Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Starway LASERLAB 200
Summary of Contents for Starway LASERLAB 200
- Page 1 User Manual LASERLAB 200 LASERLAB 200...
- Page 2 The following is a guide to installing your new LaserLab 200. Please remember that due care and attention should always be taken when working with LASERS and electricity. We recommend that a professional installer and a licensed Electrician install your projector. LASERLAB 200...
-
Page 3: Introduction
If you have questions about how to operate the projector safely, please contact your Starway reseller. To protect yourself and others from electric shock •... - Page 4 • One 3m, 3-pin IEC mains (power) cable • One 1m USB cable • One 9-pin (DB9 Male) Interlock dongle (Must be connected to the projector for the laser to operate. • One 128MB SmartMedia Card LASERLAB 200...
-
Page 5: Ac Power
If you find that you have an unearthed power supply, you will need to connect an earth before installing the projector. We recommend that you contact either at your own a Technician or a Licensed Electrician to do this. Alternatively, LASERLAB 200... - Page 6 NOTE: when in the “ON” position, the key cannot be removed. 3. Switch the computer on. You now can continue with the installation of your new laser projector. 4. Please note you will need to connect and secure LASERLAB 200...
-
Page 7: Installation
0.3 meters (12 inches). When installing the projector next to a lighting fixture, avoid illuminating the projector. It will create unnecessary heat and may void the warranty as well as result in undesired operation. Truss or other overhead mounting LASERLAB 200... - Page 8 Copy the files from the CD-ROM into that folder. 3. Connect the USB cable from your PC to the Projector. 4. A screen will appear on your PC asking for the drivers. 5. Select the option “Install from a specific location” LASERLAB 200...
- Page 9 User Manual 6. In the next screen click the “Browse” button and find the folder titled “USB Driver”, select that folder and click “OK” LASERLAB 200...
- Page 10 All of these feature are also available via DMX-512. 14. You can link cues together to create a sequence of effects. Simply right click on the desired first cue, select “Link” and LASERLAB 200...
- Page 11 “X” and “Y” knobs on the back of the unit. 18. Whenever you edit cues or make changes to your workspace file, you should always save them under a new file name for later use. ILDA Test Pattern LASERLAB 200...
-
Page 12: Sound Active
I.E. For Pangolin users you will need to adjust color response through the “Palettes” feature. Compliance Statement Compliance Statement Your new LaserLab 200 Projector has been designed to comply with FDA and IEC Standards for it classification. The LaserLab 200 Projector is a Class IIIB laser LASERLAB 200... - Page 13 There are no user serviceable parts inside. Tampering or removing warranty seals will void your products limited warranty. A Combo label with the Product Model Number, Serial Number, Date of Manufacture, Laser Light Warning Label, Warranty Void Label and Interlocked Housing Label LASERLAB 200...
-
Page 14: Dmx Control
Address your projector accordingly so that it corresponds with projector’s profile address on your controller. Apply power to both the controller and projector. You are now able to control the projector via your controller. LASERLAB 200... - Page 15 DMX-512 is a simple to use control protocol that allows you to control up to 512 channels at any one time. The LaserLab 200 Projector uses 14 Channels to control its functions. In order to communicate with the projector you will need to assign a start address for the first channel of the projectors profile.
- Page 16 User Manual This switch is to be turned on when using DMX LASERLAB 200...
- Page 17 4. After you upload this change to the SmartMedia card and cycle the power to the projector, you will see this cue play automatically after power up. 5. If you wish to play multiple cues automatically simply link the cues in the desired order. LASERLAB 200...
-
Page 18: Troubleshooting
4. It should click into place. PLEASE NOTE: USB CABLES LONGER THAN 2 METERS ARE NOT SUGGESTED AS THE IEEE STANDARD FOR USB ALLOWS FOR A DISTANCE OF ONLY ONE METER (THREE FEET) LONGER CABLES MAY RESULT IN POOR OPERATION OR ERRORS. LASERLAB 200... -
Page 19: Technical Specifications
Model: LaserTech 250 Laser Type: LD & DPSS Laser Life: 6,000 to >10,000 Hours Output Type: CW Cooling: TEC Thermal Electronically Cooled Color: 200mW 532nm Green Output: 200mW GREEN Modulation: Analog AC Power: 80-250V AC Self Switching Consumption: 2.5A LASERLAB 200...
Need help?
Do you have a question about the LASERLAB 200 and is the answer not in the manual?
Questions and answers