Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for JBL CBT1000
Summary of Contents for JBL CBT1000
- Page 1 CBT1000 and CBT1000E Bracket Installation Guide Rev C CBT1000E CBT1000...
- Page 2 Hardware Included with CBT1000: SPEAKER WALL SWIVEL Tools Required: BRACKETS BRACKETS LINK BRACKETS 4 Bracket Parts for UPPER M6 Hex Wrench ← Mounting Position on Cabinet (when set for 0° or for down-tilting) #2 Phillips Head Screwdriver 3 Bracket Parts for LOWER ←...
- Page 3 ARM LINK (which is utilized for the larger tilt angles). 1) RUN WIRING -- Run the wiring from the power amplifier to the location desired for mounting the JBL CBT Loudspeakers. Note: Connect wire to speaker terminals at a point in the installation process when convenient for your installation circumstances.
- Page 4 3) ATTACH SPEAKER SIDE OF BRACKET TO SPEAKER Mount the SPEAKER BRACKET (2 pcs) to the speaker with the provided M8 x20 mm pan-head bolts, in the locations shown and in the orientation shown in the diagram below. Option 3a) CBT 1000 with No Swivel (for Down-Tilt Capability [or 0° tilt] and No Horizontal Swivel/Pan). 8 PLACES: M8 x 20 mm FLAT WASHER...
- Page 5 Option 3b) CBT 1000 with Up-Tilt Capability -- No Horizontal Swivel/Pan 8 PLACES: M8 x 20 mm FLAT WASHER PAN HEAD BOLT M8 SPLIT LOCK WASHER Up-tilt range 0° to +15°...
- Page 6 Option 3c) CBT1000 Mounting with Down-Tilt Capability and SWIVEL BRACKET (for Horizontal Swivel/Pan aiming capability) 8 PLACES: M6 Hex Wrench M6 x 20 mm SOCKET HEAD BOLT M6 SPLIT LOCK WASHERS M6 FLAT WASHERS 8 PLACES: FLAT WASHER M8 SPLIT...
- Page 7 Option 3d) CBT1000 Mounting with Up-Tilt Capability and SWIVEL BRACKET (for Horizontal Swivel/Pan aiming capability) 8 PLACES: M6 Hex Wrench M6 x 20 mm SOCKET HEAD BOLT M6 SPLIT LOCK WASHERS M6 FLAT WASHERS 8 PLACES: FLAT WASHER M8 SPLIT...
- Page 8 For Options 3c and 3d (configurations that include the SWIVEL BRACKET), place RUBBER WASHERS as shown when using SWIVEL BRACKET: RUBBER WASHERS to be placed between SWIVEL BRACKET and SPEAKER BRACKET 4) Jump to page 15 for CBT 1000 tilt angling instructions.
- Page 9 (which get added to the SPEAKER BRACKETS if utilized for horizontal swivel/pan aiming capability), and an ARM LINK (which is utilized for the larger tilt angles). 1) RUN WIRING -- Run the wiring from the power amplifier to the location desired for mounting the JBL CBT Loudspeakers.
- Page 10 3) ATTACHING COUPLER PLATE -- Connect the CBT 1000 and CBT 1000E together by attaching COUPLER PLATE to bottom four (4) insert points of the CBT 1000 and to top four (4) insert points of CBT 1000E using 8 pcs M8 x 20 PAN-HEAD PHILLIPS BOLTS with LOCK WASHERS and FLAT WASHERS.
- Page 11 4) ATTACH SPEAKER SIDE OF BRACKET TO SPEAKER Option 4a) CBT 1000+1000E System with No Swivel (for Down-Tilt Capability [or 0° tilt] and No Horizontal Swivel/Pan) 8 PLACES: M8 x 20 mm FLAT WASHER PAN HEAD BOLT M8 SPLIT LOCK WASHER Down-tilt range 0°...
- Page 12 Option 4b) CBT1000+1000E System with Up-Tilt Capability (No Horizontal Swivel/Pan) 8 PLACES: M8 x 20 mm FLAT WASHER PAN HEAD BOLT M8 SPLIT LOCK WASHER Up-tilt range 0° to +5.25°...
- Page 13 Option 4c) CBT1000+1000E System with Down-Tilt Capability and Horizontal Swivel/Pan 8 PLACES: M8 SPLIT LOCK WASHER M8 x 20 mm PAN HEAD FLAT WASHER BOLT SWIVEL BRACKET attaches to speaker via M8 x 20 mm PAN HEAD BOLTS (with lock washers and flatwashers).
- Page 14 Option 4d) CBT1000+1000E System with Up-Tilt Capability and Horizontal Swivel/Pan M8 x 20 mm FLAT WASHER PAN HEAD M8 SPLIT BOLT LOCK WASHER 8 PLACES: SWIVEL BRACKET attaches to speaker via M8 x 20 mm PAN HEAD BOLTS (with lock washers and flatwashers).
