Table of Contents
Advertisement
Quick Links
Installation instructions for part AX-TYAMP1-SWC
Lexus/Toyota Amp Interface with SWC
• Provides accessory power (12-volt 10-amp)
• Retains audio controls on the steering wheel
• Provides NAV outputs (parking brake and
reverse)
LEXUS
TOYOTA
ES Series
2007-2012
4-Runner
ES Series (w/
Avalon
multi disc) 2002-2006
(Camry) Solara
IS Series
2002-2005
RX Series
2004-2008
Camry
(w/o nav)
Camry
Corolla
FJ Cruiser
®
AX-TYAMP1-SWC
2002-2015
INTERFACE FEATURES
• Retains the factory AUX-IN jack
• Designed for amplified models
• Retains balance
• Micro "B" USB updatable
APPLICATIONS
TOYOTA (CONT)
2003-2013
Highlander
2008-2013
2011-2012
Matrix
2005-2012
Prius 3rd Gen
2004-2008
(w/o nav)
2012-2015
Plug-In (PHV)
2012-2013
(w/o nav)
2012-2015
2007-2011
Prius
2004-2011
2003-2011
Rav-4
2004-2014.5
2011-2014
Sequoia (w/o nav) 2013
Connections To Be Made ................................................2-3
3.5mm jack steering wheel control retention ............. 3
Installing The Ax-Tyamp1-Swc ....................................... 3
Initializing The Ax-Tyamp1-Swc ..................................... 4
Adjusting The Ax-Tyamp1-Swc ....................................... 4
Steering Wheel Control Extra Settings...........................5-7
L.e.d. Feedback ............................................................. 5
Changing Radio Type ..................................................... 5
Remapping The Steering Wheel Control Buttons .......... 6
Resetting The Ax-Tyamp1-Swc ................................... 7
INTERFACE COMPONENTS
• AX-TYAMP1-SWC interface • AX-TYAMP1-SWC harness
• Female 3.5mm connector with stripped lead
TOYOTA (CONT)
Sequoia
2005-2012
TOOLS REQUIRED
Sienna
2004-2014
• Wire cutter • Crimp tool • Solder gun • Tape
Tacoma
2005-2013
• Connectors (example: butt-connectors, bell caps, etc.)
Tundra
2006-2013
• Small flat-blade screwdriver
Tundra
(Double Cab) 2004-2005
CAUTION!
Venza (w/ SD card
especially air bag indicator lights must be connected before cycling
based nav) 2013-2014
the ignition. Also, do not remove the factory radio with the key in the
Venza
2009-2012
on position, or while the vehicle is running.
Table of Contents
All accessories, switches, climate controls panels, and
Advertisement
Table of Contents
Related Manuals for Axxess AX-TYAMP1-SWC
Summary of Contents for Axxess AX-TYAMP1-SWC
- Page 1 • Provides NAV outputs (parking brake and • Retains balance reverse) Resetting the AX-TYAMP1-SWC ........7 • Micro “B” USB updatable INTERFACE COMPONENTS APPLICATIONS • AX-TYAMP1-SWC interface • AX-TYAMP1-SWC harness • Female 3.5mm connector with stripped lead LEXUS TOYOTA TOYOTA (CONT) TOYOTA (CONT) ES Series...
- Page 2 • Connect the Blue wire to the power antenna wire. • Connect the Gray wire to the right front positive speaker output. Attention! The AX-TYAMP1-SWC will work with both early and late generation • Connect the Gray/Black wire to the right front negative speaker output.
-
Page 3: Mm Jack Steering Wheel Control Retention
For the radios listed below, connect the included female 3.5mm connector with stripped leads onto the male 3.5mm SWC jack of the AX-TYAMP1-SWC. Any remaining wires, tape off and disregard : • Connect the AX-TYAMP1-SWC harness to the wiring harness in the vehicle. -
Page 4: Initializing The Ax-Tyamp1-Swc
® AX-TYAMP1-SWC Adjusting the AX-TYAMP1-SWC Initializing the AX-TYAMP1-SWC Audio level adjustment For the steps below, the Red L.E.D. (located inside the interface, next to the potentiometer) can only be seen while active. The interface does not need to be • With the vehicle and radio turned on, turn the volume up 3/4 of the way. -
Page 5: Steering Wheel Control Extra Settings
4. Press and hold the Volume-Up button until the L.E.D. goes solid, and then * Note: If the AX-TYAMP1-SWC flashes Red (7) times, and you do not have an Alpine radio release. Repeat this step for the desired radio number you have selected. -
Page 6: Remapping The Steering Wheel Control Buttons
Mute. Follow the steps below to remap the steering wheel control buttons 4. Seek-Down/Prev 13. On-Hook * 1. Ensure the AX-TYAMP1-SWC is visible so you can see the L.E.D. flashes to 5. Source/Mode 14. Off-Hook * confirm button recognition. - Page 7 Dual assignment legend 1. Not allowed 5. Mode/Source 10. Band 15. Fan-Up * The AX-TYAMP1-SWC has the capability to assign (2) functions to a single button, except Volume-Up and Volume-Down. Follow the steps below to 2. Not allowed 6. ATT/Mute 11. Play/Enter 16.
- Page 8 Please have the vehicle apart and ready to perform troubleshooting steps before calling. If only the finest quality will do, then look no further than Axxess products. Accept no compromises, choose only quality OE integration interfaces.
Need help?
Do you have a question about the AX-TYAMP1-SWC and is the answer not in the manual?
Questions and answers