Related Manuals for Hyon HR1900P
Summary of Contents for Hyon HR1900P
- Page 1 RF Repeater Installation and Operational Manual (Model: HR1900P) Teletech Home Repeater JAS Teletech...
-
Page 2: Table Of Contents
Table of Contents 1. General Information 1.1 Introduction 1.2 Specifications 1.3 Description 2. Installation 2.1 Introduction 2.2 Unpacking and Inspection 2.3 Preparation for Use 2.4 Before Installation 2.5 Antenna Installation 2.6 Repeater Installation 2.7 Connectors 2.8 Installation Example 3. Operation 3.1 Introduction 3.2 Operating Instructions 4. -
Page 3: General Information
1. General Information 1.1 Introduction This manual provides information pertaining to the installation and operation of JAS Teletech’s HR1900P Home Repeater. This Unit is for CDMS, GSM, and TDMA modulations in the PCS frequencies as shown in Table 1-1. <Tebla 1-1: HR1900P>... -
Page 4: Specifications
1.2 Specifications <Table 1-2: HR1900P Specifications> Specifications Parameters Remarks Downlink Uplink 1930~1990MHz 1850~1910MHz 60MHz B.W Frequency Range Output Power +7dBm /1FA[Max.] Gain 50dB ±2dB/Fc Gain Flatness ≤ 7dB ≥ -45dBc/30KHz Fc +885KHz ≥ -45dBc/30KHz Fc -885KHz In Band Spurious ≥ -50dBc/30KHz Fc +1.98MHz... -
Page 5: Description
HR1900P is approximately 2.5 Watts. 2.3.2 Operating Environment The HR1900P is intended for indoor use only. Do not install it where it might be exposed to the outside elements as this could result in destruction of the unit and other hazards. -
Page 6: Before Installation
Maximum Humidity: 95% 2.4 Before Installation You will need to determine the following before beginning the HR1900P installation: a. Base Station location b. Location where the outdoor antenna is to be installed c. Location where the indoor antenna is to be installed d. -
Page 7: Connectors
2.6.2 Antenna Isolation and Alignment HR1900P is equipped with an over drive protection circuit. If the output power level of uplink exceeds prescribed limit, then uplink is disconnected and the FAIL LED(RED) is on. Repeater automatically checks output power level every 1 minute of a 5 minute cycle when uplink has over power. -
Page 8: Installation Example
SMA-type female connector transmit mobile RF, receives base station RF, and connects to the indoor antenna <Figure 2-7: HR1900P Connectors> To Mobile To Base 2.8 Installation Example HR1900P can be installed as shown in Figure 2-8. Home Repeater JAS Teletech... -
Page 9: Operation
(please refer to the section 2.6.2 of this manual for antenna alignment and isolation.) The overdrive fail on the HR1900P repeater is design to detect whether the over driving is transient or permanent. If the output power level of uplink exceeds prescribed limit ,then uplink is disconnected and the FAIL LED(RED) is on. - Page 10 CAUTION! There are no user serviceable parts in the HR1900P. DO NOT OPEN the unit. There is a danger of an electric shock. Opening the covers of the unit will void all warranties. Home Repeater JAS Teletech...
-
Page 11: Drawings
5. Drawings 5.1 Front and Back views <Figure 5-1: HR1900P Front view> 5.2 Top and Bottom views Home Repeater JAS Teletech... - Page 12 Bottom 5.3 Side views Home Repeater JAS Teletech...
Need help?
Do you have a question about the HR1900P and is the answer not in the manual?
Questions and answers