Advertisement
Booster Fitting Kit
for the Pondless
Fountain RainXchange
Installation Instructions
• Step-by-Step Installation Instructions
for the Booster Fitting Kit
(Item #30214)
Aquascape water feature pumps are designed to
provide high flows at low pressures to waterfalls and
streams. They are not designed to provide sufficient pressure
for garden hose or irrigation applications. As a result, a separate
Booster Pump is required with the RainXchange
for irrigation or other watering chores such as car, deck or patio washing.
The Booster Pump is an external pump with a built-in pressure tank and electronic controller.
The Booster Pump is available in two sizes: a ¼ HP model (item # 30084) and a larger ½ HP (item
# 30085) model for applications requiring higher pressure for professional irrigation systems.
The Booster Pump has a built-in thermal overload and run-dry shut off to protect the pump when
water becomes too low in the RainXchange
Pump Shutoff Switch (item #29647) to prevent the Booster Pump from using all the water in the
RainXchange
water storage basin. This will leave a small supply of water in the basin for the
™
water feature pump to continue to operate. (See Figure 1 on page 6 of manual.)
High Pressure Sprinkler and Drip Irrigation: The RainXchange
professionally installed irrigation. We recommend consulting a professional irrigation installer
in order to properly configure the RainXchange
Note: Water from the RainXchange
water. Pre-filters designed for sprinklers and drip systems are recommended.
The Booster Pump is able to operate on either 110V or 230V single phase. See the manual
included with the Booster Pump for electrical and performance specifications, as well as
pump maintenance information.
Waterfall or Decorative
®
System
™
Systems when being used
™
water storage basin. We recommend a Low Water
™
System into the design of these applications.
™
System may contain more suspended sediment than tap
™
Aquascape, Inc.
St. Charles, IL 60174 • Brampton, ON L6T 5V7
www.aquascapeinc.com
c a p t u r e > f i lt e r > r e u s e
System can be used with
™
Advertisement
Table of Contents
Related Manuals for AquaScape 30214
Summary of Contents for AquaScape 30214
- Page 1 • Step-by-Step Installation Instructions for the Booster Fitting Kit (Item #30214) Aquascape water feature pumps are designed to provide high flows at low pressures to waterfalls and streams. They are not designed to provide sufficient pressure for garden hose or irrigation applications. As a result, a separate...
- Page 2 Booster Pump, you must prime the pump first. To do ™ this, simply make sure that your Aquascape water feature pump is running. Next, rotate the red knob on top of the Booster Pump counterclockwise until water begins to trickle Ball Valve out.
- Page 3 Booster Pump, you must prime the pump first. To do Snorkel and Centipede this, simply make sure that your Aquascape water feature pump is running. Next, rotate the red knob on top of the Booster Pump counterclockwise until water begins to trickle out.
- Page 4 a q u a s c a p e r a i n x c h a n g e ™ c a p t u r e > f i lt e r > r e u s e Installation for the Low Water Pump Shut off Switch (item #29647) The Low Water Shut off Switch (item #29647) is shown mounted...
- Page 5 Booster Pump is abused, misused, or used for a GARANTIE GARANTIE purpose other than for which the product is intended. DE 1 AN DE 1 AN Item #30214.102008 ©2008 Aquascape, Inc. • All Worldwide Rights Reserved IDD 08106790-AI 080244...
Need help?
Do you have a question about the 30214 and is the answer not in the manual?
Questions and answers