Download Print this page

Advertisement

Available languages

Available languages

Quick Links

RANGE HOOD INSTALLATION INSTRUCTIONS
For questions about features, operation/performance, parts, accessories, or service, call: 1-800-253-1301.
Residential range hoods can be installed to comply with Sections 308 and 309 of ADA Guidelines when used with appropriately
mounted controls installed at 15" (38.1 cm) to 40" (101.6 cm) above the floor, and control access should not require reaching over
a cooking appliance.
The following range hoods can work in an ADA-compliant situation when the range hood is wired to operate from a dedicated
standard electrical wall switch. To facilitate this application, share the information on the following pages with your electrician
when preparing for the installation.
NOTE: All the models can be controlled only by one remote switch. The switch activates or deactivates the motor and the light
of the hood.
Two-Speed Range Hoods
(with rocker switch)
UXT20
UXT30
UXT40
UXT41

Tools and Parts

Tools Needed
Wire stripper
Parts Needed
UL Listed/CSA
UL Listed/CSA
Approved wire
connectors
UL Listed single pole
toggle light switch
W11108368A
FOR ADA COMPLIANCE
In Canada, for assistance, installation, and service, call: 1-800-607-6777.
UXT42

INSTALLATION REQUIREMENTS

#2 Phillips
Flat-blade
screwdriver
screwdriver
UL Listed #14
Approved
(minimum)
1/2" (13 mm)
3 wire cable
strain relief
UL Listed deep
single-gang
switch box
Intermediate Range Hoods
(with rotary switch)
Observe all governing codes and ordinances.
Ensure that the electrical installation is adequate and in
conformance with National Electrical Code, ANSI/NFPA 70
(latest edition), or CSA Standards C22.1-94, Canadian Electrical
Code, Part 1 and C22.2 No. 0-M91 (latest edition) and all local
codes and ordinances.
If codes permit and a separate ground wire is used, it is
recommended that a qualified electrician determine that the
ground path is adequate.
A copy of the above code standards can be obtained from:
A 120-volt, 60 Hz., AC-only, 15-amp fused electrical circuit
is required.
Three-Speed Range Hoods
(with push buttons)
UXT52
WVU37U

Electrical Requirements

National Fire Protection Association
1 Batterymarch Park
Quincy, MA 02169-7471
CSA International
8501 East Pleasant Valley Road
Cleveland, OH 44131-5575

Advertisement

loading

Summary of Contents for Whirlpool UXT20

  • Page 1: Installation Requirements

    NOTE: All the models can be controlled only by one remote switch. The switch activates or deactivates the motor and the light of the hood. Two-Speed Range Hoods Intermediate Range Hoods Three-Speed Range Hoods (with rocker switch) (with rotary switch) (with push buttons) UXT20 UXT42 UXT52 ■ ■ ■ UXT30 ■...
  • Page 2: Installation Instructions

    INSTALLATION INSTRUCTIONS 2. Attach the power cable to the switch box. WARNING Clamp wiring to switch box and unit using a UL Listed or CSA Approved 1/2" (13 mm) strain relief. Provide 6" (15.2 cm) leads inside box and fan for easier wiring. 3.
  • Page 3 Hottes de cuisine à deux vitesses Hottes de cuisine intermédiaires Hottes de cuisine à trois vitesses (avec interrupteur à bascule) (avec interrupteur rotatif) (avec boutons poussoirs) UXT20 UXT42 UXT52 ■ ■ ■ UXT30 ■...
  • Page 4 INSTRUCTIONS D’INSTALLATION 2. Fixer le câble d'alimentation à la boîte d'interrupteur. AVERTISSEMENT Serrer le câblage à la boîte d'interrupteur et à l'unité au moyen d'un serre-câble de 1/2" (13 mm) homologué UL/ CSA. Prévoir des fils de 6" (15,2 cm) à l'intérieur de la boîte et du ventilateur pour faciliter le câblage.

This manual is also suitable for:

Uxt30Uxt40Uxt41Uxt42Uxt52Wvu37u