Page 1
JCP3-N01 Control Panel - NVG Installation and Operating Manual Rev. A Jupiter Avionics Corporation 1959 Kirschner Road Kelowna BC Canada V1Y 4N7 Tel: +1 778 478 2232 Toll-Free: 1 855 478 2232 www.jupiteravionics.com...
Page 2
All rights reserved Jupiter Avionics Corporation (JAC) permits a single copy of this manual to be printed or downloaded for the express use of an installing agency. Any such electronic or printed copy of this manual must contain the complete text of this copyright notice.
JCP3-N01 Control Panel - NVG SECTION 1 - DESCRIPTION System Overview The JCP3-N01 Control Panel - NVG is part of an aircraft audio system consisting of the control panel and a remote audio controller. Figure 1-1 Aircraft Audio System The control panel has the switches and level controls that allow the user to operate the remote audio controller.
JCP3-N01 Control Panel - NVG Installation and Operating Manual Inputs and Outputs Refer to the JCP3-N01 connector maps for the mating connector designators and pin assignments for the input and output signals. 1.3.1 Inputs Name Type CALL ANNUNCIATOR Active low discrete...
Installation kit part number INST-JCPX 1.4.3 Environmental Specifications The JCP3-N01 Control Panel has been qualified to the environmental conditions listed below. Environmental categories for which TSO compliance has been demonstrated are listed in the Environmental Qualification Form Appendix B of this manual.
Introduction This section contains unpacking and inspection procedures, installation information, and post-installation checks. Continued Airworthiness Maintenance of the JCP3-N01 is on condition only. Scheduled inspection and/or periodic maintenance of this unit is not required. Unpacking and Inspecting Equipment Unpack the equipment carefully. Check for shipping damage and report any problems to the relevant carrier. Confirm that the Authorized Release Certificate or Certificate of Conformance is included.
2.4.3 Mechanical Installation The JCP3-N01 can be mounted in any attitude and location with adequate space for the front panel and sufficient clearance for the connector and wiring harness. It requires no direct cooling. 2.4.4 Legend Replacement The JCP3-N01 illuminated legends are field replaceable.
The configuration program ProCS™ can be used to customize the text for each legend either at the time of ordering the unit, or if text changes are required after installation. The JCP3-N01 need not be connected to a computer to select the legend text.
ProCS Setup - JA99, ProCS Setup - CAB-USB-0006 and ProCS Setup - Virtual Panel show the connections used for testing the JCP3-N01. These setup drawings would not be used in normal operation. ProCS Setup - JRAC-001 shows the cabling for using the JCP3-N01 for configuring the JRAC-xxx using ProCS™ (see section 2.6.1 above).
This section contains the operating instructions for the JCP3-N01. The JCP3-N01 acts as a control panel for a remote Audio controller such as the Jupiter Avionics JRAC-001. The JCP3-N01 commands the remote audio controller, and this manual is written to describe the results of any operation of the JCP3-N01 controls.
JCP3-N01 Control Panel - NVG Installation and Operating Manual Transceiver Switches These are six white two-position toggle switches. When a switch is set to the ‘up’ position, audio from the associated transceiver is routed to the phones. The legends (above the switches) are interchangeable to allow customization.
JCP3-N01 Control Panel - NVG Installation and Operating Manual Music/Configuration Connector Cover (♫/io) This is a music input that is compatible with most music players. It accepts a 3 pole 3.5mm stereo plug with a slim diameter connector housing. (This connector is also used during installation to change configuration settings for the JRAC-001.)
JCP3-N01 Control Panel - NVG Installation and Operating Manual VOX Threshold Control This is a rotary knob that is used to select the VOX threshold of the unit. See below. When rotated fully clockwise (cw), the threshold will be at maximum and VOX ICS operation is disabled and ICS PTT input is required for ICS operation.
