Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for DSE DSE103 MKII
Summary of Contents for DSE DSE103 MKII
- Page 1 DEEP SEA ELECTRONICS PLC DSE103 MK II Speed Switch Operators Manual Document number 057-135 Author : Paul Gibbons DSE103 MKII Operator Manual Issue 1 CALL US TODAY REQUEST A QUOTE SHOP ONLINE 1-888-POWER-58 parts@genpowerusa.com www.genpowerusa.com...
- Page 2 Applications for the copyright holder’s written permission to reproduce any part of this publication should be addressed to Deep Sea Electronics Plc at the address above. The DSE logo is a UK registered trademark of Deep Sea Electronics PLC. Any reference to trademarked product names used within this publication is owned by their respective companies.
- Page 3 DSE103 MKII Operating Manual TABLE OF CONTENTS Section Page BIBLIOGRAPHY ....................4 INSTALLATION INSTRUCTIONS ..................4 MANUALS ..........................4 CONFIGURATION SOFTWARE ..................4 INTRODUCTION ....................5 SPECIFICATIONS .................... 6 PART NUMBERING ......................6 TERMINAL SPECIFICATION ....................6 POWER SUPPLY REQUIREMENTS .................. 6 INPUTS ..........................
-
Page 4: Bibliography
DSE103 MKII Operating Manual 1 BIBLIOGRAPHY This document refers to and is referred to by the following DSE publications which can be obtained from the DSE website www.deepseaplc.com 1.1 INSTALLATION INSTRUCTIONS Installation instructions are supplied with the product in the box and are intended as a ‘quick start’ guide only. -
Page 5: Introduction
DSE website at www.deepseaplc.com The DSE103 MKII Series Speed Switch is designed to monitor the speed of an engine or piece of rotating machinery by detecting a magnetic pickup pulse or frequency. Should these exceed the configured trip points, the appropriate relay contact will change state. -
Page 6: Specifications
3 SPECIFICATIONS 3.1 PART NUMBERING 0103 Variant Product type Standard DSE 103 MKII Speed product switch. MKII Hardware revision Initial module release At the time of this document production, there are no variants of this product. 3.2 TERMINAL SPECIFICATION Connection type Two part connector. -
Page 7: Inputs
Magnetic Pickup devices can often be ‘shared’ between two or more devices. For example, one device can often supply the signal to both the DSE103 MKII speed switch and the engine governor. The possibility of this depends upon the amount of current that the magnetic pickup can supply. -
Page 8: Outputs
Max distance 6m (yards) 3.6.1.1 USB P813 INTERFACE CONNECTION The USB P813 is available to connect a PC to DSE103 MKII Speed Switch. Using the DSE Configuration Suite Lite software, the operator is then able to configure the DSE103 MKII Speed Switch. - Page 9 Green lead - Pin 2 Supply – Blue lead - Pin 5 Reset Yellow lead - Pin 13 Set NOTE:- Refer to DSE103MKII Configuration Suite Lite Manual (DSE part 057-136) for further details on configuring and control CALL US TODAY REQUEST A QUOTE...
-
Page 10: Dimensions And Mounting
DSE103 MKII Operating Manual 3.7 DIMENSIONS AND MOUNTING 3.7.1.1 DIMENSIONS 87.5 mm x 72.0 mm x 26.0 mm (3.4” x 2.8” x 1.0”) 3.7.1.2 MOUNTING Bolt & Nut Size: M4 Torque Rating: 0.60 Nm to 0.70 Nm CALL US TODAY... -
Page 11: Installation
DSE103 MKII Operating Manual 4 INSTALLATION The DSE103 MKII module is designed to be mounted with two x M4 bolt and nut. For dimension and mounting details, see the section entitled Specification, Dimension and mounting elsewhere in this document. 4.1 TERMINAL NUMBER AND DESCRIPTION... -
Page 12: Typical Wiring Diagram
DSE103 MKII Operating Manual 4.2 TYPICAL WIRING DIAGRAM Magnetic Pickup or Frequency input CALL US TODAY REQUEST A QUOTE SHOP ONLINE 1-888-POWER-58 parts@genpowerusa.com www.genpowerusa.com... -
Page 13: Settings And Adjustment
Turn the pre-set potentiometers to set the trip point. The factory setting for Trip 1 is 10% to 50% of nominal engine speed and the default setting for Trip 2 is 90% to 140% of nominal engine speed . The range is adjusted from 0% to 400% of nominal engine speed via the DSE Configuration Suite Lite PC Software. •... -
Page 14: Applicable Standards
10.3. Make all checks on the engine and alternator as detailed by their respective manufacturer documentation. 10.4. Check all other parts in the system according to the manufacturer documentation. 10.5. Thoroughly review the configuration of the DSE 103 MKII Speed switch and check that all parameters meet the requirements of your system. -
Page 15: Fault Finding
9 MAINTENANCE, SPARES, REPAIR AND SERVICING The DSE103 MKII Speed switch Series controller is Fit and Forget. As such, there are no user serviceable parts within the controller. In the case of malfunction, you should contact your original equipment manufacturer (OEM). - Page 16 DSE103 MKII Operating Manual This page intentionally is blank CALL US TODAY REQUEST A QUOTE SHOP ONLINE 1-888-POWER-58 parts@genpowerusa.com www.genpowerusa.com...
Need help?
Do you have a question about the DSE103 MKII and is the answer not in the manual?
Questions and answers