LG 42PM4M Owner's Manual page 34

Set ID
Set ID
- Use this function to specify a monitor ID number.
- Refer to 'Real Data Mapping 1'. See page 35.
PICTURE
Language
Child lock
SOUND
ISM Method
TIMER
Set ID
SPECIAL
Tile mode
SCREEN
Low power
Demo
Fan
Menu Prev.
1. Press the MENU button and then use the
2. Press the G G button and then use
3. Press the button and then use
G G
• The adjustment range of Set ID is 1 ~ 99.
Communication Parameters
Communication Parameters
• Baud rate : 9600 bps (UART)
• Data length : 8 bits
• Parity : None
Command Reference List Command Reference List
COMMAND 1 COMMAND 2
01. Power
02. Input Select
03. Aspect Ratio
04. Screen Mute
05. Volume Mute
06. Volume Control
07. Contrast
08. Brightness
09. Color
10. Tint
11. Sharpness
12. OSD Select
13. Remote Control Lock Mode k
14. Balance
15. Color Temperature
16. Abnomal state
17. ISM mode
18. Auto configuration
19. Key
20. Tile Mode
21. Tile H Size
22. Tile V Size
23. Tile ID Set
24. Elapsed time return
25. Temperature value
26. Lamp fault check
button to select the
D D / E E
button to select Set ID.
D D / E E
button to adjust Set ID to choose the desired monitor ID number.
F / G
• Stop bit : 1 bit
• Communication code : ASCII code
DATA
(Hexadecimal)
k a 0 ~ 1
k b 1 ~ 9
k c 0 ~ 3
k d 0 ~ 1
k e 0 ~ 1
k f 0 ~ 64
k g 0 ~ 64
k h 0 ~ 64
k i 0 ~ 64
k j 0 ~ 64
k k 0 ~ 64
k l 0 ~ 1
m 0 ~ 1
k n 0 ~ 3
k q 0 ~ 3
k r 0 ~ 64
k s 0 ~ 64
k t 0 ~ 64
k u 0 ~ 3
k v 0 ~ 14
k w 0 ~ 14
k $ 0 ~ 14
k y 1 ~ 9
k z 0 ~ a
j p 0 ~ 3
j q 0 ~ 1
PICTURE
Language
Child lock
SOUND
ISM Method
TIMER
Set ID
SPECIAL
Tile mode
SCREEN
Low power
Demo
Fan
Menu Prev.
SPECIAL menu.
T T ransmission / Receiving Protocol ransmission / Receiving Protocol
Transmission
[Command1][Command2][ ][Set ID][ ][Data][Cr]
* [Command 1]: k, j, m,d
* [Command 2]: To control Plasma Monitor set.
* [Set ID]: You can adjust the set ID to choose desired moni-
tor ID number in Special menu. Adjustment range
is 1 ~ 99. When selecting Set ID '0', every con-
nected Plasma Monitor set is controlled. Set ID is
indicated as decimal (1~99) on menu and as
Hexa decimal (0x0~0x63) on transmission/receiv-
ing protocol.
* [DATA]: To transmit command data.
Transmit 'FF' data to read status of command.
* [Cr]: Carriage Return
ASCII code '0x0D'
* [ ]: ASCII code 'space (0x20)'
OK Acknowledgement
[Command2][ ][Set ID][ ][OK][Data][x]
* The Monitor transmits ACK (acknowledgement) based on
this format when receiving normal data. At this time, if the
data is data read mode, it indicates present status data. If
the data is data write mode, it returns the data of the PC
computer.
Error Acknowledgement
[Command2][ ][Set ID][ ][NG][x]
* * If there is error, it returns NG
External Control Device Setup
G G
1
Owner's Manual 33