JCP3-N01 Control Panel - NVG Installation and Operating Manual Normal Operation Mode Note: Numbers in parentheses refer to the front panel controls shown in section 3.2. The Audio System is in Normal mode when the front panel EMER / NORM switch (4) is in the NORM position and suitable electrical power is supplied to the audio system (Control Panel and Remote Audio Controller).
JCP3-N01 Control Panel - NVG Installation and Operating Manual 3.3.6 Multi-Function (XMIT / ICS) Switch Operation Note: At installation, this switch may be configured to operate in default or alternative mode. Check with your installing agency for confirmation of the operation of this switch.
Appendix A - Installation Drawings Introduction The drawings necessary for installation and troubleshooting of the JCP3-N01 Control Panel - NVG are in this Appendix, as listed below. Note: A fully customized set of Connector Maps and Interconnects can be created using the ProCS™...
Page 19
CHECKED TITLE Control Panel - NVG P1 Main Connector 09-14-17 APPROVED NCAGE CODE PART NO. SHEET L00N3 JCP3-N01 DOC NO. CONFIDENTIAL & PROPRIETARY TO JUPITER AVIONICS CORP. JCP3-N01 Connector Map Rev A.dwg JUPITER AVIONICS TEMPLATE AUTOCAD PORTRAIT SIZEA REV B.DWT...
Page 23
MUSIC RIGHT MUSIC LEFT PREPARED TAT/CPM 09-14-17 CHECKED TITLE Control Panel - NVG Configuration and Music Options 09-14-17 APPROVED NCAGE CODE PART NO. SHEET L00N3 JCP3-N01 DOC NO. JCP3-N01 Interconnect Rev A.dwg JUPITER AVIONICS TEMPLATE AUTOCAD PORTRAIT SIZEA REV B.DWT...
Page 25
Jupiter Avionics Corporation Audio Controllers Legend Replacement Field-Replaceable Legends Extractor tool Jupiter Avionics Corporation (JAC) products have field-replaceable illuminated recess legends. This permits easy customization, and allows the same units to be used in multiple different configurations with only minimal changes.
Installing Agency in preparing Instructions for Continued Airworthiness (ICA) when replacing an existing audio panel with a Jupiter Avionics JCP3-N01 Control Panel - NVG. This sample may be modified appropriately for new installations. It is the installer’s responsibility to determine the applicability of the method used. Installations performed outside Canada must follow the applicable aviation authority’s regulations...
Page 28
Refer to the JCP3-N01 Maintenance Manual. 7. Removal and Replacement Information Refer to Section 2 of this manual - the JCP3-N01 Installation and Operating Manual. If the unit is removed and reinstalled, a functional check of the equipment should be conducted.
Page 29
JCP3-N01 CAN-TSO Design Change Assessment Rev A Manufacturer’s Specification JCP3-001 Declaration of Design and Performance Rev B and/or Other Applicable Specification: JCP3-N01 Derivative Declaration of Design and Performance Rev A Manufacturer: Jupiter Avionics Corporation Address: 1959 Kirschner Road, Kelowna, BC, Canada, V1Y 4N7 Revision &...
Page 30
JCP3-N01 Control Panel - NVG Environmental Qualification Form CONDITIONS SECTION DESCRIPTION OF TESTS CONDUCTED Explosive Atmosphere Equipment identified as Category X, no test performed Waterproofness 10.0 Equipment identified as Category X, no test performed Fluids Susceptibility 11.0 Equipment identified as Category X, no test performed Sand and Dust 12.0...
Page 31
REMARKS This product is a derivative of the JCP3-001. All tests were performed on the JCP3-001. A similarity analysis between the two products is detailed in the Jupiter Avionics Corp. document JCP3-N01 CAN-TSO Design Change Assessment Rev A. Test information can be found in the Jupiter Avionics Corp. document: JCP3-001 Test Report (Qualification - Final) Rev A During exposure to vibration test conditions all critical resonances changed frequency less than 1.5%.