Subscribe to Our Youtube Channel
Related Manuals for Lister A 1600-3
Summary of Contents for Lister A 1600-3
- Page 1 OPERATING INSTRUCTION ANIMAL CLIPPER with rechargeable Battery-Pack Equi Akku Perfekt Perfekt Perfekt Perfekt TYP A 1600-3 Equi - Clip Akku Perfekt Typ A 1600-3 Release: 10 / 2012 (09932103330)
-
Page 2: Table Of Contents
TABLE OF CONTENTS 1 Safety Instruction ................. Page 3 - 6 General information Symbols and warning indications Correct use Safety basics 1.4.1 Safety regulations 1.4.2 Precautions for the charger station 1.4.3 Precautions for the battery-pack 1.4.4 General safety measures 1.4.5 Radiation 1.4.6 Maintenance and inspection instructions 1.4.7 Sound-pressure level 1.4.8 Vibration... -
Page 3: General Information
SAFETY INSTRUCTIONS General information These safety instructions contain basic indications to be observed during set up, operation and maintenance. All persons operating or working with the clipping machine must read these operating instructions most carefully. The operating instructions should always be available at the place where the appliance is operated. -
Page 4: Safety Basics
Safety basics Please keep these important information! They contain most important information about safety and handling of the animal clipper and the charger station. The incorrect usage of the charger station and the animal clipper may be hazardous! Please observe the following measures for accident protection before putting the appliance into operation 1.4.1 Safety regulations Put the plug only into sockets that have been installed in accordance with the... -
Page 5: General Safety Measures
becomes too short for practical use. Do never dispose of an exhausted battery-pack by any other means. 1.4.4 General safety measures 1. Use the animal clipper with rechargeable battery-pack only for the purpose described in the instructions for use. 2. Never try to clip wet animals. 3. -
Page 6: Sound-Pressure Level
Operator responsibilities A safe use of the clipping machine only makes few demands upon the operator. Yet these are compulsory to be followed and observed: • The operator has read and understood this operating instruction, or has been instructed by an expert on the use and operation of the clipping machine and the dangers. -
Page 7: Equipment
Equipment 1 clipping machine with clipping head 1 set of clipper blades (mounted) 1 Battery-Pack (mounted) 1 Battery-Charger 1 spanner - with 4 mm 1 bottle of special-oil 1 operating instruction 1 case for transport and storing Options: Various different clipper blades PUTTING INTO OPERATION Charging the Battery-Pack Your new battery-pack is not charged when supplied. -
Page 8: Function Of Control Lamps On Battery-Charger
In case the battery-pack becomes heated (sunlight o. s.) the control light of the charger does not necessarily light up. If this happens first let the battery-pack cool down and then start charging. If the control light still does not light up there might be a foreign body in the battery compartment which has to be removed. -
Page 9: Correct Lubrication Of The Clipping Head
Correct lubrication of the clipping head Lack of lubrication is the most common cause of unsatisfactory clipping results and overheating of the clipping machine. For best clipping results as well as for enhancing life time of the clipping blades and the machine, apply a thin oil film on the blades. -
Page 10: Correct Adjustment Of The Clipper Blades
Correct adjustment of the clipper blades Adjust the clipper blades as follows: When machine is switched off: Please make sure that the taper pins of the carrier fit into the holes of the upper blade (picture 4). Unscrew the counter nut anti-clockwise and tighten the adjusting 4+10 screw clockwise until the first sensible resistance. -
Page 11: Pictures
Bildnachweis Page 11... -
Page 12: Repairs
REPAIRS Introduction The measures to remedy failures are mentioned in the column REMEDY/ACTION of the list of failures. Instructions marked with * are only to be carried out by authorised qualified personnel. List of problems In case of failures that are not listed below, please contact an authorised servicepoint (your authorised agent). - Page 13 Clipping head Failure Cause Remedy / Action Upper blades does MS-eccentric broken * … replaced by specialist shop not move HGW-eccentric is defective or missing replace HGW-eccentric gearwheel (53 teeth) defective * … replaced by specialist shop Upper blade does MS-eccentric to reject * …...
-
Page 14: Exploded View / Spare Parts
EXPLODED VIEW / SPARE PARTS Clipper Head VIII Equi-Clip Akku Perfekt Pos. Description Part-No. adjusting screw zinc plated 19-8001826 clipping head housing VIII 19-8001800 spring guide pin 19-8001824 pressure regulation spring 19-3012014 sliding pin sheet metal 19-8001820 sliding pin HGW (2 pieces) 19-3030106 HGW-eccentric 19-3030107... - Page 15 Motor Unit Typ A 1600 incl. Charger and Battery-Pack Description Part-No. Motor housing, saphirblue 19-0401211 Connection plate, complete with cables, plugs 19-0401202 and overload protection Battery connection housing (saphirblue) 19-0401213 with Clip and Wrist Cord Switch 7,2 V DC 19-0401206 Motor 7,2 V DC with Gear (11 teeth) 19-0401208 Screw M 2,6 x 6 (2 pieces)
-
Page 16: Others
Pay attention to the regulations in force in your country! Declaration of Conformity This piece of equipment complies with directive: 2004/108/EC 2006/95/EC Manufactured by: Lister – GmbH / Germany P.O. Box 2160 58471 Lüdenscheid / Germany Phone: +49 2351 1060-0 Fax: +49 2351 1060–50 Email: Export@lister.de...
Need help?
Do you have a question about the A 1600-3 and is the answer not in the manual?
Questions and answers