Page 1
ASSEMBLY INSTRUCTIONS CHECKING LIST FOR INSPECTION AFTER ASSEMBLY...
Page 2
CONTENTS ASSEMBLY INSTRUCTIONS ..................1 TO THE DEALER..................... 1 SAFETY ........................1 UNPACKING AND CHECKING PARTS ..............2 Unpacking Iron Crate......................2 The Accessories Packaged Together with Tractor ............2 Contents of Accessory Case .................... 3 Contents of Nylon Bag Attached with the Accessory Case ..........5 ASSEMBLY......................
ASSEMBLY INSTRUCTIONS ASSEMBLY INSTRUCTIONS TO THE DEALER (3) Working clothes which may 1. This manual contains procedures intended to assist be pinched or caught in the the dealer in unpacking and assembling the product equipment must not be worn. before delivering to the customer. Loose clothing can cause The customer's purchase is based on confidence in serious injury or death.
UNPACKING AND CHECKING PARTS BUnpacking Iron Crate 1. Cut off the vinyl ropes that secure the top of the ROPS A : B1220 / B : B1620, B1820 / C : B1820ACE to the iron crate. UNIT 2. Take the diagonal member out of the front of the iron DESCRIPTION crate.
ASSEMBLY INSTRUCTIONS BContents of Accessory Case A : B1220 / B : B1620, B1820 / C : B1820ACE UNIT UNIT DESCRIPTION DESCRIPTION OPERATOR'S MANUAL LICENSE PLATE HOLDER WARRANTY STATEMENT LIGHT ASSY. (LICENSE) ASSEMBLY INSTRUCTIONS STAY (TRAILER SOCKET) SLOW BLOW FUSE LIGHT ASSY.
Page 7
ASSEMBLY INSTRUCTIONS A : B1220 / B : B1620, B1820 / C : B1820ACE UNIT UNIT DESCRIPTION DESCRIPTION FRONT TIRE ACCESSORIES B1620/B1820 ACCESSORIES 2 NUT (M12) BOLT (M8 x 20) HUB ACCESSORIES SPRING WASHER (M5) BOLT (M16 x 95) PAN HEAD SCREW (M5 x 30)
A Thoroughly read the Operator's manual before charging. A Insufficient charging will cause the battery to run down quickly, resulting in premature battery failure. A : B1220 / B : B1620, B1820 / C : B1820ACE UNIT DESCRIPTION RING JOINT PIN...
ASSEMBLY INSTRUCTIONS BMounting the Right and Left Fenders BInstalling the Lever Grip 1. Move the left-side two levers of the tractor to the low Install the lever grips onto the control levers. See the position. figure. 2. Tilt the front of the left-hand fender (1), insert the two levers (2) in the lever guide (3).
Secure the tail cover (4) tightening the M8 x 20 bolt (5) and M8 nut (6). BAttaching the Tail Cover and Rear Fender Stay [B1220] 1. Secure the tail light cover stay (LH and RH) (1) to their respective tail light covers (2) with two tapping screws (3).
ASSEMBLY INSTRUCTIONS 4. Install the tail light assembly (1) with the M8 x 20 bolt (2) to the right rear of the tractor. BAttaching the Tail Light and License Holder Stay [B1620, B1820] 1. Attach the tail light (1) to the tail light cover (2). 2.
ASSEMBLY INSTRUCTIONS 5. Connect the tail light cable to the wire harness cable with the 1-P coupler (8). BAttaching the Tail Light, Rear Fender Stay 6. Connect the rear turn signal / hazard light cables to the and the Turn Signal/Hazard Light wire harness cables with the 1-P coupler (3).
ASSEMBLY INSTRUCTIONS 4. Connect the combination light cables to the wire harness cable with the 1-P coupler (1). BAttaching the Front Combination Light [B1620, B1820] 1. Attach the front winker stay (1) with the M6 x 14 bolts A When connecting the cables, pass the cable (2) (2) and M6 flange nuts (3).
ASSEMBLY INSTRUCTIONS BAttaching the License Light and Trailer Electrical Outlet [B1620, B1820] 1. Attach the license light (2) to the license light stay (1) with the washers and nuts (3). 2. Attach the license light stay (1) to the license plate holder (4) with the two M5 x 16 pan head screws (5) and two flange nuts (6).
2. Attach the seat (1) and set the snap pin (3). 3. Apply the OPC seat cover (4) to the seat (1) with the bolts (5). [B1220] BAttaching the Check Plate 1. Attach the check plate (1) with the M6 x 16 bolt (2).
ASSEMBLY INSTRUCTIONS A Rear end : Hook to ROPS as indicated in the figure. BHoisting the Tractor To avoid personal injury: A Set blocks and/or safety stands under the tractor when suspended, to prevent falling, before working under neath. C Hoist and jigs 1.
ASSEMBLY INSTRUCTIONS 8. Check air pressure in the rear tires. BAttaching the Rear Tires 1. Attach the left and right hub (1) to the rear tires with six A Refer to the Operator's Manual for the proper air M14 nuts (2), spring washers (3) and plain washers (4) pressure.
ASSEMBLY INSTRUCTIONS BHooking up the Battery BAttaching the Tool Box 1. Perform the following after the battery has received a [B1820ACE] good charge (specific gravity: 1.26/20 C). 1. Remove the M8 x 20 bolt (1). (1) Check that the battery fluid is at an intermediate 2.