Commands - Overview - H&B DAD 141.1 Technical Manual

Commands – Overview
9.
Command Short description
AA Get/set analog output action (base)
AD
Communication: Device Address
AG Absolute gain calibration
AH Get/set analog high
AI'n' Assign Input 'n' to 1 out of 15 different functions/base
AL Get/set analog low
AM
Analog Output Mode Current / Voltage
A'n' Action for Setpoint 'n': choose 0 of 8 different base for setpoint 'n'
AS Save analog output parameters
AZ Absolute zero point calibration
BR Communication: Baud Rate
CE Calibration: Open Calibration Sequence; Read TAC Counter
CG Calibration: Set Calibration Gain (Span) at Load > Zero
CI Calibration: Minimum Output Value
CL Communication: Close Device
CM
Calibration: Set Maximum Output Value
CS Save the Calibration Data (CM, CI, DS, DP, etc.) to the EEPROM
Calibration: Set Calibration Zero Point – Scale Without Load
CZ
DP Calibration: Set Decimal Point Position
DS Calibration: Set Display Step Size
DX Communication: Set full-duplex (1) or half duplex (0)
FD Factory default settings: Write Data to the EEPROM (TAC protected)
FM Read / modify filter mode: IIR (0) or FIR (1)
FL Digital low pass filter: Filter Cut-off Frequency
GA
Output: Get Triggered Average Value
GG Output: Get Gross Value
GH Get Hold Value
Retrieves an image file from the DAD141.1's EEPROM
GI
GN
Output: Get Net Value
GM
Get Peak (Maximum) Value
GO Get Peak tp Peak Value
GS Output: Get ADC Sample Value
GT Output: Get Tare Value
GV Get Valley Value
Output: Get Data String "Net/Gros/Status"
GW
H'n'
Hysteresis for Setpoint H0 (S0) or H1 (S1) or H2 (S2)
HT Trigger function: Hold time for Violation of Setpoint Limit
ID Device information: Identify Device
IH
Hardware version
IN Logic input: for each Input Status 0 or 1
IO Logic output: for each Output Status 0 or 1
IS Device information: Identify Device Status
IV Device information: Identify Firmware Version
MT Trigger function: Measuring Time for Averaging
NA Network Address <aaa.bbb.ccc.ddd>
NR Motion detection: No-motion Range
NT Motion detection: No-motion Time Period
DAD 141.1 Technical Manual, Rev. 2.5 – April 2015
Parameter value Page
0 through 8 48
0...255 47
± 32000 34
-999999 to 999999 48
0 to 15 43
-999999 to 999999 48
0 to 5 48
0 to 8 45
none 49
± 32000 34
9600...115200 baud
47
0...65535 31
1...999999 32
–999999...0
31
None 47
1...999999 31
None 34, 49
None 32
0...5 32
1, 2, 5, 10, ..., 500
32
0 or 1 47
None 33
0 or 1 36
0...8 36
None 41, 50
None 40
None 41
None 49
None 40
None 41
None 41
None 40
None 40
None 41
None 40
-9999...+9999 45
0...65535 ms 46
None 30
None 30
0000...0011
43
0000...0111
44
None 30
None 30
0...3000 ms 50
e.g. 192.168.0.100 47
0...65535 d 35
0...65535 ms 35
Page 28 of 54