Page 1
Rev. 3-2-2012 CZ-53X Series IR Night Vision Fast Dome Cameras Available Models: CZ-537-10X 520TVL 10X PTZ Camera CZ-533-4 650TVL Fixed 4mm PT Camera CZ-533-8 650TVL Fixed 8mm PT Camera CZ-533-12 650TVL Fixed 12mm PT Camera CZ-531-4 520TVL Fixed 4mm PT Camera...
1 Instruction These series of products can be widely used in intelligent building, bank security, urban roads, airport terminals and bus stations, and also are able to satisfy various demands from any square and activities occasion. 1.1 Safety Instructions Make sure to read the user manual before using the product.
2.2 Specifications Model IR Mini Variable Speed Dome Camera Help Selection Ceiling Power Supply DC12V/2A 50Hz/60Hz ≤15W Power Pan Speed 0.5°~40°/ sec Tilt Speed 0.5°~20°/ sec Pan Range 360°continuous Tilt Range 0°~90° auto flip Preset Pan Scan frame scan; 360° random scan; 360° continuous scan; Pattern Cruise OSD Menu...
3 Functions 3.1 Setting Address Code Setting address code before using the dome camera, it could be setup by the dip-switch or soft address. 3.2 Zoom/ Rotation Auto Match Technology The camera can adjust automatically pan tilt speed according to the zoom far or near, make sure easier to operate manual motion detection.
3.7 Auto Cruise The preset #99 is programmed to be recalled in sequence. This feature is called auto cruise. Call preset #99 to start preset #1 to #20 cruises, call preset #88, start preset #1~#10, call preset #89, start preset #11~#20 cruise. 3.8 Pattern A pattern is a saved, repeating, series of pan, tilt, zoom and preset functions that can be recalled with a command from a controller or automatically by a...
Power supply: DC12V/2A RS485: Output RS485 signal, connect the camera. BNC Connector: Output Video Signal. 4. 3 Dip Switch Setup Dip Switch as follows: Notice: Dip Switch Address Setup see appendix I 5 Operation Note: The manual will refer to our CCTV tester to explain how to operate and control the camera.
5.1 Power On Self -Check When power on, the camera moves automatically from pan range to tilt range, after movement, pull the lens to the nearest and then to the farthest, make sure the camera is running in normal. PROTOCOL: AUTO BAUD RATE: AUTO...
5.3.3 Iris Press “Iris Open” key to adjust the brightness. 5.4 Setting the preset Following the steps to set preset: (1) Select Camera. (2) Control joystick, Proportion Key and Iris Key to adjust the picture. (3) Press preset No. + PRESET, save the parameter of the picture. 5.4 Calling the preset Following the steps to review preset: Press designated preset + CALL...
Page 12
MAIN MENU SYSTEM INFORMATION ADDR SETTING MOTION PATTERNS CAMERA CRUISE SETTING IR SETTING DISPLAY SETUP RESTORE FACTORY DEFAULT REBOOT SYSTEM EXIT <SYSTEM INFORMATION>: Shows system information. <ADDR SETTING>: Select and setup Soft/Hard address. <MOTION>: Setup for motion related settings. ...
6.2.1 System Information SYSTEM INFORMATION 2400, N, 8, 1 ADDRESS SOFTWARE VERSION V5.2 BACK EXIT <COM>: Shows current Baud rate. <ADDRESS>: Shows current Camera ID for PTZ control, 0~255. <SOFTWARE VERSION>: Shows current software version of camera. Notice: The system information can not be changed.
6.2.3 Motion MOTION FRAME SCAN POWER UP NONE PARK TIME PARK ACTION NONE BACK EXIT Frame Scan FRAME SCAN SET SCAN POSITION CLEAR FRAME SCAN FRAME SCAN SPEED BACK EXIT <SET SCAN POSITION>: Set up scan range between two positions (Left/Right extreme position).
enter below interface: SET FRAME SCAN RIGHT LIMIT POSITION IRIS OPEN TO CONTINUE 6.2.3.2 Clear Frame Scan CLEAR FRAME SCAN IRIS OPEN TO CONTINUE Move the cursor to “Clear Frame Scan” to enter, then press “Iris Open” to delete the extreme positions. 6.2.4 Patterns PATTERNS PATTERN NUMBER...
6.2.5 Camera Setup We are using Samsung SDM-100P camera to explain below operation. MAIN MENU CAMERA LABEL WHITE BALANCE AUTO AUTO DETECTION FOCUS EXPOSURE ADDITIONAL MENU BACK EXIT Notice: “Up/Down” keys for option, “Left/Right” keys for details, “Iris Open” for sub-menu. ...
