Sony trinitron PVM-1450QM Service Manual page 17

Operating through menus
There are five buttons for menu operations on the front of
the monitor. To display the main menu, first press MENU.
The buttons you can use appear at the bottom of the menu
screen.
Functions of the buttons
Button To select menu To adjust menu item
item
selected
MENU return to the return to the previous
.:i:li•
previous menu menu
ENTER
decide a selected
select an item
lja!~:51
item
move the cursor
increase selected value
--
(.,..) upwards
move the cursor decrease selected value
(.,..) downwards
ligilll
reset current adjustment
value to the factory
setting
(The above items in white type correspond to the marks in
the menu.)
front of monitor
Bl Ci LINE/ EXT
COMPONENT SDI AGB SYNC
D D G
[CJ
..
w
D
Q
D
BL E UNDER HIV 16:9
0 LY SCAN DELAY
RESET
button
[Il
Main menu
buttons for
menu
operations
Select an item and press ENTER to go to the folio.wing
menu.
~
CHROMA SET UP menu
Set to ON to adjust the internal decoder for CHROMA
and PHASE (NTSC signal only) after AUTO ADJUST
(ffi]). (OFF)
@)
COLOR TEMP/BAL menu
Select the color temperature from among 6500K, 9300K
and USER. USER is set to 6500K in the factory setting.
You can adjust or change the color temperature in USER
mode (a measuring instrument is needed). (6500K)
@]
USER CONFIG 1 menu
Select an item to adjust. To go to the USER CONFIG 2
menu, select NEXT I' AGE.
ffi)
USER CONFIG 2 menu
Select an item to adjust. To go to the USER CONr-IG 1
menu select PREVIOUS PAGE.
[ID
AUTO ADJUST screen
Select the color bar signal (full, SMPTE, EIA) and press
ENTER to start auto adjusting for CHROMA SET UP
(NTSC signal only).
(l]
ADJUST GAIN screen
Adjust GAIN in USER mode.
(ID
ADJUST BIAS screen
Adjust BIAS in USER mode.
(ID
COLOR TEMP RANGE menu
Select the color temperature range in USER mode.
[S0OOK-lOO00K)
[ill
COLOR SYSTEM DISPLAY menu
Select the color system display mode. In AUTO, the kind
of color system being used appears on the screen each
time you change the signal input. (AUTO)
[TI]
358 TRAP Fil TER menu
Color spill or color noise may be eliminated if you select
ON (NTSC signal only). !OFF!
[gj
SUB CONTROL screen
You can finely adjust the controls on the front panel.
CONTRAST, BRIGHT, CHROMA and PHASE control
has a click at the center of its adjustment range. You can
adjust the setting of the click position with this feature.
~
USER PRESET menu
You can preset each control to a desired level and set it.
If you set USER PRESET to ON, the REMOTE indicator
lights up and the controls on the front panel do not
work. The monitor operates with the internal memory
settings. For adjustment, select PRESET ADJUST. [OFF!
~
PRESET ADJUST screen
Adjust CONTRAST, BRIGHT, CHROMA, PHASE,
VOLUME, APERTURE in USER PRESET.
[ill
V HOLD screen
Adjust the vertical hold if the picture rolls vertically.
When you cannot read the display, select the input that
is not connected.
[j]]
COMPONENT LEVEL menu
Select the component level from among three modes.
N10/SMPTE for 100/0/100/0 sign.ii
BETA 7.5 for 100/7.5/75/7.5 signal
BET AO for 100/0/75/0 signal
[N10/SMPTEI
[TI]
NTSC SETUP LEVEL menu
Select the NTSC setup level from two modes. The 7.5
setup level is mainly used in north America. The 0 setup
level is mainly used in Japan. [OJ
5]I
ACC menu
Set ACC (Auto Color Control) circuit on or off. When the
fine adjustment is needed, set ACC to OFF. Normally set
it to ON. [ONI
~
LANGUAGE menu
You can select the menu language from among the five
languages (English, German, French, Italian, Spanish) on
the menu.
[ENGLISH!
(I
I indicates the foctory setting position.)
7
- 17 -