Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Niko NK-97CHE
Summary of Contents for Niko NK-97CHE
- Page 2 NIKO Speed Dome Camera. This product is designed to be installed and utilized indoors for the purpose of crime prevention in the large buildings, such as department stores, hotels and offices not to mention small buildings. This instruction manual contains the contents that users must be well informed of this product.
-
Page 3: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS IN THIS OWNER S MANUAL. AND THOSE MARKED ON THE PRODUCT. RETAIN THIS BOOKLET FOR FUTURE REFERENCE. This product has been designed and manufactured to assure personal safety. Improper use can result in electric shock or fire hazard. -
Page 4: Table Of Contents
Table of Contents Introduction Auto Pan ....26 Important Safety Instructions ..3 Table of Contents ... . .4 About Dome Camera . -
Page 5: About Dome Camera
Depending on how peripheral connection devices are hooked up, there are 4 models of it produced and put on the market. NK-97CHE : PC or DVR Connection type NK-97CHS : Sensor Connection type NK-98CHE : PC or DVR Connection type, Day & Night NK-98CHS : Sensor Connection type, Day &... - Page 6 Introduction Zoom Lens & Auto Focus Zooming is possible from 22/27 times (the optical zoom limit), to a maximum of X10 times digital magnification. Sensor Linkage (NK-97CHS/NK-98CHS) The camera is capable of capturing a subject by the focus of camera moving promptly toward the subject at the rate of 360 /sec when the camera works with a detector (magnetic, beam, infrared rays), and a subject moving within a detec- tion area is captured by a detector.
-
Page 7: Safety Precautions
Introduction Safety Precautions Do not attempt to disas- Handle the camera semble the camera with care To prevent electric shock, do not remove Do not abuse the camera. Avoid strik- screws or covers. There are no user ing, shaking, etc. The camera could be serviceable parts inside. - Page 8 Introduction Do not use the camera Before operating, please in such places as shown check proper tempera- below. ture, humidity and power source ratings. The lens may become cloudy due to condensation if the camera is used Use the camera under conditions under the following conditions.
-
Page 9: What's In The Box
Introduction What's in the box Decoration Cover Screws Camera Body Connector Camera Mounting Base OPTIONAL Outdoor Wall Housing Outdoor Pendant Housing Indoor Dome Housing... -
Page 10: Identification Of Camera
Introduction Identification of Camera Aluminum Ring Lens Dome Cover Horizontal Movement start point & Camera Fixture Hole Power Source & Data Connection Terminal Alarm signal input Terminal (NK-97/ 98/CHS only) Video Output Terminal Connection Hole... -
Page 11: Camera Installation
Getting Started Camera Installation Precautions The following steps of installation and connection should be taken by qualified service personnel or system engineer and should conform to all installation regulations. Make sure to switch the camera off before installation and connection. Switches Setting The DIP switch of the camera is a 6-bit switch and employs RS-485 communica- tion mode as basic use. -
Page 12: Getting Started
Getting Started DIP Switch Function No. ON Function Effect Communication Noise decreases Terminate when 2 cameras or more are installed. Baud Rate 19,200 BPS (communication speed) Baud Rate 9600 BPS (communication speed) Baud Rate 4800 BPS (communication speed) Baud Rate 2400 BPS (communication speed) Camera Basic Setup Mode... -
Page 13: Getting Started
Getting Started The table for the camera ID setting camera Switch camera Switch camera Switch camera Switch No.1 No.2 No.1 No.2 No.1 No.2 No.1 No.2... -
Page 14: Getting Started
Getting Started camera Switch camera Switch camera Switch camera Switch No.1 No.2 No.1 No.2 No.1 No.2 No.1 No.2 Precautions The default setting of the camera ID is 1. Camera ID 0 can control all of speed dome camera independent of camera ID number. -
Page 15: Connecting Wires
Getting Started Assembly & Installation procedures Camera mounting base Make 5.5cm hole in diameter in the ceiling board to run the cable. Note Be sure to select a ceiling board strong enough to sup- port 4 times as heavy as the total weight of the camera.
Need help?
Do you have a question about the NK-97CHE and is the answer not in the manual?
Questions and answers