Page 17
<WHITE BALANCE>: WB Mode: Auto Trace / Manual / Auto (1) Auto Trace : Indoor/Outdoor, The camera can automatically adjust ambient light from1800K~10500K(Indoor: 3000~10,500K; Outdoor: 1,800~10,500K), to ensure the most nature image effect. AUTO TRACE WB AUTO TRACE WB MODE OUTDOOR EXIT (2) Manual: Close auto WB, adjust Red and Blue level manually.
Page 18
MOTION DETECTION ALARM SELECT REGION REGION MODE 20…|..………. BOTTOM 25….…|……. LEFT 20…|.………. RIGHT 40….……|…. EXIT Alarm: On/Off Region:1~4 Region Mode: On / Off <FOCUS> FOCUS MODE AUTO ZOOM TRACE MODE ZOOM TRACE SPEED FAST DIGITAL ZOOM SHOW ZOOM INITIAL ZOOM POSITION LENS INITIALIZATION EXIT ♦...
Page 19
The target is very smooth( like car surface) The brightness contrast of the target is not very clear. Too strong high light or back light. Too high contrast. Some shade in front of the target. ①...
Page 20
cursor to “On”, then press “Iris Open” to set up. INITIAL ZOOM POSITION INITIAL ZOOM POSITION EXIT Zoom Range: X1~X10 ♦ <LENS INITIALIZATION>: press “Iris open/Set” key to initialize the lens. ♦ <EXPOSURE>: EXPOSURE BRIGHTNESS 25….…|……. IRIS AUTO SHUTTER —— SSNR SENS-UP EXIT...
Page 21
24X、32X、64X、128X、1/120000、1/60000、1/30000、1/10000、/1/7000、 1/5000、1/2500、1/1600、1/1000、1/700、1/500、1/250、1/100、1/50. MANUAL SHUTTER SHUTTER 1/50 EXIT Notice: Auto shutter setting only for manual iris mode. <AGC>: High / Middle / Off / Manual Enhances image brightness automatically in case that luminance level of image signal is too low. Range: 5-41 LEVEL EXIT...
Page 22
♦ <ADDITIONAL MENU>: ADDITIONAL MENU USER PRESET SETUP PRIVACY ZONE MASK DAY & NIGHT AUTO 1 SYNC. SYSTEM INTERNAL IMAGE ADJUSTMENT RE-BOOT EXIT ① USER PRESET SETUP: On / Off USER PRESET USER PRESET NUMBER NO 1 USER PRESET MODE SAVE CLEAR EXIT...
Page 23
<Focus>: Using direction keys to “Focus” and press “Iris/Open” key to set up. FOCUS MODE AUTO ZOOM TRACE MODE ZOOM TRACE SPEED FAST DIGITAL ZOOM SHOW ZOOM EXIT <OTHER>: refer to below details. OTHER CAMERA TYPE AUTO TRACE BW MOTION DETECTION PRIVACY MASK DAY &...
Page 24
② PRIVACY MASK: PRIVACY MASK GROUP SELECTION AREA SELECTION ZONE MODE COLOR 50…|..………. 50…|..………. BOTTOM 104….…|……. LEFT 50…|.………. RIGHT 98……|…… EXIT <GROUP SELECTION>: 1~ 8 <AREA SELECTION>: 1~ 4 zones / group <ZONE MODE>: On / Off ...
Page 25
⑤ IMAGE ADJUSTMENT: IMAGE ADJUSTMENT FREEZE HORIZONTAL FLIP VERTICAL FLIP SHARPNESS 50….…|……. EXIT <FREEZE>: Camera starts freezing the image of start point, as soon as camera stops at preset end point, camera starts display live images. <HORIZONTAL FLIP>: image will flip 180°when you start up. Normal when shutdown.
lower than setting IR value. 81~254 could be optional. <CURRENT LEVEL>: the current IR light value. Use direction key of CCTV Tester to modify preset and confirm by press “Iris/Open” key. 6.2.8 Display Setup DISPLAY SETUP PRESET LABEL P/T DEG BRIGHT DATA BACK EXIT...
7 Trouble Shooting Troubles Reason Solution 1. The power supply DC12V is not 1. Correct the connection. No action connected correctly. 2. Check the power supply is when power on 2. The fuse is broken. connected, or confirms if the plug connects well. 3.
Appendix I DIP Switch Setup K1 DIP switch is an address switch, consist of 8 number, use 8421 binary code, max 255 address. When the switch is in the “ON” position, the number from 1~8 corresponding to 1, 2, 4, 8, 16, 32, 64, 128. For example, if you set 1, 3, 5, 7 switch to the “ON”...
Page 35
1 0 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Notice: some protocols and address start from 0, if you can not control the dome camera, try to do ±1 of address code.