Table of Contents
Advertisement
Quick Links
Quic
Quic k Star
Quic
Quic
Quic
ER450 Da
ER450 Da
ER450 Da
ER450 Da
ER450 Da ta R
1.0 Introduction
Welcome to the Quick Start Guide for the ER450 Data
Radio. This guide provides step-by-step instructions, with
simple explanations to get you up-and-running. For
further information, please refer to the E Series User
Manual.
Contents
1.0 Introduction............................................................ 1
3.0 Connecting Antennas and RF Feeders.................. 3
4.0 Communications Ports........................................... 4
5.0 Power Supply and Protection..................................5
6.0 TVIEW+ Management Suite...................................7
7.0 Optimising the Antenna for VSWR......................... 6
8.0 LED Indicators and Test Outputs........................... 6
9.0 Verifying Operational Health.................................. 7
10.0 Support Options..................................................... 8
Quick Start Guide - ER450 Data Radio
k Star t Guide
k Star
k Star
k Star
ta R
ta R
ta R
ta R adio
Related Products and Documentation
•
•
•
•
•
•
t Guide
t Guide
t Guide
t Guide
adio
adio
adio
adio
Base Station EB450
Hot Standby Base Station EH450
Digital Order Wire Voice Module EDOVM
Duplexers
TVIEW+ Management Suite
E Series User Manual
1
Advertisement
Table of Contents
Related Manuals for Trio ER450
Summary of Contents for Trio ER450
-
Page 1: Table Of Contents
R adio adio adio 1.0 Introduction Welcome to the Quick Start Guide for the ER450 Data Radio. This guide provides step-by-step instructions, with simple explanations to get you up-and-running. For further information, please refer to the E Series User Manual. -
Page 2: Mounting And Environmental Considerations
2.0 Mounting and Environmental 2.2 ER450 Connections Layout Considerations The ER450 radio comes complete with a mounting cradle and is attached to a panel or tray by means of screws or bolts, using the hole slots provided. Note: In high power or high temperature applications, it is desirable to mount the radio with the heatsink uppermost to allow ventalation for the heatsink. -
Page 3: Connecting Antennas And Rf Feeders
Not used accordance with the manufacturers notes. Pin 4 Shutdown Pin 5 Not used The RF connector used on the ER450 radio is an N Type Pin 6 Not used female connector. Always use good quality low loss Pin 7 Ground... - Page 4 Caution: When the radio is configured to transmit the radio modem can be configured to transmit • continuously, ensure an RF load is present BEFORE applying power to the unit. continuously whenever powered, or Quick Start Guide - ER450 Data Radio...
-
Page 5: Power Supply And Protection
6.0 TVIEW+ Management Suite - (fusing) Radio Configuration The ER450 radio modem is designed and calibrated to This TVIEW+ Management Suite allows a number of operate from a 13.8Vdc regulated supply, but will operate features including: Configuration (Local - serial, or from 10-16 volts (filtered) DC. -
Page 6: Optimising The Antenna For Vswr
An RTS loop as described in Section 4.4, or b) A system port PTT plug as described in Section 4.1 Refer to the User Manual for further details of VSWR testing. LED Legend Quick Start Guide - ER450 Data Radio... -
Page 7: Verifying Operational Health
Half Duplex - Master or Slave (Rx) received data to be output to the port is shown as a GREEN flash. If data is alternately flowing in and out quickly, then the indicator appears orange. LED Legend Quick Start Guide - ER450 Data Radio... -
Page 8: Support Options
F +613 9775 0606 E support@trio.com.au www.trio.com.au www.trio.com.au www.trio.com.au www.trio.com.au www.trio.com.au Innovative and sophisticated digital communications Issue 2: December 2002 Information subject to change without notice. designs products and solutions © Copyright 2002 Trio DataCom Pty Ltd. All rights reserved.