For body worn operation, Loner Duo has been assessed for RF exposure and meets the requirments of FCC KDB447498 and IC RSS-102. / Pour utilisation sur le crops, Loner Duo a été évalué pour l’exposition aux RF et répond aux exigences de la FCC KDB447498 et IC RSS-102.
It is important for you to be aware of the following precautions. DANGER Do not place a Blackline GPS Product in or near an open flame or in the pres- ence of flammable gases or fumes. Operation of any electrical equipment in potentially explosive atmospheres can constitute a safety hazard.
Page 7
Operate Blackline GPS products outside their specified humidity rating. Consult the specifications section. Dispose of Blackline GPS products in your household trash. Seek advice from your local electronics recycling authority. Blackline products may contain an internal lithium-ion battery pack.
Getting Started Service Activation Your Loner Duo requires a valid Loner Mobile application license operating on a support- ed smart phone. Contact your company’s safety coordinator or Blackline GPS customer care at customercare@blacklinegps.com to obtain a license. Please see Using the Loner Duo for detailed instructions.
The Loner Duo promotes a safe work environment for you when: Bluetooth communication has been established with the smartphone running Loner Mobile. The Loner Duo and the smart phone both have sufficient battery capacity to operate. You are wearing the device and carrying the associated smartphone.
Using the Loner Duo Loner Duo Hardware Details The Loner Duo is rugged and purpose-built for monitoring you as a mobile worker. Physical details are outlined below. Physical Feature Charging Port Charges the Loner Duo. Power Button & Powers the Loner Duo and indicates the Indicator Light Bluetooth connection status.
Page 11
Indicator Light Array Power Button & Indicator Light Emergency Latch (pull) Acknowledge Button (push) Belt Clip Product Label Charging Light (on bottom) Charging Port...
The first time the Loner Duo powers on, you must pair it with a smartphone running the Loner Mobile application. 1. Press the Power Button to turn the Loner Duo on. The Loner Duo will turn on, the green Indicator Light will blink and the beeper, Indicator Light Array and vibration motor will annunciate the chirp pattern.
7. The smart phone and the Loner Duo will establish communications. 8. Once paired, the Loner Duo green Indicator Light will remain on continuously. If the Loner Duo fails to connect via Bluetooth to the smart phone, the device will enter the no Bluetooth alarm pattern.
The Loner Duo is referred to as having no Bluetooth connection when the Power Button Indicator Light is blinking or the device is powered off. The Loner Duo is referred to as having a Bluetooth connection when the Power Button Indicator Light is on continuously.
4. Wait for the device to establish a Bluetooth connection. The Power Button Indicator Light remains on continuously. 5. Wear the Loner Duo on your belt at your hip at all times that you require remote safety monitoring. 6. Perform your work duties as you normally would. The Loner Duo automates remote monitoring of your safety.
Alerts Alert messages are configured for Loner Mobile and Loner Duo through the Loner Portal web application. Alerts are displayed in Loner Portal and can be sent via email and SMS to safety monitoring personnel. Alerts An alert is a message that communicates a device or system level event such as an Emergency Alert or a Low Battery Alert.
2. Press and hold the Acknowledge Button for 3 seconds. 3. Cancel the alert in Loner Mobile. After three seconds, the alarm pattern will be silenced and the Loner Duo will return to regular operation. If the user cancels an Emergency Alert, this does not clear the alert within the Loner Portal user account.
Portal user account. Monitoring personnel are required to address the safety incident. About Fall Detection The Loner Duo is constantly monitoring your motion for falls. If the Loner Duo detects a fall, it will enter the alarm mode and annunciate the low alarm pattern to indicate a pending Fall Detected alert.
Canceling a pending Missed Check-in Alert: 1. Press the Acknowledge Button for 1 second. 2. After one second, the alarm pattern will be silenced and the Loner Duo will return to regular operation. If you have not cancelled the alert within 30 secondes, the Missed Check-in Alert is sent, initiating the alert escalation process.
The Loner Duo utilizes gyroscope and accelerometers to determine the motion of normal human activity and thus determine when an extreme event, such as a fall, occurs. Accuracy of the system depends on the user wearing the Loner Duo correctly on the belt at the hip. // USER GUIDE...
Specifications Specifications for Loner Duo Software Compatibility Power & Battery Rechargeable Li-ion battery: 350 mAh capacity Loner Mobile version 3.x for BlackBerry Battery life: 12 hours continuous operation Size & Weight Charging connector: 4-pin sealed connection Size: 51 mm W x 32 mm H x 62 mm L (2.01” W x 1.26” H x 2.44” L) Environmental Weight: 75 g (2.65 oz)
More details can be found in the specifications section. Customer Care Customer Care for the Loner Duo Customer Care for the Loner Duo is available between the hours of 8 and 5 Mountain Time. North America toll-free: 1-877-869-7212 | International: 1-403-451-0327 Email: support@blacklinegps.com...
Need help?
Do you have a question about the Loner DUO and is the answer not in the manual?
Questions and answers