- Page 15 The following instructions apply to both the CBT1000 by itself and to the CBT 1000+1000E System. (For simplicity, drawings are shown with CBT1000 only.) 5) SLIDE SPEAKER WITH SPEAKER BRACKET ONTO WALL BRACKET Make sure the PIVOT BOLT is installed in-place in the SPEAKER BRACKET. The PIVOT BOLT ASSEMBLY consists of the M6 x 125 mm bolt with lock washer and flat washer on the head and secured in place with flat washer, lock washer and M6 cap nut.
- Page 16 6) SET THE TILT ANGLE 6a) For Setting Shallow Tilt Angles (0° to -3° for CBT1000; 0° to -0.9° for CBT1000+1000E System), do NOT use ARM LINK. Slide the M6 x 125 mm BOLT into labeled hole for desired down-tilt angle. Use LOCK WASHER and FLAT WASHER on head and FLATWASHER, LOCK WASHER, and CAP NUT on end of bolt.
- Page 17 6b) For Setting Larger Tilt Angles (-4° to -15° for CBT1000; -1.25° to -5.25° for CBT1000+E System), Use ARM LINK. Loosely attach the ARM LINK to the WALL BRACKET using the M6 x 115 mm bolt in hole A or B (depending on desired tilt angle -- refer to TILT ANGLE SETTINGS DIAGRAM).
- Page 18 Tilt Angle Settings Diagram Shown set in the 13° tilt setting for CBT1000, or 4.5° tilt setting for CBT 1000 + 1000E System (Marked A-13° in black and A-4.5° in orange, so other end of LINK ARM is at Point “A”)
- Page 19 See full size Tilt Angle Settings Diagram on previous page for detail of markings and settings ARM LINK Not Utilized = Bolt Setting Location(s) “System” = CBT 1000 + 1000E Point “C” CBT 1000: 0° CBT 1000: 1° CBT 1000: 2° CBT 1000: 3°...
- Page 20 7) SETTING HORIZONTAL SWIVEL (PAN) AIMING – With the 8 M6 x 20 mm SOCKET HEAD swivel screws loose (4 on top bracket and 4 on bottom bracket), set the horizontal swivel (pan) aiming angle. Tighten all 8 swivel screws. Once all components have been installed, use HEX WRENCH to loosen SWIVEL BRACKET and...
- Page 21 BRACKET PARTS DIMENSIONAL DIAGRAMS WALL BRACKET TOP/BOTTOM SECTIONS Narrow Pole-Strap [1.9] Slots [2.0] M6 Bolt Clearance Holes [7.7] Wide Pole-Strap Slots [2.0] [1.1] [7.3] [8.2] [4.1] [1.0] Center Recessed Channel for Improved Pole-Mount Stability Dims in mm [in]...
- Page 22 SPEAKER BRACKET TOP/BOTTOM SECTIONS [1.7] [4.4] M8 Bolt Clearance Holes [8.2] [6.8] M6 Bolt Clearance Holes [2.8] [1.8] 4 x M6 Threaded Inserts [4.4] [1.7] [9.0] M6 Bolt Clearance Hole [7.9] [2.9] [2.8] 4 x M6 Threaded Inserts Dims in mm [in]...
- Page 23 SWIVEL BRACKET TOP/BOTTOM SECTIONS [3.4] [2.8] [8.7] [7.1] [2.1] [4.4] [3.2] [4.8] [2.2] [3.4] [2.8] [9.4] [8.2] [3.2] [4.3] [3.2] [2.2] Dims in mm [in] [4.7]...
- Page 24 LINK ARM [3.6] [1.3] [3.8] [6.8] [4.1]...
- Page 25 APPENDIX A - MTC-CBT-OS2 Offset Bracket MTC-CBT-OS3 Offset Bracket must be used when the CBT 1000E (extender) is located on the top versus on the bottom of the CBT 1000 (full-range speaker). The optional MTC-CBT-OS3 bracket is part of the CBT1K-ACC1 kit. Hardware Included with MTC-CBT-OS3: MTC- CBT-OS3...
- Page 26 1) Attach MTC-CBT-OS3 to bottom 4 inserts of CBT 1000E using M8 PAN HEAD BOLTS with LOCKWASHERS AND FLATWASHERS 2) Attach top of COUPLER PLATE to MTC-CBT-OS3 BRACKET by inserting bolts through holes in MTC-CBT-OS3 BRACKET (3 on left side; 3 on right side) and thread into captured nuts in COUPLER PLATE (6 places)
- Page 27 Completed Assembly...
- Page 28 JBL Professional 8500 Balboa Blvd. Northridge, CA 91329 CBT1000 Brkt RevC U.S.A. 10/17...