacturer specific enhanced data.
  • Page 14 Erase Codes Erase Trouble Codes! Are you sure? <YES> If you do not want to proceed with erasing the codes, press the N button to exit. A message of “command cancelled” will show up. If you do wish to proceed to erase the codes, then press the Y button.
  • Page 15 ECU Information VAG No.: 06A906032TF Component: Bosch 1.815VT 0020 Coding: 0008570 Imp: 0000 WSC: 000078 If there is no ECU Information available, a warning message shows on the display. Press the N button to return to previous menus. Readiness Test Important: The Readiness Test function is used to check the operations of the Emission System on OBD2/EOBD compliant vehicles.

  • Page 16: Obdii/Eobd Diagnostics

    2) Use the UP/DOWN scroll buttons, as necessary, to view the status of the following monitors: EGR Sys.-- EGR System Monitor O2 Sensor(s) -- O2 Sensors Monitor Catalyst -- Catalyst Monitor EVAP Sys. -- Evaporative System Monitor Heated O2 --O2 Sensor Heater Monitor Sec Air Inject -- Secondary Air Monitor A/C -- A/C system Monitor Catalytic Conv.
  • Page 17 If the “LINK ERROR” message does not go away, then there might be problems for the scan tool to communicate with the vehicle. Contact your local distributor or the Sealey’s customer service department for assistance. 8) After the vehicle protocol is displayed on the screen, press any key or wait about 2 seconds for the OBDII/EOBD DIAG.
  • Page 18 OBDII/EOBD DIAG. ►1) Read Codes 2) Erase Codes If there are no Diagnostic Trouble Codes present, the display will indicate “NO CODES ARE STORED IN THE MODULE!” If there are any Diagnostic Trouble Codes present, the Fault Codes and Pending Codes will be reported on the display. P0118 06/06 ISO9141...
  • Page 19 If the retrieved DTCs contain any manufacturer specific or enhanced codes, you will be prompted to refer to the CD DTC library or the vehicle service manual to view the DTC definitions. 10) If more than one DTC is found, use the UP/DOWN scroll buttons, as necessary, until all the codes have been shown up.

  • Page 20: Oil Service

    4) If you do wish to proceed to erase the codes, then press the Y button. 5) If the codes are cleared successfully, an “ERASE DONE!” confirmation will show on the display. Press any button to return to previous menus. 6) If the codes are not cleared, then an “ERASE FAILURE!”...
  • Page 21 If the “LINK ERROR” message does not go away, then there might be problems for the scan tool to communicate with the vehicle. Contact your local distributor or the manufacturer’s customer service department for assistance. A. Automatic Vehicle Detect Use UP/DOWN scroll button to select All, and press Y button. Oil Service ►1) All 2) Audi(up to 2000)
  • Page 22 Oil Type ►01) Fixed Service 02) Flexible-Gasoline 03) Flexible-Diesel Use UP/DOWN button to select oil type that your vehicle uses and press Y button. Select Function ►01) Oil Insp. Light 02) Set Insp. 1 03) Set Insp. 2 Different vehicle supports different oil service functions, so the displayed functions vary from one vehicle to another.
  • Page 23 Oil Service RESET OK! Press any key to cont. If the vehicle can not be detected automatically, following screen shows. You need to perform oil service setup manually. Oil Service Can’t Auto Detect! Please try others! Press any key to con. Wait a few seconds or press any key to start reading channel data.
  • Page 24 Min Mil. to Service Channel No (Mil) Current Value 9000 Set Value 9000 [N] = Next, [Y] = Save/Exit ] = Change Setup ︽ ︾ x/x to the upper right part of the screen indicates total number of supported service channels and the sequence of current channel.
  • Page 25 Oil Service Back Save Exit [Back] = Cont. to Set [Save] = Save Setup [Exit] = Cancel Setup If you want to continue to set values, use UP/DOWN scroll button to select Back and press Y button to return to continue setup.
  • Page 26 Oil Service 1) Auto Detect ►2) Longlife Oil 3) Non Longlife Oil 4) Set Insp. Interval Use UP/DOWN scroll button to select Service Reset from Long Life Oil menu, and press Y button. Longlife Oil ►1) Service Reset 2) Set Oil Type 3) View Oil Type Press any key to return to Long Life Oil menu.
  • Page 27 Set Oil Type ►1) Diesel 2) V6Tdi 3) Petrol 4) Non Longlife Oil Use UP/DOWN scroll button to select the oil type your vehicle uses. Press any key to return to Long Life Oil menu. Oil Type Reset RESET OK! Press any key to con.
  • Page 28 View Oil Type Non longlife Oil Press any key to con. Resetting Non Long Life Oil Service The Non Long Life Oil function is used to reset non Long Life oil service. To reset non Long Life oil service, use UP/DOWN scroll button to select Non Long Life Oil from the Oil Service menu, and press Y button.
  • Page 29 Service Reset RESET OK! Press any key to con. Setting Inspection Interval The Set Insp. Interval function is used to set oil service interval of different channels. Use UP/DOWN scroll button to select Set Insp. Interval, and press Y button. Oil Service 1) Auto Detect ►2) Longlife Oil...
  • Page 30 Manual Reading Channel Data… -Please Wait- Use UP/DOWN scroll button to change set value. Min Mil. to Service Channel No (Mil) Current Value 9000 Set Value 9000 [N] = Next, [Y] = Save/Exit ] = Change Setup ︽ ︾ Use N button to move to next setup screen. Mil.
  • Page 31 Oil Service Back Save Exit [Back] = Cont. to Set [Save] = Save Setup [Exit] = Cancel Setup Press any key to return to Main Menu. Manual Setup RESET OK! Press any key to con. If you want to continue to set values, use UP/DOWN scroll button to select Back and press Y button to continue to change...
  • Page 32 Main Menu 1) VW/AUDI 2) OBDII/EOBD ►3) Oil Service 4) System Setup Use UP/DOWN scroll button to select vehicle make, and press Y button to confirm. Oil Service 1) All 2) Audi(up to 2000) ►3) VW(up to 2000) 4) Seat(up to 2000) 5) Skoda(up to 2000) Use UP/DOWN scroll button to select vehicle model year, and press Y button to confirm.
  • Page 33 Select Function ►01) Oil Insp. Light 02) Set Insp. 1 03) Set Insp. 2 Wait a few seconds till the following screen appears. Oil Service RESET OK! Press any key to con. If a message “Service reset failed!” comes up, repeat the procedure from Step 3 or use Auto Detect to detect service automatically.

  • Page 34: Warranty And Service

    4. Warranty and Service 4.1 Limited One Year Warranty Sealey warrants to its customers that this product will be free from all defects in materials and workmanship for a period of one (1) year from the date of the original purchase, subject to the following terms and...

Table of Contents